AD8001ARZ - 800MHz Current Feedback Amplifier | Analog Devices
MPN: AD8001ARZ ✓ 啟用中AD8001ARZ 概覽
A current-feedback amplifier is a voltage-feedback amplifier alternative optimized for high-speed closed-loop gain stages. Its feedback network uses a balanced impedance rather than relying on the high-frequency behavior of a single input capacitance. This architecture supports wide bandwidth and high slew rate while maintaining useful gain at frequencies where conventional voltage-feedback amplifiers often lose bandwidth. The AD8001 therefore belongs to the operational-amplifier, analog-signal-conditioning, and broader semiconductor hierarchies.
Key characteristics include transimpedance linearization circuitry, low power consumption of approximately 50 mW, and a maximum supply current of 5.5 mA when operating from ±5 V. According to the Analog Devices product information, the device can deliver more than 70 mA of load current. Its current-feedback topology is intended to provide good differential gain and phase performance when driving video loads, while the linearization circuitry helps control the nonlinearities normally associated with current-feedback amplifiers.
The AD8001 can operate with dual power supplies up to ±6 V or with a single supply from 6 V to 12 V. Its 800 MHz bandwidth makes it suitable for video amplification, photodiode preamplification, signal conditioning, high-speed instrumentation, and general-purpose RF-adjacent circuits. An industrial-temperature version is specified from -40°C to +85°C, and an AD8001-EB evaluation board is available for laboratory verification.
When designing around the AD8001ARZ, verify the feedback resistor and compensation capacitor against the target closed-loop gain because current-feedback bandwidth and stability depend on those external components. Keep feedback and signal traces short, use low-inductance decoupling close to the supply pins, and observe the device's absolute maximum supply ratings.
This page combines the manufacturer's technical specifications with a focused drop-in family comparison, application guidance, package details, and practical design notes. It is intended to help engineers evaluate the AD8001ARZ quickly while still confirming the final circuit against the Analog Devices AD8001 data sheet.
直接替換替代品,適用於 AD8001ARZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD8001AR
✅ 直接替換📋 參考替代品(不在目錄中)
AD8001ARZ 最大額定值與電氣特性
| Amplifier Type | Current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Bandwidth | 800 MHz |
| Slew Rate | 1200 V/µs |
| Nominal Dual Supply | ±5 V |
| Maximum Dual Supply | ±6 V |
| Single Supply Range | 6 V to 12 V |
| Maximum Supply Current | 5.5 mA at ±5 V |
| Power Consumption | 50 mW |
| Output Current Capability | Over 70 mA |
| Output Load Capability | Video loads |
| Linearization Circuitry | Transimpedance linearization |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Evaluation Board | AD8001-EB |
AD8001ARZ 8-pin soic 腳位配置指南
AD8001ARZ(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD8001ARZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD8001ARZ 適用於 6 應用s: Video Signal Conditioning, Photodiode and Optical Front Ends, High-Speed Instrumentation, Portable Battery-Powered Equipment, Analog-to-Digital Interface Preamp, Broadband Buffering and Active Termination.
Video Signal Conditioning
The AD8001ARZ fits video amplification stages requiring high bandwidth and fast edge rates without moving into a much higher-power amplifier class. Its 800 MHz bandwidth and 1200 V/µs slew rate provide useful headroom for composite, component, or broadband video signals, while the transimpedance linearization circuitry supports improved differential gain and phase behavior into video loads. A gain of two with feedback around 499 Ω and a compensating capacitor around 2 pF is a useful starting point, but the final values must be taken from the manufacturer data sheet and checked against the required source and load impedance.
推薦
Photodiode and Optical Front Ends
The AD8001ARZ is appropriate for high-speed transimpedance front ends because its current-feedback architecture and transimpedance linearization circuitry can support fast, low-power signal acquisition. The 800 MHz bandwidth supports high-value photodiode signals, while the 1200 V/µs slew rate helps preserve rise and fall times through the amplifier stage. Because transimpedance designs are strongly affected by photodiode capacitance, the feedback resistor, compensation capacitor, and layout must be optimized together; route the photodiode directly to the input and keep the feedback connection extremely short.
推薦
High-Speed Instrumentation
The AD8001ARZ suits precision broadband measurement front ends where the 800 MHz bandwidth and 1200 V/µs slew rate must be reconciled with low power consumption of approximately 50 mW. It can be used as a gain stage ahead of a sampling or digitizing system, particularly where sensor outputs change rapidly and a slower amplifier would introduce excessive rise-time error. Maintain short, impedance-controlled input and feedback paths, and follow the data sheet's gain-dependent feedback recommendations because current-feedback stability depends on the external network rather than only on the closed-loop gain number.
推薦
Portable Battery-Powered Equipment
The AD8001ARZ is well suited to compact, battery-powered instruments because it operates from a single 6 V to 12 V supply and consumes approximately 50 mW at ±5 V. Its 5.5 mA maximum supply current is low for an 800 MHz amplifier, while its ability to deliver more than 70 mA of load current supports downstream stages and termination networks. When designing the power tree, bypass the supply pins with very low-inductance capacitors and account for supply-current change when the amplifier drives a terminated video load or switches between operating states.
推薦
Analog-to-Digital Interface Preamp
The AD8001ARZ can provide the high-speed gain immediately preceding an ADC when the converter requires a low-impedance drive and accurate edge preservation. Its 800 MHz bandwidth and 1200 V/µs slew rate help avoid slew-limited settling in front of a wideband sampling system, while its low-power operation benefits densely populated mixed-signal boards. The amplifier output must still satisfy the ADC's input-range, settling, and capacitive-loading requirements, and the feedback network should be selected from the manufacturer data sheet for the actual gain and termination arrangement.
推薦
Broadband Buffering and Active Termination
The AD8001ARZ can buffer or actively terminate signals in broadband test and measurement equipment where a passive line lacks sufficient drive strength. Its more than 70 mA output-current capability, 800 MHz bandwidth, and 1200 V/µs slew rate are useful when driving short cable runs or controlled termination networks. Stability still depends on the selected feedback components and the load presented to the output, so verify the exact load impedance and gain against the AD8001 data sheet before using the device as a general-purpose broadband buffer.
推薦
推薦產品摘要
工程參考資料,適用於 AD8001ARZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD8001AR |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Current-feedback operational amplifier | Current-feedback operational amplifier |
| Bandwidth | 800 MHz | 800 MHz |
| Slew Rate | 1200 V/µs | 1200 V/µs |
| Nominal Dual Supply | ±5 V | ±5 V |
| Maximum Dual Supply | ±6 V | ±6 V |
| Single Supply Range | 6 V to 12 V | 6 V to 12 V |
| Maximum Supply Current | 5.5 mA at ±5 V | 5.5 mA at ±5 V |
| Power Consumption | 50 mW | 50 mW |
| Output Current Capability | Over 70 mA | Over 70 mA |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C |
主要差異化特點
- Combines very high bandwidth with low power (對比AD8001AR)
- Current-feedback architecture with transimpedance linearization (對比AD8001AR)
- Single-supply operation supports compact portable designs (對比AD8001AR)
設計說明
Do not treat the AD8001 as a conventional voltage-feedback amplifier and copy feedback values from a generic op-amp design. The closed-loop response of a current-feedback amplifier depends on the feedback resistor, compensation capacitor, gain, and load impedance. Start from the manufacturer data sheet's recommended values for the intended gain, then confirm peaking and settling with simulation or the AD8001-EB board.
Keep the input, output, and feedback paths physically short. Place the feedback resistor and compensation component immediately adjacent to the amplifier pins, use a continuous ground plane, and place low-inductance supply-bypass capacitors at the device. High-speed traces act as transmission lines at the 800 MHz operating bandwidth, so even a short routing error can create ringing, overshoot, or instability.
Estimated: with ±5 V supplies, a 5 mA supply current corresponds to approximately 50 mW of total supply power, consistent with the advertised 50 mW power consumption. Supply-current transients can be higher while driving a terminated video load, so size local decoupling for transient current as well as average current. Confirm the exact dissipation and operating-current behavior at the intended gain and load in the manufacturer data sheet.
Terminate outputs in the impedance expected by the connected video or instrumentation circuit and avoid long unterminated traces. The 1200 V/µs slew rate can produce large voltage excursions across an incorrect load, leading to ringing that is mistaken for amplifier instability. Compare the measured step response with the expected response of the selected feedback network before changing the device.
合規資訊
The manufacturer documentation identifies the AD8001ARZ as an industrial-temperature device, but the product information does not state RoHS, REACH, halogen-free, or conflict-minerals status. The ARZ ordering suffix should not be treated as standalone proof of lead-free status; confirm compliance in the manufacturer declaration or product-change documentation.