Analog Devices

AD8001ARZ - 800MHz Current Feedback Amplifier | Analog Devices

Référence : AD8001ARZ ✓ Actif
±5 V Vdss 5.5 mA at ±5 V Id 8-pin SOIC Package
MOQ : 1 |

AD8001ARZ Présentation

The Analog Devices AD8001ARZ is a low-power, high-speed current-feedback operational amplifier with 800 MHz bandwidth and 1200 V/µs slew rate, housed in an 8-pin SOIC package. It is designed for video, instrumentation, and general-purpose broadband signal chains operating from ±5 V, with dual supplies up to ±6 V or single supplies from 6 V to 12 V.

A current-feedback amplifier is a voltage-feedback amplifier alternative optimized for high-speed closed-loop gain stages. Its feedback network uses a balanced impedance rather than relying on the high-frequency behavior of a single input capacitance. This architecture supports wide bandwidth and high slew rate while maintaining useful gain at frequencies where conventional voltage-feedback amplifiers often lose bandwidth. The AD8001 therefore belongs to the operational-amplifier, analog-signal-conditioning, and broader semiconductor hierarchies.

Key characteristics include transimpedance linearization circuitry, low power consumption of approximately 50 mW, and a maximum supply current of 5.5 mA when operating from ±5 V. According to the Analog Devices product information, the device can deliver more than 70 mA of load current. Its current-feedback topology is intended to provide good differential gain and phase performance when driving video loads, while the linearization circuitry helps control the nonlinearities normally associated with current-feedback amplifiers.

The AD8001 can operate with dual power supplies up to ±6 V or with a single supply from 6 V to 12 V. Its 800 MHz bandwidth makes it suitable for video amplification, photodiode preamplification, signal conditioning, high-speed instrumentation, and general-purpose RF-adjacent circuits. An industrial-temperature version is specified from -40°C to +85°C, and an AD8001-EB evaluation board is available for laboratory verification.

When designing around the AD8001ARZ, verify the feedback resistor and compensation capacitor against the target closed-loop gain because current-feedback bandwidth and stability depend on those external components. Keep feedback and signal traces short, use low-inductance decoupling close to the supply pins, and observe the device's absolute maximum supply ratings.

This page combines the manufacturer's technical specifications with a focused drop-in family comparison, application guidance, package details, and practical design notes. It is intended to help engineers evaluate the AD8001ARZ quickly while still confirming the final circuit against the Analog Devices AD8001 data sheet.

Alternatives de remplacement direct pour AD8001ARZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

AD8001AR

✅ Remplacement direct
📦 8-pin SOIC
Same AD8001 family, 800 MHz bandwidth, 1200 V/µs slew rate, and 8-pin SOIC package; ordering suffix differs

📋 Alternative de référence (hors catalogue)

AD8001ARZ Valeurs maximales et caractéristiques électriques

Amplifier Type Current-feedback operational amplifier
Number of Circuits 1 circuit
Bandwidth 800 MHz
Slew Rate 1200 V/µs
Nominal Dual Supply ±5 V
Maximum Dual Supply ±6 V
Single Supply Range 6 V to 12 V
Maximum Supply Current 5.5 mA at ±5 V
Power Consumption 50 mW
Output Current Capability Over 70 mA
Output Load Capability Video loads
Linearization Circuitry Transimpedance linearization
Plage de température de fonctionnement -40°C to +85°C
Boîtier 8-pin SOIC
Type de montage Surface mount
Evaluation Board AD8001-EB

Guide de configuration des broches du AD8001ARZ 8-pin soic

Configuration des broches du AD8001ARZ (boîtier 8-pin soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 8-pin soic pour le AD8001ARZ

Aucune donnée de brochage détaillée disponible pour AD8001ARZ.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

AD8001ARZ convient pour 6 applications: Video Signal Conditioning, Photodiode and Optical Front Ends, High-Speed Instrumentation, Portable Battery-Powered Equipment, Analog-to-Digital Interface Preamp, Broadband Buffering and Active Termination.

📺

Video Signal Conditioning

The AD8001ARZ fits video amplification stages requiring high bandwidth and fast edge rates without moving into a much higher-power amplifier class. Its 800 MHz bandwidth and 1200 V/µs slew rate provide useful headroom for composite, component, or broadband video signals, while the transimpedance linearization circuitry supports improved differential gain and phase behavior into video loads. A gain of two with feedback around 499 Ω and a compensating capacitor around 2 pF is a useful starting point, but the final values must be taken from the manufacturer data sheet and checked against the required source and load impedance.

📷

Photodiode and Optical Front Ends

The AD8001ARZ is appropriate for high-speed transimpedance front ends because its current-feedback architecture and transimpedance linearization circuitry can support fast, low-power signal acquisition. The 800 MHz bandwidth supports high-value photodiode signals, while the 1200 V/µs slew rate helps preserve rise and fall times through the amplifier stage. Because transimpedance designs are strongly affected by photodiode capacitance, the feedback resistor, compensation capacitor, and layout must be optimized together; route the photodiode directly to the input and keep the feedback connection extremely short.

🖥️

High-Speed Instrumentation

The AD8001ARZ suits precision broadband measurement front ends where the 800 MHz bandwidth and 1200 V/µs slew rate must be reconciled with low power consumption of approximately 50 mW. It can be used as a gain stage ahead of a sampling or digitizing system, particularly where sensor outputs change rapidly and a slower amplifier would introduce excessive rise-time error. Maintain short, impedance-controlled input and feedback paths, and follow the data sheet's gain-dependent feedback recommendations because current-feedback stability depends on the external network rather than only on the closed-loop gain number.

📱

Portable Battery-Powered Equipment

The AD8001ARZ is well suited to compact, battery-powered instruments because it operates from a single 6 V to 12 V supply and consumes approximately 50 mW at ±5 V. Its 5.5 mA maximum supply current is low for an 800 MHz amplifier, while its ability to deliver more than 70 mA of load current supports downstream stages and termination networks. When designing the power tree, bypass the supply pins with very low-inductance capacitors and account for supply-current change when the amplifier drives a terminated video load or switches between operating states.

📊

Analog-to-Digital Interface Preamp

The AD8001ARZ can provide the high-speed gain immediately preceding an ADC when the converter requires a low-impedance drive and accurate edge preservation. Its 800 MHz bandwidth and 1200 V/µs slew rate help avoid slew-limited settling in front of a wideband sampling system, while its low-power operation benefits densely populated mixed-signal boards. The amplifier output must still satisfy the ADC's input-range, settling, and capacitive-loading requirements, and the feedback network should be selected from the manufacturer data sheet for the actual gain and termination arrangement.

🔧

Broadband Buffering and Active Termination

The AD8001ARZ can buffer or actively terminate signals in broadband test and measurement equipment where a passive line lacks sufficient drive strength. Its more than 70 mA output-current capability, 800 MHz bandwidth, and 1200 V/µs slew rate are useful when driving short cable runs or controlled termination networks. Stability still depends on the selected feedback components and the load presented to the output, so verify the exact load impedance and gain against the AD8001 data sheet before using the device as a general-purpose broadband buffer.

Récapitulatif des produits recommandés

AD8001-EB Evaluation board for verifying the amplifier circuit Utilisé dans : Video Signal Conditioning, Photodiode and Optical Front Ends, High-Speed Instrumentation, Portable Battery-Powered Equipment, Analog-to-Digital Interface Preamp, Broadband Buffering and Active Termination AD8018AR High-speed amplifier family option Utilisé dans : Video Signal Conditioning, High-Speed Instrumentation, Analog-to-Digital Interface Preamp AD8014ARZ Analog Devices Utilisé dans : Photodiode and Optical Front Ends OPA691ID Texas Instruments Utilisé dans : Portable Battery-Powered Equipment OPA694ID Texas Instruments Utilisé dans : Broadband Buffering and Active Termination
What is the AD8001ARZ bandwidth and slew rate?
The AD8001ARZ provides 800 MHz bandwidth and a 1200 V/µs slew rate. According to the Analog Devices AD8001 data sheet, these specifications make the device useful in general-purpose high-speed applications where large-amplitude, high-frequency signals must be reproduced without excessive distortion. The current-feedback architecture is the key implementation detail, since its closed-loop response depends on the external feedback network and gain-setting components.
What type of operational amplifier is the AD8001ARZ?
The AD8001ARZ is a single, low-power current-feedback operational amplifier. Analog Devices describes it as a low-power, high-speed amplifier with unique transimpedance linearization circuitry for driving video loads with good differential gain and phase performance. It is packaged in an 8-pin SOIC and is intended for instrumentation, video, and broadband signal-conditioning applications.
Which power supplies can the AD8001ARZ use?
The AD8001ARZ is designed for ±5 V operation, dual supplies up to ±6 V, or a single supply from 6 V to 12 V. The Analog Devices AD8001 data sheet identifies these supply configurations for high-speed applications. The appropriate choice depends on the signal-swing requirements, grounding arrangement, and the biasing strategy used by the surrounding circuit.
How much power does the AD8001ARZ consume?
The AD8001ARZ consumes approximately 50 mW and draws at most 5.5 mA from ±5 V supplies, according to Analog Devices. Its maximum supply current of 5.5 mA and capability to deliver more than 70 mA of load current make it suitable for portable, battery-powered, and compact high-speed instruments where amplifier power and board area are both constrained.
Where can I download the AD8001ARZ datasheet PDF?
The official AD8001 data sheet is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD8001.pdf. The manufacturer's AD8001 product page at https://www.analog.com/en/products/ad8001.html provides the package, temperature, evaluation-board, and product ordering information. Use the manufacturer PDF for pin connections, absolute maximum ratings, and recommended application circuits.
Where can I find the AD8001ARZ pinout?
The AD8001ARZ uses an 8-pin SOIC package, and its authoritative pin assignments are listed in the Pin Configuration and Pin Description sections of the Analog Devices AD8001 data sheet. Assign PCB nets directly from that table, particularly the supply, ground, input, output, and shutdown-related connections. The package diagram used on this page identifies the 8-pin SOIC outline, while the data sheet remains the controlling document for electrical connectivity.
What is the operating temperature range of the AD8001ARZ?
The AD8001ARZ is available in the industrial temperature range of -40°C to +85°C. Analog Devices identifies this range on the AD8001 product page and in the AD8001 data sheet. When using the device near the temperature limits, account for amplifier drift, the temperature coefficient of external feedback components, and the thermal performance of the SOIC package.
Can AD8001AR replace AD8001ARZ?
AD8001AR is an 8-pin SOIC member of the same AD8001 family and is a close electrical match to AD8001ARZ. The two listings both identify a single current-feedback amplifier in an 8-SOIC package, supporting pin-level substitution on an existing design. Confirm the orderable suffix, temperature grade, lifecycle condition, and production requirements before releasing a new design.
What is the best drop-in replacement for AD8001ARZ?
AD8001AR is the closest identified drop-in alternative because it uses the same 8-pin SOIC package and belongs to the same AD8001 current-feedback amplifier family. Its key electrical ratings are expected to remain aligned with AD8001ARZ. For a second-source strategy, use the AD8001 data sheet and the manufacturer's pin-compatibility guidance to verify the exact suffix, shutdown behavior, and supply requirements.
When should I choose AD8001ARZ over another high-speed amplifier?
Choose AD8001ARZ when the design needs a current-feedback amplifier with 800 MHz bandwidth, 1200 V/µs slew rate, approximately 50 mW power consumption, and operation from ±5 V. It is particularly useful for video and broadband conditioning circuits where the external feedback network can be tailored for the required closed-loop gain. Compare the selected gain-bandwidth point, stability, and output-current demand against the exact alternative being considered.
Is AD8001ARZ suitable for video amplifier applications?
Yes, the AD8001ARZ is suitable for video amplification because it provides 800 MHz bandwidth, 1200 V/µs slew rate, and transimpedance linearization circuitry for video loads. According to Analog Devices, this combination provides excellent differential gain and phase performance from a low-power circuit. The AD8001-EB evaluation board can be used to verify the intended video chain before committing to production.
What can replace AD8001ARZ in an existing PCB design?
AD8001AR can replace AD8001ARZ in an existing 8-pin SOIC layout because it is the same-family, non-Z ordering variant with the same package and amplifier function. Treat this as a board-level substitution rather than a blanket second-source approval: confirm the pin configuration, temperature grade, supply limits, and lifecycle status in the relevant manufacturer documentation.
AD8001ARZ vs AD8001AR - which is the better choice?
AD8001ARZ is the preferred orderable choice for a new design when its Pb-free-oriented ordering status matches your procurement requirements, while AD8001AR is the closely related 8-pin SOIC alternative. Both are listed as single current-feedback amplifiers in the 8-SOIC package. Compare the formal ordering information, automotive or environmental qualification requirements, and supply-chain status rather than relying only on the suffix.
What are the key specifications of AD8001ARZ that engineers should know?
The key AD8001ARZ specifications are 800 MHz bandwidth, 1200 V/µs slew rate, approximately 50 mW power consumption, 5.5 mA maximum supply current at ±5 V, and more than 70 mA load-current capability. The device uses current-feedback topology, includes transimpedance linearization, operates from -40°C to +85°C, and is offered in an 8-pin SOIC package.
Is there a Texas Instruments equivalent for AD8001ARZ?
The manufacturer-suggested cross-reference data identifies OPA691ID as a functional equivalent candidate, but functional equivalence is not the same as a guaranteed drop-in replacement. Confirm package pin compatibility, gain-versus-bandwidth behavior, supply range, stability, and output-current capability in the OPA691 data sheet before substituting it. For the closest board-level family match, prioritize AD8001AR and verify its ordering information.
How should I stabilize an AD8001ARZ gain stage?
Stabilize the AD8001ARZ gain stage by selecting the feedback resistor and compensation network for the required closed-loop gain, then validating them against the AD8001 data sheet's recommended values. Current-feedback amplifiers do not follow the same gain-bandwidth behavior as voltage-feedback devices, so copying a resistor from a conventional op-amp design can produce peaking or oscillation. Confirm the final network with simulation or the AD8001-EB evaluation board.

Données de référence d'ingénierie pour AD8001ARZ — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose AD8001ARZ for compact, high-speed video, instrumentation, photodiode, or broadband buffering circuits that need 800 MHz bandwidth, 1200 V/µs slew rate, and low power consumption. The transimpedance linearization circuitry and current-feedback architecture make it a good fit when the feedback network can be selected for the exact gain and load. AD8001AR is the closest family alternative for an existing 8-pin SOIC design, subject to confirming the ordering suffix and lifecycle requirements. The identified OPA691ID and OPA694ID entries are functional-equivalent candidates rather than confirmed drop-in replacements, so they require pin, stability, gain-bandwidth, supply, and load verification before use. For a new high-speed design, evaluate the AD8001ARZ with the AD8001-EB board and compare its measured settling, noise, and power performance against the complete system requirements.

Comparaison avec les alternatives

Paramètre Ce produit AD8001AR
Brand Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC
Amplifier Type Current-feedback operational amplifier Current-feedback operational amplifier
Bandwidth 800 MHz 800 MHz
Slew Rate 1200 V/µs 1200 V/µs
Nominal Dual Supply ±5 V ±5 V
Maximum Dual Supply ±6 V ±6 V
Single Supply Range 6 V to 12 V 6 V to 12 V
Maximum Supply Current 5.5 mA at ±5 V 5.5 mA at ±5 V
Power Consumption 50 mW 50 mW
Output Current Capability Over 70 mA Over 70 mA
Operating Temperature Range -40°C to +85°C -40°C to +85°C

Principaux différenciateurs

  • Combines very high bandwidth with low power (vs AD8001AR)
  • Current-feedback architecture with transimpedance linearization (vs AD8001AR)
  • Single-supply operation supports compact portable designs (vs AD8001AR)

Notes de conception

Do not treat the AD8001 as a conventional voltage-feedback amplifier and copy feedback values from a generic op-amp design. The closed-loop response of a current-feedback amplifier depends on the feedback resistor, compensation capacitor, gain, and load impedance. Start from the manufacturer data sheet's recommended values for the intended gain, then confirm peaking and settling with simulation or the AD8001-EB board.

Keep the input, output, and feedback paths physically short. Place the feedback resistor and compensation component immediately adjacent to the amplifier pins, use a continuous ground plane, and place low-inductance supply-bypass capacitors at the device. High-speed traces act as transmission lines at the 800 MHz operating bandwidth, so even a short routing error can create ringing, overshoot, or instability.

Estimated: with ±5 V supplies, a 5 mA supply current corresponds to approximately 50 mW of total supply power, consistent with the advertised 50 mW power consumption. Supply-current transients can be higher while driving a terminated video load, so size local decoupling for transient current as well as average current. Confirm the exact dissipation and operating-current behavior at the intended gain and load in the manufacturer data sheet.

Terminate outputs in the impedance expected by the connected video or instrumentation circuit and avoid long unterminated traces. The 1200 V/µs slew rate can produce large voltage excursions across an incorrect load, leading to ringing that is mistaken for amplifier instability. Compare the measured step response with the expected response of the selected feedback network before changing the device.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The manufacturer documentation identifies the AD8001ARZ as an industrial-temperature device, but the product information does not state RoHS, REACH, halogen-free, or conflict-minerals status. The ARZ ordering suffix should not be treated as standalone proof of lead-free status; confirm compliance in the manufacturer declaration or product-change documentation.

Données vérifiées le : 2026-11-18 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

ad8001arz reel7 AD8001ARZ datasheet AD8001ARZ datasheet pdf AD8001ARZ pinout AD8001ARZ 800MHz current feedback amplifier Analog Devices AD8001ARZ AD8001ARZ price AD8001ARZ stock AD8001ARZ equivalent AD8001ARZ replacement AD8001ARZ vs AD8001AR AD8001ARZ application circuit AD8001ARZ video amplifier AD8001ARZ 8-SOIC footprint

Composants & termes associés

Analog Devices AD8001ARZ AD8001AR AD8001-EB AD8014ARZ AD8018AR OPA691ID OPA694ID current-feedback amplifier operational amplifier analog signal conditioning high-speed amplifier transimpedance linearization 800 MHz bandwidth 1200 V/µs slew rate 50 mW power consumption video amplification photodiode preamplifier 8-pin SOIC SOIC package family surface-mount package high-speed instrumentation Analog Devices AD8001 data sheet
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ