AD602JN - Dual Low-Noise VGA, 35 MHz | Analog Devices
Référence : AD602JN ✓ ActifAD602JN Présentation
A variable-gain amplifier, or VGA, is an analog amplifier whose gain can be adjusted by an external control voltage. In the broader hierarchy, a VGA belongs to the amplifier IC and signal-conditioning categories, where it sits between a low-noise input stage and a downstream converter, detector, or display circuit. Unlike a fixed-gain amplifier, a VGA supports calibrated gain adjustment, ranging control, and gain normalization in systems whose input amplitude changes over time.
The AD602JN uses a linear-in-decibel gain response, making its control relationship easier to calibrate than a linear-in-voltage control law. Its two gain ranges, each covering 30 dB, support precise signal adjustment while the 0.3 dB absolute-gain accuracy provides predictable system-level amplitude calibration. The 1.4 nV/√Hz input-noise specification supports low-noise amplification, and the -60 dBc total harmonic distortion at a 1 V output places the device in the low-distortion signal-chain class.
Bandwidth extends to 35 MHz at the -3 dB point, allowing the AD602JN to process substantially higher frequencies than audio-only amplifiers. This bandwidth is important in ultrasound systems because received echoes can contain frequency components above the baseband range. The dual-channel architecture supports coherent processing of two signal streams without requiring two separate amplifiers, while independent gain controls allow each channel to be adjusted separately.
Typical uses include ultrasound receiver channels, medical imaging front ends, broadband test equipment, communications receivers, and other systems requiring accurate variable gain with low added noise. In an ultrasound receiver, the AD602JN can amplify a weak transducer signal while a control voltage establishes the gain required for a consistent downstream signal level. The same architecture can normalize sensor outputs before digitization or detection.
A primary design consideration is maintaining clean, decoupled power rails and keeping the gain-control path free from high-frequency interference. The gain-control voltage and surrounding circuitry must also preserve the intended linear-in-decibel behavior across the selected range. Because the 35 MHz bandwidth and 1 V output test condition characterize performance differently at different frequencies and amplitudes, system designers should evaluate noise, distortion, stability, and control bandwidth together rather than relying on a single headline specification.
This product summary combines the AD602 architecture, commercial-temperature grade, dual-channel gain capability, low-noise performance, and packaging details with practical guidance for selecting, comparing, and implementing the AD602JN in precision analog signal chains.
Alternatives de remplacement direct pour AD602JN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
AD600JN
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →AD602JN Valeurs maximales et caractéristiques électriques
| Number of Channels | 2 channels |
| Amplifier Type | Dual, low-noise, wideband variable-gain amplifier |
| Gain Range per Channel | -10 dB to +30 dB |
| Number of Gain Ranges | 2 gain ranges |
| Gain Range per Segment | 30 dB |
| Gain Control Response | Linear in dB |
| Absolute Gain Accuracy | 0.3 dB |
| Input Noise Density | 1.4 nV/√Hz |
| Total Harmonic Distortion | -60 dBc at 1 V output |
| -3 dB Bandwidth | Up to 35 MHz |
| Tension d'alimentation | ±5.25 V |
| Température de fonctionnement | 0 °C to +70 °C |
| Temperature Grade | Commercial |
| Boîtier | 16-lead PDIP |
| Package Type | PDIP |
| Nombre de broches | 16 pins |
| Type de montage | Through-hole |
Guide de configuration des broches du AD602JN pdip
Configuration des broches du AD602JN (boîtier pdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AD602JN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD602JN convient pour 6 applications: Ultrasound Receiver Signal Chain, Medical Imaging Front End, Broadband Signal Conditioning, Communications Receiver Front End, Test and Measurement Instrumentation, Industrial Sensor Interface.
Ultrasound Receiver Signal Chain
The AD602JN fits the variable-gain stage of an ultrasound receiver because each channel delivers independent -10 dB to +30 dB gain with 0.3 dB absolute-gain accuracy. Its 1.4 nV/√Hz input noise helps preserve weak echo information, while bandwidth to 35 MHz supports a broader received-frequency spectrum than an audio-band amplifier. Two channels can process related receive signals independently, reducing circuit count where coherent or parallel channels are required. The gain-control network should implement the intended linear-in-decibel scaling and be isolated from switching-node and clock-related noise.
Recommandé
Medical Imaging Front End
The AD602JN can normalize analog signals before digitization in medical imaging equipment that requires consistent amplitude across changing sensor conditions. Its two independent channels support paired signal paths, while the -10 dB to +30 dB range permits attenuation as well as amplification. The 0.3 dB absolute-gain accuracy supports predictable calibration, and the -60 dBc distortion specification at 1 V output helps preserve low-level signal integrity. Layout should isolate gain-control routing and provide low-impedance decoupling for both ±5.25 V rails.
Recommandé
Broadband Signal Conditioning
The AD602JN is suitable for broadband signal conditioning when a subsystem must adjust amplitude without moving into a lower-frequency audio path. Its -3 dB bandwidth reaches 35 MHz, and the 1.4 nV/√Hz input noise density supports low-noise operation across that range. The linear-in-decibel gain response simplifies calibration when control values are mapped to dB rather than voltage. For wideband use, pay particular attention to gain-control bandwidth, output swing, component parasitics, and stable grounding around the 16-lead PDIP footprint.
Recommandé
Communications Receiver Front End
The AD602JN can provide adjustable gain in a communications receiver when incoming signal level varies substantially across operating conditions. Independent control of two channels supports receiver architectures that compare, balance, or process paired signals, while the -10 dB to +30 dB range gives the system authority to attenuate strong inputs and amplify weaker ones. Bandwidth up to 35 MHz covers many intermediate-frequency and wider-bandwidth signal paths. Choose the bias point carefully to retain distortion and bandwidth, and decouple the dual ±5.25 V supplies close to the device pins.
Recommandé
Test and Measurement Instrumentation
The AD602JN suits instrumentation requiring calibrated gain adjustment over a wide signal bandwidth. The 0.3 dB absolute-gain accuracy supports repeatable level setup, while two independently controlled channels can simplify source comparison or dual-path measurement systems. Its 35 MHz -3 dB bandwidth enables use beyond audio frequencies, and the 1.4 nV/√Hz noise density is valuable when the input source has low amplitude. Designers should account for control-voltage accuracy, output clipping, load impedance, and the frequency dependence of gain and distortion when establishing measurement limits.
Recommandé
Industrial Sensor Interface
The AD602JN can condition signals from industrial sensors whose output amplitude changes over time. The variable -10 dB to +30 dB gain range allows a controller to maintain a consistent downstream level, while 0.3 dB absolute-gain accuracy supports reproducible scaling. Its low 1.4 nV/√Hz input-noise density is useful for low-level sensing, and the two independent channels can support redundant or complementary sensor paths. Industrial implementations should verify EMI immunity, grounding strategy, control-voltage stability, and the operating-temperature requirements of the surrounding equipment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AD602JN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Consider the AD600JN when the required gain window is 0 dB to +40 dB. It retains the same dual-channel architecture and 16-lead PDIP format, making it the closest identified drop-in candidate, but the gain-control calibration must be revisited because its usable range is shifted upward by 10 dB. Before substituting either device, verify the complete pin assignments, control-voltage range, supply arrangement, output swing, distortion, and bandwidth at the intended operating point.
Comparaison avec les alternatives
| Paramètre | Ce produit | AD600JN |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 16-lead PDIP | 16-lead PDIP |
| Number of Channels | 2 channels | 2 channels |
| Gain Range | -10 dB to +30 dB | 0 dB to +40 dB |
| Gain Range Count | 2 ranges of 30 dB | 2 ranges of 30 dB |
| Gain Control Response | Linear in dB | Linear in dB |
Principaux différenciateurs
- Provides a usable negative-gain region (vs AD600JN)
- Two independent variable-gain channels (vs AD600JN)
- Wideband signal adjustment with linear-in-decibel control (vs AD600JN)
Notes de conception
Decouple both ±5.25 V rails independently and place the capacitors close to the device power pins. Keep the positive and return current paths short to reduce supply-related gain errors and prevent the dual supply architecture from introducing common-mode or differential noise into the high-bandwidth signal path.
Route the two gain-control inputs away from clock, switching-node, and high-current return paths. The linear-in-decibel control characteristic simplifies calibration, but only if the control voltage at the pins remains clean; excessive control-path noise can become gain modulation. Maintain a continuous ground reference around the 16-lead PDIP footprint.
Evaluate gain, distortion, and stability across the intended frequency range rather than relying only on the 35 MHz -3 dB bandwidth. Keep output loading compatible with the operating point, preserve adequate output swing, and verify that gain-control bandwidth supports the required settling time. Use the manufacturer electrical-characteristics tables for the final operating conditions.
Do not treat the AD602JN and AD600JN as identical during replacement. Their gain windows are shifted by 10 dB: -10 dB to +30 dB for the AD602JN and 0 dB to +40 dB for the AD600JN. Confirm gain-control polarity and voltage scaling, then recalibrate the system even when the package and pin arrangement remain unchanged.
Informations de conformité
The available product information identifies a commercial-grade component but does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for AD602JN.