AD705AZ - 100pA Input, 800kHz Op Amp | Analog Devices
Référence : AD705AZ ✗ Fin de vieAD705AZ Présentation
An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The AD705 belongs to the bipolar operational amplifier category, combining low input bias current with conventional precision-amplifier signal conditioning. Its low-current input stage is especially useful when the source resistance is high enough that input leakage could otherwise create a significant measurement error.
The AD705AZ provides 100 pA input current, 800 kHz gain bandwidth, 0.15 V/us slew rate, and 150 uV offset voltage. The 800 kHz bandwidth supports low-frequency closed-loop amplification, while the 0.15 V/us slew rate determines how rapidly the output can change under dynamic conditions. The 150 uV offset specification is particularly relevant when the amplifier operates near its input range and the measured signal is small.
This device uses a bipolar input architecture and is specified as a picoampere-input-current bipolar operational amplifier. Its practical performance depends on feedback topology, source impedance, supply voltage, operating frequency, and output loading. Because input current is a major error source in high-impedance systems, source resistance should be kept low enough that the amplifier input current does not dominate the signal developed across the source.
Typical uses include photodiode and sensor-interface amplification, low-current-to-voltage converters, precision laboratory instrumentation, and feedback networks in analog measurement equipment. It is also appropriate for applications requiring a general-purpose precision amplifier in an 8-pin through-hole ceramic package rather than a miniature surface-mount package.
Designers should begin by defining the closed-loop gain and required signal bandwidth, then confirm that the 800 kHz gain-bandwidth product provides adequate bandwidth and phase margin. The 0.15 V/us slew rate can become limiting for rapidly changing signals, so output settling and loading should be checked. High-impedance nodes also require guarded layouts, clean power grounding, and minimization of surface leakage.
This product record combines the verified AD705AZ operating characteristics with practical selection guidance, CERDIP-8 packaging information, source links, and engineering-focused considerations for low-current precision measurement.
Alternatives de remplacement direct pour AD705AZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesAD705AZ Valeurs maximales et caractéristiques électriques
| Amplifier Type | Precision operational amplifier |
| Number of Channels | 1 channel |
| Input Bias Current | 100 pA |
| Input Offset Voltage | 150 uV |
| Gain-Bandwidth Product | 800 kHz |
| Slew Rate | 0.15 V/us |
| Input Architecture | Bipolar input |
| Package Type | 8-pin CERDIP |
| Type de montage | Through-hole |
| Manufacturer | Analog Devices |
| Product Category | Operational amplifier |
| Typical Application | Precision signal conditioning |
| Statut RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
Guide de configuration des broches du AD705AZ 8-pin cerdip
Configuration des broches du AD705AZ (boîtier 8-pin cerdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AD705AZ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD705AZ convient pour 6 applications: Photodiode Signal Conditioning, Precision Sensor Interface, Low-Current-to-Voltage Conversion, Laboratory Instrumentation, Precision Feedback Control, Low-Level DC Amplification.
Photodiode Signal Conditioning
The AD705AZ fits low-level photodiode and phototransistor signal-conditioning circuits because its specified input current is only 100 pA. This low-current input stage limits the bias-generated error that can become significant when the sensor impedance is high. Its 800 kHz gain-bandwidth product and 0.15 V/us slew rate support modest-bandwidth precision measurements rather than high-speed photodiode extraction. The amplifier is normally used with a high-value feedback resistor, followed by an offset and gain stage as required. Layout should use guarded input traces, clean ground references, and minimal exposed-area contamination because board leakage can undermine the benefit of the 100 pA specification.
Precision Sensor Interface
The AD705AZ is appropriate for high-impedance sensor interfaces where the sensor output must be amplified without excessive input-loading error. Its 100 pA input current is the central benefit when the source resistance is large, while the 150 uV input offset voltage helps preserve accuracy for small sensor signals. The 800 kHz gain-bandwidth product is suitable for slowly varying process, temperature, and position measurements, and the 0.15 V/us slew rate limits how quickly large output transitions can occur. Designers should calculate the bias-current error across the actual source resistance and use guarding or differential wiring to reduce leakage and interference at the input node.
Low-Current-to-Voltage Conversion
The AD705AZ can form the input stage of a low-current-to-voltage converter when the converter must operate close to the amplifier's 100 pA input-current specification. A transimpedance feedback network converts sensor current into voltage, allowing the amplifier's bipolar input architecture to provide low-current measurement capability. Its 800 kHz gain-bandwidth product sets an upper bound for the useful closed-loop bandwidth, and the 0.15 V/us slew rate must be sufficient for the expected output changes. Because parasitic capacitance at a high-impedance summing node can destabilize the loop, the feedback resistor and compensation strategy should be evaluated together using the Analog Devices AD705 datasheet.
Laboratory Instrumentation
The AD705AZ is suitable for precision laboratory instrumentation that combines relatively high source impedance with modest signal bandwidth. The 100 pA input current reduces bias error in buffer and gain stages, the 150 uV offset specification supports low-level measurement accuracy, and the 800 kHz gain-bandwidth product accommodates slowly varying laboratory signals. Its 0.15 V/us slew rate also defines the large-signal settling capability. In an instrument design, preserve the advantage of low input current by using clean relay contacts, guarded PCB traces, stable reference components, and a low-leakage enclosure around sensitive nodes.
Precision Feedback Control
The AD705AZ can be used in a precision feedback loop when the error amplifier must sense a high-impedance node while driving only moderate bandwidth. Its 100 pA input current helps prevent the amplifier input from materially disturbing the feedback node, and its 800 kHz gain-bandwidth product can support loop compensation within a relatively slow control system. The 150 uV offset voltage may contribute to static control error, so it should be included in the error budget. The 0.15 V/us slew rate limits how rapidly the output can respond to error excursions. Stable operation requires evaluating loop gain, phase margin, output loading, and compensation using the device characteristics in the Analog Devices AD705 datasheet.
Low-Level DC Amplification
The AD705AZ fits low-level DC amplification where signal amplitude is small and source impedance is high. The 150 uV input offset voltage is the principal static-error metric, while the 100 pA input current limits leakage-induced error across high resistances. The 800 kHz gain-bandwidth product allows closed-loop gains to be selected according to signal bandwidth and stability requirements, and the 0.15 V/us slew rate governs large-signal capability. For best operation, use low-leakage feedback components, avoid long unprotected input traces, and establish the common-mode and output-voltage limits from the Analog Devices AD705 datasheet before final component selection.
Données de référence d'ingénierie pour AD705AZ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 8-pin CERDIP |
| Brand | Analog Devices |
| Number of Channels | 1 channel |
| Input Current | 100 pA |
| Input Offset Voltage | 150 uV |
| Gain-Bandwidth Product | 800 kHz |
| Slew Rate | 0.15 V/us |
| Input Architecture | Bipolar |
Principaux différenciateurs
- Very low input current for precision measurement (vs General-purpose 8-pin operational amplifiers)
- Offset and dynamic performance suited to low-level signals (vs Higher-bandwidth precision amplifiers)
- Legacy ceramic through-hole package (vs Surface-mount precision amplifiers)
Notes de conception
Calculate bias-current error from the actual source resistance before selecting the gain configuration. The AD705AZ input current is 100 pA, which produces 100 mV of error across a 1 Gohm source before amplification or offset correction. Use the exact input-current conditions from the Analog Devices AD705 datasheet, and avoid long, unprotected input traces because contamination-related board leakage can exceed the specified input current.
Guard the inverting input and feedback-resistor junction when using high-value impedances. Keep the sensitive node physically small, remove flux and contamination after assembly, and avoid routing the guard near unrelated high-impedance or switching nodes. This is particularly important because the AD705AZ's 100 pA input current provides little margin against leakage from contaminated board surfaces or humidity.
Check both bandwidth and slew rate for the intended signal. The 800 kHz gain-bandwidth product limits closed-loop bandwidth, while the 0.15 V/us slew rate limits large-signal transitions and output settling. For transimpedance use, evaluate feedback capacitance and node capacitance together because parasitic capacitance at the summing junction can alter stability even when the nominal bandwidth appears adequate.
Use an 8-pin CERDIP footprint based directly on the manufacturer pin-description table and verify the package orientation, notch, and pin-1 location against the physical drawing. The generic diagram library does not include the ceramic DIP variant, so do not rely on a visually similar package footprint without checking lead spacing, row width, and pin numbering.
Informations de conformité
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the AD705AZ.