THVD1450DRBR vs ISO1450BDWR Comparaison
Comparaison détaillée côte à côte de THVD1450DRBR par Texas Instruments et ISO1450BDWR par Texas Instruments. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI
THVD1450DRBR ✓ ActifTexas Instruments
ISO1450BDWR - 50Mbps 5kVrms Isolated RS-485/RS-422 Transceiver | Texas Instruments
ISO1450BDWR ✓ ActifComparaison des spécifications
| Paramètre | THVD1450DRBR | ISO1450BDWR |
|---|---|---|
| Marque | Texas Instruments | Texas Instruments |
| Catégorie | Interface ICs | Interface ICs |
| Statut du cycle de vie | Actif | Actif |
| Statut du stock | In Stock | In Stock |
| Prix unitaire (USD) | $1,25 | $2,95 |
| Product Type | RS-485/RS-422 Transceiver (half-duplex) | — |
| Number of Drivers/Receivers | 1/1 | — |
| Supply Voltage (VCC) | 3 V to 5.5 V | — |
| Maximum Data Rate | 50 Mbps | — |
| ESD Protection (Bus Pins) | ±18 kV IEC 61000-4-2 contact/air | — |
| EFT Immunity | ±4 kV IEC 61000-4-4 | — |
| Common-Mode Range | -7 V to +12 V | Wide common-mode bus voltage range (per datasheet) |
| Receiver Hysteresis | 30 mV | [DATA_NEEDED: receiver hysteresis voltage] |
| Receiver Fail-Safe | Internal biasing (idle/short/open = logic high) | — |
| Unit Load | 1 UL (32 nodes on bus) | 1/8 (up to 256 nodes on bus) |
| Température de fonctionnement | -40°C to +125°C | -40C to +125C |
| Boîtier | 8-VSON EP (DRB) 3x3 mm | SOIC-16 wide-body (DW), 16 pins |
| Type de montage | Surface Mount, wettable flank | Surface Mount |
| Moisture Sensitivity Level | MSL 1 | — |
| Statut RoHS | Compliant | Compliant |
| Duplex Mode | Half | — |
| Fonction | — | Isolated half-duplex RS-485 / RS-422 transceiver |
| Data Rate (max) | — | 50 Mbps |
| Isolation Voltage (rms) | — | 5 kVrms (reinforced) |
| Number of Drivers / Receivers | — | 1/1 |
| Duplex | — | Half |
| Supply Voltage VCC1 (logic side) | — | 3 V to 5.5 V |
| Supply Voltage VCC2 (bus side) | — | Internally generated by isolated DC-DC |
| Bus Pin ESD (IEC 61000-4-2) | — | ±16 kV (air / contact, per datasheet) |
| Bus Pin ESD (HBM) | — | ±4 kV |
| IEC 61000-4-4 EFT Immunity | — | ±4 kV |
| Surge Immunity | — | [DATA_NEEDED: IEC 61000-4-5 surge rating] |
| Arrêt thermique | — | Yes |
| Current Limiting | — | Yes |
| Low-Power Standby | — | Yes |
| Niveau MSL | — | 3 (per JEDEC J-STD-020) |
| Compliance Standards | — | TIA/EIA-485-A, TIA/EIA-422, IEC 61000-4-2, IEC 61000-4-4 |