AD9553BCPZ - 810MHz PLL Clock Translator | Analog Devices
Référence : AD9553BCPZ ✓ ActifAD9553BCPZ Présentation
A clock translator is a timing semiconductor that converts or redistributes reference frequencies while maintaining a controlled relationship between input and output signals. Clock translators occupy the clock-and-timing hierarchy alongside clock generators, buffers, multipliers, dividers, phase-locked loops, and jitter-control devices. The AD9553 uses a phase-locked loop to perform its frequency translation, allowing system designers to derive a required service or transport clock from an available reference rather than adding another dedicated oscillator.
The AD9553BCPZ provides a maximum listed operating frequency of 810 MHz and one output. Its integer-N PLL architecture accommodates the frequency-translation requirements associated with optical-access and telecommunications infrastructure. Two reference options broaden board-level flexibility: engineers may drive REFA and REFB separately with single-ended sources or use one differential reference arrangement. This makes the device useful in equipment where reference clocks originate from different upstream line cards or synchronization modules.
Its clock-generation role is especially relevant in base stations and passive optical networks, where accurate timing alignment affects downstream transport links and service synchronization. Ethernet, SONET/SDH, and T1/E1 equipment can also use programmable clock translation to reconcile reference-clock domains. The 32-LFCSP-WQ package supports compact placement in communications and networking hardware, although careful PCB layout and thermal management remain necessary for reliable high-frequency performance.
Typical deployments include GPON line terminals and central-office equipment, cellular base-station clocking, carrier Ethernet timing subsystems, optical transport modules, and telecommunications test equipment. In each case, the AD9553 is positioned between reference-clock sources and the timing distribution network, with configuration and loop-filter components determining the translation ratio and phase behavior.
The primary design consideration is the relationship between reference frequency, translation ratio, PLL loop bandwidth, output jitter, and the timing budget of the receiving equipment. Reference traces should be short and properly terminated, while power and ground planes should provide low-impedance return paths. Unused reference inputs require deliberate treatment rather than being left without a defined termination condition.
This product overview combines the manufacturer’s functional description with package, interface, and application guidance. It also identifies the engineering constraints that matter when planning a clock translator design, including reference selection, PLL configuration, high-frequency layout, and qualification of genuine drop-in alternatives rather than merely similar clock ICs.
Alternatives de remplacement direct pour AD9553BCPZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesAD9553BCPZ Spécifications
| Product Type | Integer-N PLL clock translator |
| Maximum Operating Frequency | 810 MHz |
| Output Count | 1 output |
| PLL Architecture | Integer-N phase-locked loop |
| Reference Input Configuration | Up to 2 single-ended inputs or 1 differential input |
| Reference Inputs | REFA and REFB |
| Boîtier | 32-LFCSP-WQ, 5 mm x 5 mm |
| Type de montage | Surface mount |
Guide de configuration des broches du AD9553BCPZ 32-lfcsp-wq, 5 mm x 5 mm
Configuration des broches du AD9553BCPZ (boîtier 32-lfcsp-wq, 5 mm x 5 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour AD9553BCPZ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD9553BCPZ convient pour 6 applications: GPON Passive Optical Network Timing, Cellular Base-Station Clocking, Carrier Ethernet Timing Translation, SONET/SDH Optical Transport, T1/E1 Line-Side Clocking, Telecommunications Test Equipment.
GPON Passive Optical Network Timing
The AD9553BCPZ fits GPON infrastructure because it translates an available reference clock through an integer-N PLL and can operate to 810 MHz. The device accepts two single-ended references on REFA and REFB or one differential reference, allowing the central-office design to reuse a synchronization source already distributed through the line-card architecture. Its single-output arrangement is appropriate when one translated clock must feed the next timing stage. Engineers should select the reference and divider values so that the resulting output meets the PON subsystem’s timing and jitter budget. The 32-LFCSP-WQ package also supports compact placement in line-terminal and central-office equipment, but differential routing, reference termination, and a continuous ground reference remain essential at high clock rates.
Recommandé
Cellular Base-Station Clocking
The AD9553BCPZ is suited to base-station timing because it provides an integer-N PLL-based translation function with a maximum operating frequency of 810 MHz. Instead of introducing another free-running oscillator for each internal clock domain, a base-station design can derive the required clock from an existing reference through REFA or REFB. The flexible single-ended and differential reference options support different synchronization architectures. With one output, the translated clock can feed the receiver, transmitter, or processing chain that requires it. Selection should be based on the resulting output frequency and jitter rather than the 810 MHz headline value alone, while PCB implementation must preserve short reference paths and an uninterrupted return path beneath the clock network.
Recommandé
Carrier Ethernet Timing Translation
The AD9553BCPZ can support carrier Ethernet equipment that needs a deterministic frequency relationship between a system reference and a downstream timing domain. Its integer-N PLL architecture performs clock translation to a maximum operating frequency of 810 MHz, while the flexible reference interface accepts either two single-ended sources or one differential clock. This allows synchronization to be routed from an existing timing hierarchy instead of requiring a dedicated converter at every interface. The single output is suitable for feeding a downstream transceiver, digital processing block, or clock-distribution stage. Practical design work should verify divider selection, reference phase alignment, output-jitter contribution, and termination of unused reference pins using the manufacturer’s guidance before treating the translated clock as a drop-in timing source.
Recommandé
SONET/SDH Optical Transport
The AD9553BCPZ is appropriate for SONET/SDH transport systems that reconcile a reference clock with the timing required by line-card circuitry. The part translates reference frequencies through an integer-N PLL and supports operation to 810 MHz, making it relevant to high-speed transport timing architectures. Two single-ended reference inputs or one differential reference provide flexibility in how the equipment receives synchronization from a higher-level network. Its one-output configuration supports a clean division of responsibility: the AD9553 creates the translated clock, and downstream distribution or transceiver circuitry fans it out. Board implementation should prioritize controlled impedance, short clock routes, solid plane connections, and proper treatment of an unused REFA or REFB input so that the PLL receives predictable reference conditions.
Recommandé
T1/E1 Line-Side Clocking
The AD9553BCPZ can be used in T1/E1 equipment when the line-card timing domain must be translated from a common system reference. Although the device is specified for communications-clock translation up to 810 MHz, its actual utility in a T1/E1 design depends on the selected reference, integer-N ratio, and resulting output-frequency accuracy. The flexible reference interface allows either separate single-ended sources or a differential reference to feed the PLL. A single translated output can then serve the line interface or a related timing block. Designers should evaluate phase behavior, jitter, reference noise, and loop stability against the line interface requirements rather than assuming the maximum frequency alone guarantees a timing-compatible solution.
Recommandé
Telecommunications Test Equipment
The AD9553BCPZ is useful in telecommunications test equipment that must synthesize a clock from a controlled reference while preserving a predictable frequency relationship. Its integer-N PLL architecture, operation to 810 MHz, and one-output configuration make it suitable for embedded timing-generation blocks in transport analyzers, interface testers, and line-card simulators. REFA and REFB can accept two single-ended sources or the circuit can use one differential reference, allowing the test instrument to accommodate multiple synchronization architectures. The compact 32-LFCSP-WQ package helps preserve instrument density. For dependable measurements, the reference source should be clean, the output configuration must meet the instrument’s jitter and phase requirements, and PCB layout should minimize clock-distribution loss before the signal reaches the test circuitry.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AD9553BCPZ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Brand | Analog Devices |
| Package | 32-LFCSP-WQ, 5 mm x 5 mm |
| Maximum Operating Frequency | 810 MHz |
| Output Count | 1 output |
| PLL Architecture | Integer-N PLL |
| Reference Input Configuration | Up to 2 single-ended inputs or 1 differential input |
| Reference Input Names | REFA and REFB |
| Target Applications | GPON, base stations, Ethernet, SONET/SDH, and T1/E1 |
Principaux différenciateurs
- Communications-specific integer-N clock translation (vs AD9553/PCBZ)
- Flexible reference architecture (vs AD9553/PCBZ)
- Application-targeted clock generation (vs Generic clock buffers)
Notes de conception
Route REFA, REFB, and the clock output over continuous reference planes and keep the loops formed by each clock trace and its return path as small as practical. The 810 MHz capability makes trace length, impedance continuity, connector transitions, and nearby switching-noise sources significant. Match the routing method to the PCB stack-up and use the manufacturer’s interface guidance for single-ended versus differential operation.
Do not leave an unused reference input without a defined termination condition. Analog Devices guidance for the AD9553 family describes AC-coupling the unused Reference B pin to ground with a 0.1 µF capacitor in the discussed single-ended Reference A configuration. Apply that technique only when it matches the actual clock arrangement, and confirm the final network against the manufacturer’s reference-input requirements before production.
Keep the PLL’s supply and ground connections clean because reference and output-jitter performance can be affected by supply noise and impedance paths around the package. Follow the manufacturer’s recommended decoupling arrangement and provide the lowest-inductance connection to ground available on the board. Avoid placing noisy switching regulators or high-current return paths immediately beneath sensitive clock nets unless the stack-up and return-current path have been evaluated.
Evaluate the complete reference path rather than only the nominal clock frequency. Source amplitude, edge rate, duty-cycle distortion, reference jitter, coupling, and termination all influence PLL behavior. Because the AD9553 uses an integer-N architecture, the translated output must be checked against the receiving circuit’s frequency and phase requirements, including any division ratio and loop bandwidth selected during configuration.
Informations de conformité
The available manufacturer page identifies the device and its communications applications but does not provide extractable RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.