SN75176 vs MAX485ECPA+ Comparaison
Comparaison détaillée côte à côte de SN75176 par Texas Instruments et MAX485ECPA+ par Maxim Integrated. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
SN75176 - Differential Bus Transceiver RS-485/RS-422 | Texas Instruments
SN75176 ✓ ActifMaxim Integrated
MAX485ECPA+ - 1 Mbps RS-485/RS-422 Half-Duplex Transceiver | Maxim
MAX485ECPA+ ✓ ActifComparaison des spécifications
| Paramètre | SN75176 | MAX485ECPA+ |
|---|---|---|
| Marque | Texas Instruments | Maxim Integrated |
| Catégorie | Interface ICs | Interface ICs |
| Statut du cycle de vie | Actif | Actif |
| Fonction | Transceiver | — |
| Protocol | RS-422, RS-485 | — |
| Number of Drivers/Receivers | 1/1 | — |
| Duplex | Half | — |
| Receiver Hysteresis | 50 mV (typical) | — |
| Supply Voltage (Vcc) | 4.75 V to 5.25 V | — |
| Température de fonctionnement | 0 °C to +70 °C | Commercial grade (C suffix) - [DATA_NEEDED: full operating temperature range] |
| Driver Output Current | ±60 mA (max) | [DATA_NEEDED: output current (standard / high-impedance load)] |
| Common-Mode Input Range | -7 V to +12 V | — |
| Differential Input Threshold | ±200 mV | — |
| Quiescent Supply Current (enabled) | 30 mA (typical) | — |
| Shutdown Supply Current | 1 µA (typical) | — |
| Boîtier | 8-pin PDIP (P) | PDIP-8 (8-pin plastic DIP, through-hole) |
| Type de montage | Through-Hole | Through Hole |
| Standards Compliance | ANSI TIA/EIA-422-B, TIA/EIA-485-A, ITU V.11, ITU X.27 | — |
| Statut RoHS | Compliant | Compliant (Maxim lead-free suffix '+') |
| Transceiver Configuration | — | 1 driver / 1 receiver, half-duplex |
| Interface Standard | — | RS-485 / RS-422 differential |
| Tension d'alimentation | — | 5 V nominal (4.5 V to 5.5 V) |
| Maximum Data Rate | — | 1 Mbps (slew-rate-limited driver) |
| Driver Output Type | — | Differential, limited slew rate |
| ESD Protection | — | +/-15 kV on driver outputs and receiver inputs |
| Quiescent (Supply) Current | — | [DATA_NEEDED: quiescent current] |
| Receiver Common-Mode Range | — | [DATA_NEEDED: receiver common-mode voltage range] |
| Receiver Input Sensitivity | — | [DATA_NEEDED: receiver differential threshold] |
| Driver Output Differential Voltage | — | [DATA_NEEDED: differential output voltage] |
| Enable Pins | — | DE (driver enable) and /RE (receiver enable, active-low), separate pins |
| Short-Circuit Protection | — | Yes, driver outputs are short-circuit current limited |
| Arrêt thermique | — | Yes, protects against excessive power dissipation |
| Quiescent Current Shutdown Pin | — | Not present on this device |
| Qualification | — | Industrial temperature option available in family - [DATA_NEEDED: AEC-Q100 status] |