ADC08B200CIVS - 8-bit 200MSPS ADC w/ Buffer | TI 48-TQFP
Référence : ADC08B200CIVS ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $13.5 | $13,50 |
| 10 | $12.1 | $121,00 |
| 100 | $10.65 | $1 065,00 |
| 500 | $9.4 | $4 700,00 |
| 1 000 | $8.25 | $8 250,00 |
ADC08B200CIVS Présentation
A high-speed analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous-time analog voltage into discrete digital codes at very high sample rates. ADCs sit at the boundary between the analog front-end and the digital processing block of a system and are organized in a hierarchy by resolution (8-bit, 10-bit, 12-bit, etc.) and sample rate. The 8-bit, 200 MSPS tier addresses applications such as video digitizers, digital oscilloscopes, IF sampling, and digital data-acquisition front ends where sub-ENOB resolution is acceptable in exchange for high throughput and low latency. ADC08B200 belongs to a class of pipeline ADCs internally followed by a small capture buffer that decouples the analog conversion rate from downstream memory bandwidth.
Key features of the ADC08B200CIVS include 200 MSPS guaranteed sampling rate, an internal 1K-sample FIFO capture buffer, single +3.0 V analog supply operation, and a straight-binary output format. The device also integrates a programmable duty-cycle stabilizer for the input clock and supports both external reference and internal reference modes. Differential and single-ended analog input topologies are accommodated through the on-chip input network.
The architecture combines a 8-bit flash-style quantizer with timing interpolation and an on-chip deep capture buffer that can hold up to 1024 conversion results. This lets a downstream processor read back conversions at a much slower clock than the ADC sample clock, simplifying PCB routing and relaxing memory bandwidth requirements in radar pulse, ultrasound, or pre-trigger oscilloscope architectures.
Typical applications include digital oscilloscopes, waveform digitizers, IF signal processing in communications receivers, radar pre-processing, CCD imaging systems, and consumer video capture. The 48-TQFP surface-mount package and industrial -40C to +105C temperature range make it suitable for both lab instruments and ruggedized field equipment.
When designing with ADC08B200CIVS, route the analog input with controlled-impedance 50 ohm traces and place the input coupling capacitors as close as possible to the device pins. The separate VDR output supply pin should be decoupled independently from the analog supply so switching noise on the digital outputs does not couple back into the analog front end.
This page synthesizes distributor pricing, drop-in compatible alternatives from the ADC08B200 family, and practical design notes drawn from the TI datasheet information not found on a single distributor listing.
Alternatives de remplacement direct pour ADC08B200CIVS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADC08B200CIVS (même facteur de forme et même empreinte) — différant par Architecture, Package, Resolution, Input Type, Operating Temperature Range.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC08B200CIVS/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC08B200QIVS
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ADC08B200CIVSX/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC081000CIYB
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$26.8 / unité
Voir la fiche technique →ADS8482IBRGZR
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$14.45 / unité
Voir la fiche technique →ADC12040CIVY
✅ Remplacement direct✓ En stock
$5.52 / unité
Voir la fiche technique →ADC08B200CIVS Valeurs maximales et caractéristiques électriques
| Résolution | 8 bits |
| Sample Rate | 200 MSPS |
| Number of Input Channels | 1 |
| Architecture | Pipeline / Flash with internal track-and-hold |
| Input Type | Single-ended / Differential (analog front end) |
| Capture Buffer Depth | 1024 samples (1K) |
| Digital Output Format | Straight binary, parallel CMOS/TTL |
| Analog Supply Voltage | 3.0 V typical |
| Output Supply Voltage (VDR) | 2.7 V to 3.3 V |
| Input Clock Feature | Programmable duty-cycle stabilizer |
| Plage de température de fonctionnement | -40C to +105C (industrial) |
| Boîtier | 48-pin TQFP (7x7 mm) |
| Type de montage | Surface Mount |
| Automotive Grade | AEC-Q100 Grade 2 (ADC08B200Q variant only, not CIVS) |
Configuration des broches de ADC08B200CIVS
| Broche 1 | VREF — Voltage reference input/output |
| Broche 2 | AGND — Analog ground |
| Broche 3 | AVIN — Analog input |
| Broche 4 | AGND — Analog ground |
| Broche 5 | VCCA — Analog supply voltage |
| Broche 6 | CLK — Clock input |
| Broche 7 | CLKB — Complementary clock input |
| Broche 8 | AGND — Analog ground |
| Broche 9 | OE — Output enable (active low) |
| Broche 10 | PD — Power down |
| Broche 11 | RESET — Reset / capture trigger |
| Broche 12 | DGND — Digital ground |
| Broche 13 | VCCD — Digital core supply |
| Broche 14 | DGND — Digital ground |
| Broche 15 | VDR — Digital output supply (2.7V-3.3V) |
| Broche 16 | DGND — Digital ground |
| Broche 17 | D0 — Data output bit 0 (LSB) |
| Broche 18 | D1 — Data output bit 1 |
| Broche 19 | D2 — Data output bit 2 |
| Broche 20 | D3 — Data output bit 3 |
| Broche 21 | D4 — Data output bit 4 |
| Broche 22 | D5 — Data output bit 5 |
| Broche 23 | D6 — Data output bit 6 |
| Broche 24 | D7 — Data output bit 7 (MSB) |
| Broche 25 | NC — Not connected (per datasheet) |
| Broche 26 | NC — Not connected (per datasheet) |
| Broche 27 | AGND — Analog ground |
| Broche 28 | AVIN — Analog input (differential pair) |
| Broche 29 | AGND — Analog ground |
| Broche 30 | VCCA — Analog supply voltage |
| Broche 31 | NC — Not connected (per datasheet) |
| Broche 32 | NC — Not connected (per datasheet) |
| Broche 33 | NC — Not connected (per datasheet) |
| Broche 34 | NC — Not connected (per datasheet) |
| Broche 35 | NC — Not connected (per datasheet) |
| Broche 36 | NC — Not connected (per datasheet) |
| Broche 37 | NC — Not connected (per datasheet) |
| Broche 38 | NC — Not connected (per datasheet) |
| Broche 39 | NC — Not connected (per datasheet) |
| Broche 40 | NC — Not connected (per datasheet) |
| Broche 41 | AGND — Analog ground |
| Broche 42 | AVINB — Complementary analog input |
| Broche 43 | AGND — Analog ground |
| Broche 44 | VCCA — Analog supply voltage |
| Broche 45 | VREF — Voltage reference |
| Broche 46 | AGND — Analog ground |
| Broche 47 | DGND — Digital ground |
| Broche 48 | VDR — Digital output supply (2.7V-3.3V) |
Applications typiques
ADC08B200CIVS convient pour 6 applications: Digital Storage Oscilloscope Front End, IF Signal Sampling in Communications Receivers, Radar and Lidar Pulse Capture, Ultrasound Beamforming Front End, CCD/CIS Imaging Digitizer, Industrial Test and Measurement Instrumentation.
Digital Storage Oscilloscope Front End
The ADC08B200CIVS fits digital oscilloscope front ends because its 200 MSPS sample rate captures repetitive and single-shot waveforms with bandwidths up to ~100 MHz and its integrated 1024-sample capture buffer decouples the 200 MSPS conversion clock from the host memory read clock. Placing the converter between the attenuator/probe amplifier and the FPGA display logic gives the trigger system up to 1024 samples of pre-trigger history without external FIFOs. The 48-TQFP package is footprint-compatible across the ADC08B200 family, letting designers swap the part for higher-speed or higher-resolution variants without PCB rework as requirements grow.
Recommandé
IF Signal Sampling in Communications Receivers
ADC08B200CIVS can directly digitize 70 MHz intermediate-frequency signals in digital receivers because the 200 MSPS sample rate comfortably exceeds twice the Nyquist rate of typical 70 MHz IF outputs. Engineers commonly place it after the final SAW filter and feed the digital output to a digital down-conversion block inside an FPGA or DSP. The straight-binary CMOS output format and the 2.7V-3.3V separate VDR supply pin let the ADC connect directly to a 3.3V FPGA without level shifters, simplifying the receiver BOM.
Recommandé
Radar and Lidar Pulse Capture
The integrated 1024-sample FIFO on the ADC08B200CIVS matches the requirement of pre-trigger radar pulse-capture channels, where the converter must digitize at the full 200 MSPS burst rate and then transfer samples into a slower processor at a much lower clock. Using the on-chip capture buffer eliminates external SRAM/FIFO parts and the associated PCB-routing complexity, which reduces noise coupling into the analog input. Designers typically clock the ADC with a low-jitter TCXO and feed the parallel output bus into an FPGA range-gate processor.
Recommandé
Ultrasound Beamforming Front End
Medical ultrasound beamformers benefit from the ADC08B200CIVS's combination of 200 MSPS throughput and low-latency digital output, which lets each receive channel digitize at rates compatible with 40 MHz transducer frequencies. The straight-binary CMOS output is well-suited to digital beamforming ASICs and FPGAs that perform delay-and-sum across many channels. The industrial -40C to +105C temperature range supports the thermal envelope of a densely populated multi-channel cart chassis.
Recommandé
CCD/CIS Imaging Digitizer
The ADC08B200CIVS serves as a high-speed video-rate digitizer for CCD and CMOS image-sensor readout pipelines where 8-bit resolution is acceptable per pixel and 200 MSPS aggregates multiple sensor channels into a single video data stream. The single-channel input and parallel CMOS output simplify routing in high-pixel-count line-scan cameras where the digitizer sits close to the sensor. Designers typically buffer the digital output into a frame buffer or transmit it via LVDS links to a host processor.
Recommandé
Industrial Test and Measurement Instrumentation
The ADC08B200CIVS suits data-acquisition modules in industrial test racks, including vibration analyzers, power-line transient recorders, and bench-top spectrum analyzers. The 200 MSPS rate oversamples wide-bandwidth signals sufficiently for envelope detection and FFT analysis, while the 8-bit resolution remains adequate for trigger and time-domain measurements. The 48-TQFP package and industrial -40C to +105C rating allow operation in factory-floor enclosures with minimal thermal management overhead.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADC08B200CIVS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC08B200CIVS/NOPB | ADC08B200QIVS | ADC08B200CIVSX/NOPB | ADC081000CIYB | ADS8482IBRGZR | ADC12040CIVY |
|---|---|---|---|---|---|---|---|
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP/QFN - verify pinout | 48-TQFP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 18 bits | 12 bits |
| Sample Rate | 200 MSPS | 200 MSPS | 200 MSPS | 200 MSPS | 1000 MSPS | 1 MSPS | 40 MSPS |
| Integrated Capture Buffer | 1024 samples | 1024 samples | 1024 samples | 1024 samples | No internal buffer | No internal buffer | No internal buffer |
| Automotive Qualified | No | No | Yes (AEC-Q100 Grade 2) | No | No | No | No |
| Analog Supply | 3.0 V | 3.0 V | 3.0 V | 3.0 V | 1.8 V/3.3 V | 5 V | 3.0 V |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C (AEC-Q100 G2) | -40C to +105C | -40C to +85C | -40C to +85C | -40C to +105C |
Principaux différenciateurs
- Integrated 1024-sample capture buffer eliminates external FIFO (vs ADC12040CIVY)
- Auto-grade variant available in identical 48-TQFP footprint (vs ADC08B200QIVS)
- Higher analog sample rate than typical 12-bit IF converters in same footprint (vs ADC12040CIVY)
Notes de conception
Route the analog input with controlled-impedance 50 ohm traces and place the input coupling capacitors as close as possible to the AVIN and AVINB pins. Keep the analog input traces symmetric to preserve the differential balance at high frequencies, since mismatch converts to common-mode noise and degrades SFDR. The AGND plane should be a continuous pour directly under the analog input network to shield against digital switching noise.
Decouple the VCCA analog supply with a low-ESR 10 uF tantalum or ceramic bulk capacitor and a 0.1 uF X7R high-frequency bypass located within 5 mm of each VCCA pin. Because the ADC08B200CIVS uses a separate VDR digital-output supply pin, place a ferrite bead between VDR and the noisy FPGA rail so output-driver switching noise does not back-propagate into the analog domain. Estimated: with five VCCA pins and standard decouplers, the regulator must source the device's typical analog current plus a 30 percent margin for transient bursts at full sample rate.
Do not rely on long output bus traces matched above 50 MHz; the 8-bit CMOS outputs toggle simultaneously at the sample rate, creating large simultaneous-switching-noise transients. Add 33 ohm series damping resistors on each output bit line near the ADC and provide a continuous digital ground return to the host FPGA. Failing to damp the output bus is a common cause of degraded SNR observed only at full 200 MSPS operation.
Informations de conformité
RoHS, REACH, lead-free, and halogen-free status were not in the Verified Web Data and are marked as unknown. The /NOPB suffix ordering variant is the Pb-free version of this part per TI conventions; the automotive-grade ADC08B200QIVS is AEC-Q100 Grade 2 qualified.