AD7482AST - 12-Bit 3 MSPS SAR ADC | Analog Devices
Référence : AD7482AST ✓ ActifAD7482AST Présentation
An ADC is an analog-to-digital converter that transforms a continuously varying input voltage into a numeric value suitable for digital processing. The AD7482 belongs to the successive-approximation ADC family, where a sampling circuit, internal comparator, and successive conversion process determine the digital result. Its architecture provides a straightforward parallel data path for systems that need predictable conversion timing and direct connection to digital control logic.
Key features include 3 MSPS throughput, 12-bit resolution, a wide 40 MHz input bandwidth, and low power consumption of 90 mW in full-power mode. The device also supports a 2.5 mW nap mode and a standby mode with a maximum current of 2 A. Two parallel interface modes allow the converter to be used in systems with different digital timing requirements. The on-board 2.5 V reference can be replaced by an external reference source when greater system-level control is needed.
The internal track-and-hold circuit can handle input frequencies in excess of 40 MHz, making the AD7482AST useful for high-speed sampling rather than only slow instrumentation signals. The conversion process has no pipeline delay, which simplifies timing analysis compared with a multistage pipeline ADC. The nominal analog input range is 0 V to 2.5 V, while the offset-shift capability allows the nominal range to be moved by plus or minus 200 mV.
Typical applications include industrial control and data-acquisition systems, test and measurement equipment, communications infrastructure, medical instrumentation, and embedded signal-processing platforms. The 3 MSPS conversion rate is useful for sampling waveforms, monitoring analog sensors, and digitizing control signals. The parallel interface requires careful PCB routing and consideration of the number of digital output lines used by the surrounding controller.
Designers should pay particular attention to input impedance, source settling, reference stability, and timing margins around the 3 MSPS operating rate. The input network should preserve the 40 MHz bandwidth requirement when higher-frequency signals are sampled. Power and ground distribution should be arranged to prevent reference or analog-signal corruption, particularly when the converter is operated close to its maximum throughput.
This product page combines the AD7482AST electrical characteristics, package information, interface considerations, typical applications, and available drop-in family references. It is intended to help engineers evaluate the converter for high-speed data acquisition and to plan the PCB, power, signal, and timing requirements before integrating the ADC.
Alternatives de remplacement direct pour AD7482AST — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec AD7482AST (même facteur de forme et même empreinte) — différant par Package.
AD7482ASTZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD7482BST
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →AD7482BSTZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD7482AST Valeurs maximales et caractéristiques électriques
| ADC Type | Successive-approximation ADC |
| Résolution | 12 bit |
| Maximum Throughput Rate | 3 MSPS |
| Input Channels | 1 channel |
| Input Bandwidth | 40 MHz |
| Tension d'alimentation | 5 V maximum single supply |
| On-Board Reference | 2.5 V |
| Nominal Analog Input Range | 0 V to 2.5 V |
| Offset Shift Range | plus or minus 200 mV |
| Full-Power Consumption | 90 mW |
| Nap Mode Consumption | 2.5 mW |
| Standby Current | 2 A maximum |
| Interface | Parallel |
| Interface Modes | 2 parallel interface modes |
| Pipeline Delay | None |
| Boîtier | 48-pin LQFP |
| Package Dimensions | 7 mm x 7 mm |
| Type de montage | Surface mount |
Guide de configuration des broches du AD7482AST 7 mm x 7 mm
Configuration des broches du AD7482AST (boîtier 7 mm x 7 mm). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AD7482AST.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD7482AST convient pour 6 applications: Industrial Data Acquisition, Test and Measurement Equipment, Communications Signal Capture, Medical Monitoring Systems, Embedded Control Systems, Power and Process Monitoring.
Industrial Data Acquisition
The AD7482AST fits industrial data-acquisition systems that need rapid conversion of analog process signals without pipeline delay. Its 3 MSPS maximum throughput rate supports dense sampling of control, sensor, and instrumentation waveforms, while the 12-bit resolution provides 4096 digital codes for the nominal 0 V to 2.5 V input range. The parallel interface can connect efficiently to a controller or capture logic when timing is planned carefully. The 40 MHz input bandwidth also gives designers margin for source settling and signal conditioning. Use the internal 2.5 V reference for simplicity, or evaluate an external reference when system-level calibration requires common reference tracking. The principal design consideration is preserving settling time and reference integrity across repeated acquisitions.
Recommandé
Test and Measurement Equipment
The AD7482AST is appropriate for oscilloscope-like, signal-analysis, and automated test equipment requiring predictable parallel conversion timing. At rates up to 3 MSPS, the successive-approximation architecture can sample repetitive or transient signals without the pipeline delay of a pipelined converter, simplifying acquisition-window calculations. The 12-bit result and 40 MHz input bandwidth are useful for digitizing medium-bandwidth waveforms after suitable input conditioning. Designers should place the sampling network close to the ADC, keep analog and digital return paths separated, and verify that the selected front end settles within the available acquisition interval. The single 5 V supply architecture helps reduce board-level power complexity.
Recommandé
Communications Signal Capture
The AD7482AST can support communications signal-capture modules that convert received analog information into parallel digital data. Its 3 MSPS throughput is suitable for moderate-rate envelope, IF, or baseband sampling when the selected architecture does not require a faster converter. The wide 40 MHz input bandwidth allows the analog path to preserve higher-frequency components, but the complete system must still meet sampling and anti-aliasing requirements. The no-pipeline-delay characteristic can simplify synchronization between the converter clock and capture logic. Engineers should use short analog traces, a quiet reference connection, and controlled clock distribution to prevent timing or coupling problems from limiting the usable dynamic range.
Recommandé
Medical Monitoring Systems
The AD7482AST can serve in medical monitoring modules that digitize low-bandwidth physiological or diagnostic sensor signals where 12-bit resolution and a moderate conversion rate are sufficient. The 0 V to 2.5 V nominal input range and plus or minus 200 mV offset-shift capability can simplify front-end scaling around a single-supply signal. A 3 MSPS conversion capability allows the converter to oversample some slower sensors, although system-level anti-aliasing and clinical validation remain essential. The parallel output reduces the need for a serial ADC interface but increases routing requirements. Care should be taken with grounding, shielding, and isolation so that switching activity and external noise do not compromise measurement integrity.
Recommandé
Embedded Control Systems
The AD7482AST is useful in embedded controllers that acquire several analog channels sequentially or monitor rapidly changing control feedback. Its no-pipeline-delay operation provides a straightforward conversion event for a deterministic control loop, while the 12-bit resolution supports common position, pressure, and current measurements after suitable conditioning. The parallel bus must be mapped carefully to the processor or programmable logic, and unused outputs should be handled according to the manufacturer interface guidance. Designers can use the nap mode between bursts to reduce average power, but the controller must preserve the timing contract required for wake-up and the next conversion. Reference accuracy and source settling remain central to achieving repeatable results.
Recommandé
Power and Process Monitoring
The AD7482AST can be applied to power-supply and process-monitoring systems that need frequent numerical readings from conditioned analog nodes. A 3 MSPS rate allows short conversion windows and supports oversampling when the monitored quantity changes more quickly than the final filtering bandwidth. The 12-bit conversion resolution and 2.5 V nominal input range are suitable for many scaled voltage measurements, while the parallel interface enables direct transfer to monitoring logic. The analog input must be protected against transients and kept within the converter's permitted range. In addition, the reference and ground architecture should be designed so that switching converters and high-current traces do not inject errors into the sampled result.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AD7482AST — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | AD7482ASTZ | AD7482BST | AD7482BSTZ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-pin LQFP | 48-pin LQFP - same | 48-pin LQFP - same | 48-pin LQFP - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Throughput Rate | 3 MSPS | 3 MSPS | 3 MSPS | 3 MSPS |
| ADC Architecture | Successive-approximation ADC | Successive-approximation ADC | Successive-approximation ADC | Successive-approximation ADC |
| Input Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Input Bandwidth | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Interface | Parallel | Parallel | Parallel | Parallel |
| Supply Voltage | 5 V maximum single supply | 5 V maximum single supply | 5 V maximum single supply | 5 V maximum single supply |
| Pipeline Delay | None | None | None | None |
Principaux différenciateurs
- Documented same-package order-code substitution (vs AD7482ASTZ)
- No-pipeline-delay conversion timing (vs AD7482BST)
- High-speed input capability (vs AD7482BSTZ)
- Flexible reference implementation (vs AD7482BSTZ)
Notes de conception
Place the AD7482AST analog input and reference connections close to the device, and keep the parallel output routes away from the input and reference pins. Use a continuous ground plane with careful partitioning between analog and digital return currents. The 48-pin LQFP footprint requires attention to escape routing, but placing the converter before long parallel traces helps reduce loading and timing risk.
Treat the 40 MHz input bandwidth as a system requirement rather than an isolated converter specification. Select an input driver with adequate output impedance and verify that the source settles during the converter's acquisition interval. Short traces, a small return path, and appropriately placed bypass capacitors reduce distortion and conversion error. Use the manufacturer test circuit and recommended component values when matching performance at 3 MSPS.
Decouple the single 5 V supply close to the converter and route the current return directly to the device ground. Keep reference and analog-supply paths quiet because switching noise at the 2.5 V reference or input node can reduce conversion accuracy. The 90 mW full-power figure does not include every system-level loss, so validate the complete supply network for voltage margin and ripple under the intended acquisition duty cycle.
Do not confuse AD7482AST with a related order code without checking its exact suffix. The AD7482ASTZ, AD7482BST, and AD7482BSTZ variants appear in the same package family, but order-code semantics and temperature-grade requirements should be verified before substitution. Also avoid assuming that the 3 MSPS rate is usable if the source network cannot settle; timing margin must include the complete analog path.
Informations de conformité
Compliance fields are not stated in the manufacturer or distributor listings associated with this product. The analog product category and surface-mount package do not establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.