ADE9153AACPZ-RL - Single-Phase Auto-Calibrating Meter IC | ADI
Référence : ADE9153AACPZ-RL ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $5.8205 | $5,82 |
| 10 | $9.1323 | $91,32 |
| 100 | $9.1323 | $913,23 |
| 500 | $9.1323 | $4 566,15 |
| 1 000 | $9.1323 | $9 132,30 |
ADE9153AACPZ-RL Présentation
An energy-metering IC is a specialized data-acquisition and power-management component. In the measurement hierarchy, it sits between analog signal conditioning, analog-to-digital conversion, and the embedded processing that calculates real energy, RMS quantities, and related billing information. Unlike a general-purpose ADC, the ADE9153A family is configured for voltage and current channels used in electricity meters. Its autocalibration function can calibrate both channels when a shunt resistor is used as the current sensor, without requiring an accurate external source or reference meter.
The verified sources identify the ADE9153AACPZ-RL as a single-phase meter IC with auto-calibration. Analog Devices also offers the EV-ADE9153ASHIELDZ evaluation shield for prototyping energy-measurement systems. The shield includes a shunt resistor for line-current measurement and supports Arduino Uno, Arduino Zero, and ESP8266 platforms, with an Arduino library and application examples available from the product page. These resources make the device suitable both for production meter designs and early firmware evaluation.
The 32-LFCSP package requires careful PCB layout, exposed-pad thermal management, and short analog routing around the voltage and current inputs. Digital communication and supply decoupling paths should be separated from sensitive analog nodes to preserve measurement quality. Because the supplied data does not state accuracy, channel resolution, clock frequency, output interface, or absolute maximum ratings, those parameters must be confirmed in the manufacturer datasheet before schematic sign-off.
Typical uses include single-phase residential electricity meters, compact energy monitors, smart plugs, industrial sub-metering units, and Arduino-based measurement prototypes. The -40°C to 85°C range supports deployments across commercial and industrial ambient conditions, while the 2.97 V to 3.63 V supply range fits a regulated 3.3 V system. The -RL suffix and verified packaging references identify the tape-and-reel ordering option for automated assembly.
For a new design, use the Analog Devices evaluation shield and library to validate signal scaling, calibration behavior, and host-interface requirements before committing to a production board. In production, reproduce the manufacturer's recommended grounding, input filtering, exposed-pad, and decoupling layouts exactly where possible. This page combines verified distributor data, official evaluation resources, and engineering-focused selection guidance without inventing unprovided performance values.
Alternatives de remplacement direct pour ADE9153AACPZ-RL — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADE9153AACPZ-RL (même facteur de forme et même empreinte) — différant par Operating Temperature Range, Package, Product Type.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesADE9153AACPZ-RL Valeurs maximales et caractéristiques électriques
| Product Type | Single-phase energy-metering IC |
| Measurement Phase | 1 phase |
| Calibration Feature | Automatic current-channel and voltage-channel calibration |
| Supply Voltage Range | 2.97 V to 3.63 V |
| Plage de température de fonctionnement | -40°C to 85°C |
| Boîtier | 32-LFCSP, 5 mm x 5 mm |
| Alternative Package Description | 32-WFQFN exposed pad, CSP |
| Type de montage | Surface mount |
| Packaging Type | Tape and reel |
| Voltage Input | Mains line-voltage measurement channel |
| Current Input | Shunt-resistor line-current measurement channel |
| Autocalibration Requirement | No accurate source or accurate reference meter required when using a shunt resistor |
| Evaluation Accessory | EV-ADE9153ASHIELDZ |
| Evaluation Platform Support | Arduino Uno, Arduino Zero, ESP8266 |
| Software Support | Arduino library and application examples |
| Component Classification | Power Management IC |
| Functional Category | Data-acquisition ADC/DAC specialized meter IC |
Guide de configuration des broches du ADE9153AACPZ-RL 32-wfqfn exposed pad, csp
Configuration des broches du ADE9153AACPZ-RL (boîtier 32-wfqfn exposed pad, csp). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour ADE9153AACPZ-RL.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ADE9153AACPZ-RL convient pour 6 applications: Single-Phase Residential Electricity Meter, Smart Plug Energy Monitor, Industrial Sub-Metering Unit, Arduino-Based Energy Monitor, Compact Energy Monitoring Controller, Portable Energy Analyzer Prototype.
Single-Phase Residential Electricity Meter
The ADE9153AACPZ-RL fits a dedicated single-phase revenue meter because it combines voltage-channel and shunt-current measurement with automatic calibration. Its verified 2.97 V to 3.63 V supply range supports a regulated 3.3 V meter electronics section, while automatic gain calibration can reduce dependence on an accurate production source or reference meter. Place the sensitive current input close to its shunt and analog-ground network, isolate the mains sensing section, and validate calibration behavior over temperature and load. The 32-LFCSP package saves board area but requires exposed-pad land-pattern compliance and careful thermal review.
Recommandé
Smart Plug Energy Monitor
The ADE9153AACPZ-RL can support compact smart-plug energy monitoring when a shunt resistor measures line current and a protected divider senses line voltage. Its automatic calibration is useful in high-volume assemblies where reducing manual gain adjustment improves consistency. The verified 3.3 V-compatible supply range simplifies integration with embedded control logic, and the 5 mm by 5 mm LFCSP helps limit PCB area. However, the IC does not replace the fuse, surge protection, galvanic-isolation strategy, safety-approved enclosure, or regulatory validation required for a mains-connected product.
Recommandé
Industrial Sub-Metering Unit
For industrial single-phase sub-metering, the ADE9153AACPZ-RL provides a specialized metering front end with autocalibrated voltage and current channels. The verified -40°C to 85°C operating range covers many commercial and industrial environments, while automatic calibration can reduce per-unit alignment effort. The design should provide isolated sensing, surge protection, local regulation, and a communication interface appropriate to the installation. Engineers should confirm metering accuracy, channel bandwidth, clock requirements, and output protocol in the manufacturer documentation before selecting the part for billing-grade use.
Recommandé
Arduino-Based Energy Monitor
The ADE9153AACPZ-RL is well suited to an Arduino-based energy monitor because Analog Devices offers the EV-ADE9153ASHIELDZ with an onboard current shunt. The verified manufacturer information states compatibility with Arduino Uno, Arduino Zero, and ESP8266 platforms and provides an Arduino library plus application examples. This combination shortens firmware bring-up and lets developers evaluate scaling, readings, and calibration before designing a custom board. The shield should be treated as an evaluation platform, not as a substitute for production safety, isolation, and enclosure engineering.
Recommandé
Compact Energy Monitoring Controller
The ADE9153AACPZ-RL can serve as the measurement engine in a compact energy-monitoring controller that must acquire both voltage and line-current information. Its single-phase specialization avoids carrying unnecessary multiphase circuitry, and its 32-LFCSP package supports denser assemblies than larger leaded or high-pin-count meter packages. The verified supply range and broad operating-temperature interval support industrial control boards. Layout must keep switching regulators and digital interfaces away from the analog inputs, while firmware must confirm that autocalibration events are interpreted correctly by the host or display system.
Recommandé
Portable Energy Analyzer Prototype
The ADE9153AACPZ-RL is useful in a portable single-phase energy-analyzer prototype built around the Arduino ecosystem. The verified availability of a library and application examples for Arduino Uno, Arduino Zero, and ESP8266 accelerates data acquisition, while autocalibration helps simplify initial characterization of the voltage and shunt-current channels. Designers should use an appropriately protected, isolated sensing arrangement rather than exposing evaluation hardware to unrestricted mains energy. The 32-LFCSP footprint also supports compact prototypes, although layout should begin from Analog Devices' package and reference guidance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADE9153AACPZ-RL — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Brand | Analog Devices |
| Package | 32-LFCSP, 5 mm x 5 mm |
| Product Type | Single-phase energy-metering IC |
| Supply Voltage | 2.97 V to 3.63 V |
| Operating Temperature | -40°C to 85°C |
| Autocalibration | Voltage-channel and current-channel automatic calibration |
| Current-Sensing Method | Shunt resistor |
| Evaluation Platform | EV-ADE9153ASHIELDZ for Arduino Uno, Arduino Zero, and ESP8266 |
Principaux différenciateurs
- Integrated metrology purpose (vs General-purpose ADC)
- Production calibration simplification (vs Manually calibrated meter implementation)
- Compact dedicated package (vs Larger discrete energy-measurement front end)
Notes de conception
Keep the voltage and current inputs short, guarded, and away from switching nodes and high-current return paths. Follow the manufacturer's recommended analog grounding and exposed-pad land pattern; the supplied sources confirm a 32-LFCSP, 5 mm by 5 mm package but do not provide the full land pattern. Treat the mains divider and shunt network as high-energy, high-voltage nodes, and keep copper under the IC limited as required by the complete safety design.
Power the ADE9153A from a regulated source within the verified 2.97 V to 3.63 V range. Place local decoupling at the supply pins using the manufacturer's recommended capacitance and ESR characteristics, which are not provided in the supplied data and must be taken from the datasheet. Keep the analog supply return continuous through the exposed-pad region and isolate switching-node currents from the measurement reference path.
Do not assume that autocalibration eliminates the need for a sound shunt and voltage-divider design. Verify polarity, scaling, gain constants, calibration timing, and meter constants in firmware with known test conditions. The supplied search results confirm automatic calibration for voltage and current channels, but they do not provide accuracy limits, resolution, or calibration equations; obtain those values from the manufacturer datasheet before production use.
Informations de conformité
The supplied sources do not provide explicit compliance declarations. No compliance status has been inferred from the package, manufacturer, or distributor listings.
