Analog Devices

ADF4154BCPZ-RL7 - 4 GHz Fractional-N PLL Synthesizer | Analog Devices

Référence : ADF4154BCPZ-RL7 ✓ Actif
2.7 V to 3.3 V Vdss 2 selectable settings Id 20-WFQFN exposed-pad chip-scale package Package 4 GHz Speed
MOQ : 1 |

ADF4154BCPZ-RL7 Présentation

The Analog Devices ADF4154BCPZ-RL7 is a fractional-N frequency synthesizer for RF local-oscillator generation, with an RF input bandwidth up to 4 GHz, dual-modulus prescalers of 4/5 and 8/9, and a 3-wire serial programming interface. It is supplied in a 20-lead WFQFN exposed-pad chip-scale package for compact RF and microwave signal-chain designs.

A fractional-N frequency synthesizer is a phase-locked-loop device that generates precise local-oscillator signals for RF transmitters and receivers. The ADF4154 combines a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and a sigma-delta fractional interpolator. This architecture supports integer and fractional division ratios while preserving stable phase locking across programmable output frequencies.

The principal operating features include RF bandwidth to 4 GHz, a 2.7 V to 3.3 V power supply, programmable charge-pump currents, a separate VP tuning-voltage supply, digital lock detection, and power-down mode. The dual 4/5 and 8/9 prescalers extend the usable integer-N range, while the sigma-delta fractional interpolator enables fine frequency synthesis for wireless transceiver architectures.

The 3-wire serial interface provides a compact control path for programming divider ratios, prescaler selection, charge-pump settings, and power state. The device is designed for direct PCB integration where RF routing, grounding, decoupling, and exposed-pad thermal management are critical. Its separate VP connection allows the tuning-voltage range to be extended beyond the constraints imposed by the main supply when appropriate external circuitry and voltage limits are used.

Typical applications include wireless receiver and transmitter local oscillators, microwave up-converters and down-converters, frequency-agile test equipment, RF signal generators, radar-related signal chains, and industrial RF communication systems. In these systems, the synthesizer supplies a programmable reference for mixers or other RF conversion stages.

PCB design should minimize RF trace loss, maintain a continuous ground reference beneath the exposed pad, and place supply and decoupling connections close to their associated pins. Loop-filter components and the reference input should be positioned to avoid noisy digital-control coupling. The manufacturer datasheet is the controlling reference for register programming, pin assignments, recommended application circuits, and absolute operating limits.

This product page consolidates the verified device identity, package information, manufacturer documentation, operating features, sourcing guidance, and practical integration considerations. It also distinguishes true pin-compatible family alternatives from parts that require different packages or different synthesizer architectures, helping engineers evaluate replacement options without implying that every similar PLL is a drop-in replacement.

Alternatives de remplacement direct pour ADF4154BCPZ-RL7 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec ADF4154BCPZ-RL7 (même facteur de forme et même empreinte) — différant par Package, Charge Pump, Charge-Pump Current, Device Type, Lock Detect.

Analog Devices
Package: 20-VFQFN exposed-pad CSP, 3.75 mm × 4 mm
Charge Pump: Precision charge pump
Charge-Pump Current: Two selectable settings
Comparer avec ADF4154BCPZ-RL7 →
Analog Devices
Package: LFCSP-20 (4 mm × 4 mm) with exposed pad
Charge Pump: Precision charge pump with programmable current
Device Type: Fractional-N frequency synthesizer
Comparer avec ADF4154BCPZ-RL7 →
Analog Devices
Package: 20-lead LFCSP with exposed pad
Charge-Pump Current: Programmable
Lock Detect: Digital
Comparer avec ADF4154BCPZ-RL7 →

ADF4153BCPZ-RL7

✅ Remplacement direct
Analog Devices
📦 20-WFQFN exposed-pad chip-scale package
Fractional-N frequency synthesizer · 4 GHz · 1 · 2.7 V to 3.3 V · -40 °C to +85 °C · Three-wire external interface · External · Fractional-N

Contactez-nous pour le prix

Voir la fiche technique →

ADF4157BCPZ-RL7

✅ Remplacement direct
Analog Devices
📦 20-WFQFN exposed-pad chip-scale package
Fractional-N frequency synthesizer · 6 GHz · 25 bit · Sub-hertz at 6 GHz · 3.3 V · Separate supply for extended tuning voltage · Programmable · Programmable

Contactez-nous pour le prix

Voir la fiche technique →

ADF4154BCPZ-RL7 Spécifications

Device Type Fractional-N frequency synthesizer (RF) IC
Maximum RF Frequency 4 GHz
Minimum RF Frequency 200 MHz
Power-Supply Range 2.7 V to 3.3 V
Dual-Modulus Prescaler 4/5 and 8/9
Programmable Charge-Pump Currents 2 selectable settings
Control Interface 3-wire serial interface
Reference Input Logic CMOS
Type de sortie Clock
Number of Circuits 1
Input-to-Output Ratio 2:1
Differential Output No
Lock Detection Digital
Power-Down Mode Supported
Tuning Supply Separate VP connection
Boîtier 20-WFQFN exposed-pad chip-scale package
Type de montage Surface mount

Guide de configuration des broches du ADF4154BCPZ-RL7 20-wfqfn exposed-pad chip-scale package

Configuration des broches du ADF4154BCPZ-RL7 (boîtier 20-wfqfn exposed-pad chip-scale package). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 20-wfqfn exposed-pad chip-scale package pour le ADF4154BCPZ-RL7

Aucune donnée de brochage détaillée disponible pour ADF4154BCPZ-RL7.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

ADF4154BCPZ-RL7 convient pour 6 applications: Wireless Receiver Local Oscillator, Wireless Transmitter Up-Converter, Microwave Down-Converter, RF Signal Generator, Frequency-Swept Test Equipment, Industrial RF Communication Module.

🌐

Wireless Receiver Local Oscillator

The ADF4154BCPZ-RL7 fits a programmable receiver local-oscillator block that must cover RF channels approaching the device's 4 GHz upper bandwidth. Its 4/5 and 8/9 dual-modulus prescalers support the required integer division range, while the sigma-delta fractional interpolator enables fine channel spacing. The 3-wire interface minimizes control wiring, and digital lock detect supports system-level monitoring. A production design should verify reference phase noise, loop bandwidth, lock margin, and RF output power across the complete channel plan.

📡

Wireless Transmitter Up-Converter

In a transmitter up-conversion path, the ADF4154BCPZ-RL7 can generate a programmable local-oscillator signal for driving a mixer or subsequent RF stage. Its RF bandwidth to 4 GHz accommodates high-band transmitter plans, while programmable charge-pump currents allow the loop filter to be tuned for phase noise and acquisition performance. The separate VP connection supports extended tuning-voltage designs. Engineers should verify spur performance, output isolation, and compliance with the final transmitter mask using the complete reference and loop-filter design.

🌐

Microwave Down-Converter

The ADF4154BCPZ-RL7 is suitable for the programmable oscillator driving a microwave down-converter or receiver mixer. Operation to 4 GHz provides substantial tuning range for microwave links, while the fractional-N architecture supports precise channel selection. The 3-wire control interface reduces the logic-routing burden in compact RF modules. Layout must preserve short RF paths and a low-impedance ground plane, and the loop filter must be evaluated for both phase noise and the acquisition time required when changing channels.

🖥️

RF Signal Generator

The ADF4154BCPZ-RL7 can form the programmable frequency source in an RF signal-generator architecture where accurate channel selection and repeatable phase locking are required. Its programmable prescaler, charge-pump currents, and fractional interpolator permit the loop design to be adapted to different output frequencies. The digital lock-detect feature can supervise acquisition, while power-down mode supports controlled operating states. For laboratory-grade results, reference phase noise, RF output matching, and filter-component tolerances must be evaluated alongside the synthesizer.

📡

Frequency-Swept Test Equipment

The fractional-N capability of the ADF4154BCPZ-RL7 supports programmable swept or stepped excitation for RF test systems. The 4 GHz maximum RF bandwidth permits high-frequency test points, and the serial interface allows a controller to update divider and tuning parameters efficiently. Digital lock detect provides a signal that a test sequencer can use before accepting a measurement. Switching-time targets depend on loop bandwidth, reference frequency, prescaler choice, and filter design, so they should be measured rather than inferred from interface speed alone.

🏭

Industrial RF Communication Module

The ADF4154BCPZ-RL7 can provide a compact programmable oscillator for industrial RF communication equipment requiring channel selection and stable phase lock. The 20-WFQFN exposed-pad package supports dense RF board layouts, and the 3-wire interface minimizes control-signal count. Industrial equipment designers should account for temperature-dependent loop behavior, reference-source quality, and conducted or radiated emissions from the RF output network. The digital lock-detect output also helps the host controller distinguish an unlocked channel from an operating fault.

What is the ADF4154BCPZ-RL7?
The ADF4154BCPZ-RL7 is a 4 GHz fractional-N frequency synthesizer manufactured by Analog Devices. According to the ADF4154 manufacturer datasheet, it combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and sigma-delta fractional interpolator in a 20-WFQFN exposed-pad package. It is intended primarily for RF local-oscillator generation in wireless transmitters and receivers.
What is the operating voltage of ADF4154BCPZ-RL7?
The ADF4154BCPZ-RL7 operates from a 2.7 V to 3.3 V supply. According to the Analog Devices ADF4154 datasheet, the device also provides a separate VP connection that can support an extended tuning-voltage range. The main supply and tuning supply serve different functions, so the VP maximum voltage should be selected from the manufacturer guidance for the intended charge-pump and loop-filter configuration.
Where can I download the ADF4154BCPZ-RL7 datasheet PDF?
The official ADF4154 datasheet PDF is available from Analog Devices at the product datasheet link on this page. The document covers the 4 GHz RF bandwidth, 2.7 V to 3.3 V supply range, 4/5 and 8/9 prescalers, programmable charge-pump currents, 3-wire serial interface, digital lock detect, power-down mode, and family pin-compatibility information. Use the manufacturer document as the controlling reference for register programming and electrical limits.
Where can I find the ADF4154BCPZ-RL7 pinout?
The ADF4154BCPZ-RL7 pinout and pin descriptions are in the pin-configuration section of the official ADF4154 datasheet. The device uses a 20-WFQFN exposed-pad package, so the exposed thermal pad must also be connected according to the manufacturer land-pattern and assembly guidance. Use the package drawing and pin table together when assigning PCB nets and confirming exposed-pad thermal and ground requirements.
What is the best drop-in replacement for ADF4154BCPZ-RL7?
ADF4153BCPZ-RL7 is the closest verified same-family alternative because the ADF4154 manufacturer datasheet identifies the ADF4154 as pin-compatible with the ADF4153 and both use the same 20-WFQFN package family. Its upper RF frequency is lower than the ADF4154 maximum, so it should be selected only when the intended operating band remains within the ADF4153 limits. Confirm register compatibility and loop-filter recalculation before substitution.
Can ADF4153BCPZ-RL7 replace ADF4154BCPZ-RL7?
ADF4153BCPZ-RL7 can be considered a package-compatible replacement when the required output frequency is below the ADF4153 limit. The Analog Devices ADF4154 datasheet explicitly states pin compatibility with the ADF4153, and both devices use the 20-WFQFN format. Because the ADF4154 reaches 4 GHz while the ADF4153 has a lower maximum frequency, the replacement is only valid for RF plans that do not require the upper ADF4154 frequency range.
When should I choose ADF4154BCPZ-RL7 over ADF4153BCPZ-RL7?
Choose ADF4154BCPZ-RL7 when the design must synthesize at frequencies above the ADF4153 operating limit or approaches the ADF4154 maximum of 4 GHz. The two devices share the 20-WFQFN package and are identified as pin-compatible in the ADF4154 datasheet. For lower-frequency designs that fully satisfy the ADF4153 limits, the ADF4153 may reduce complexity, but existing firmware and loop-filter settings should still be reviewed.
What is the difference between ADF4154BCPZ-RL7 and ADF4153BCPZ-RL7?
The principal verified difference is the operating frequency range: the ADF4154 supports RF frequencies up to 4 GHz, while the ADF4153 has a lower maximum frequency. Both use the 20-WFQFN package, and the ADF4154 datasheet identifies the ADF4153 as pin-compatible. A replacement is therefore frequency-dependent and should also be checked for required feature, register, reference-input, and loop-filter compatibility.
Is ADF4154BCPZ-RL7 suitable for wireless receiver local oscillators?
Yes, the ADF4154BCPZ-RL7 is designed for programmable RF local oscillators used in wireless receiver and transmitter up-conversion and down-conversion paths. Its features include RF bandwidth to 4 GHz, programmable 4/5 and 8/9 dual-modulus prescalers, programmable charge-pump currents, and digital lock detection. The reference oscillator, loop filter, RF output network, and required frequency range must be designed together for reliable phase lock.
How does the ADF4154BCPZ-RL7 fractional-N architecture work?
The ADF4154 generates a controllable local-oscillator frequency by dividing a reference frequency with integer and fractional division ratios while correcting phase error through a phase-frequency detector and charge pump. Its sigma-delta fractional interpolator shapes the fractional-N division error, while the programmable prescalers support the required integer division range. The resulting loop behavior depends on reference frequency, prescaler, charge-pump current, loop-filter values, and output frequency.
Where can I buy ADF4154BCPZ-RL7 and check its lead time?
Use the Request a Quote form on this page to request current availability, unit pricing, minimum order quantity, and lead time for the exact ADF4154BCPZ-RL7 ordering code. The manufacturer product page identifies the ADF4154 as recommended for new designs, while distributor listings confirm the exact 20-WFQPN exposed-pad variant. Confirm reel packaging, authorized sourcing, and production quantities when placing the order.
Is ADF4154BCPZ-RL7 currently in stock?
Current stock for the exact ADF4154BCPZ-RL7 should be confirmed through the Request a Quote form on this page. Product listings identify the part as available for quotation, but inventory levels can change independently by region, quantity, and packaging. Submit the required quantity and target delivery date to obtain a current availability and lead-time response for the exact ordering code.
What determines the price of ADF4154BCPZ-RL7?
The price of ADF4154BCPZ-RL7 can depend on order quantity, production volume, packaging, authorized-channel availability, and requested delivery terms. Use the Request a Quote form on this page for current pricing rather than relying on a static marketplace value. Include the reel quantity, annual usage, target date, and whether a prototype or production schedule is needed so the quote reflects the intended purchasing profile.
Can ADF4154BCPZ-RL7 generate a 4 GHz local-oscillator signal?
The ADF4154 has an RF bandwidth up to 4 GHz, making it suitable for local-oscillator plans that operate at or near that upper limit. Actual usable output frequency also depends on the reference input, divider settings, prescaler, loop-filter design, charge-pump settings, RF matching, and output-buffer configuration. Validate lock margin and output power in the final reference and filter implementation rather than treating 4 GHz as a standalone guarantee for every channel plan.
What design considerations apply to the ADF4154BCPZ-RL7 loop filter and PCB?
The loop filter must be calculated for the target reference frequency, output frequency, prescaler, charge-pump current, phase-noise requirement, and lock-time objective. On the PCB, keep the RF output path short and controlled, provide a continuous ground reference, connect the exposed pad according to the manufacturer package guidance, and place bypass capacitors close to the supply pins. Isolate the reference and sensitive RF nodes from noisy 3-wire programming lines to reduce spurs and phase-noise coupling.
Are there five drop-in alternatives for ADF4154BCPZ-RL7?
Only two clearly verified same-package family alternatives were identified: ADF4153BCPZ-RL7 and ADF4157BCPZ-RL7. The Analog Devices ADF4154 datasheet documents pin compatibility with the ADF4153, and the ADF4157 comparison identifies the same 20-WFQCN package and pin-compatible family construction. No cross-brand drop-in equivalent was established with sufficient package, pinout, and parameter evidence, so unrelated PLL products and alternate packaging codes are not included.

Données de référence d'ingénierie pour ADF4154BCPZ-RL7 — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the ADF4154BCPZ-RL7 when the RF plan requires operation above the ADF4153's upper-frequency limit or needs the full 4 GHz bandwidth of the ADF4154 family. Its 4/5 and 8/9 prescalers, programmable charge-pump currents, digital lock detect, and separate VP connection support flexible fractional-N loop design. Consider ADF4153BCPZ-RL7 when every required channel stays below its upper limit and its documented pin compatibility permits a board-level transition. Consider ADF4157BCPZ-RL7 after checking its frequency range and functional requirements against the target design. No cross-brand drop-in substitute should be assumed solely because another PLL also covers the GHz range. For every option, recheck the reference frequency, prescaler, loop-filter values, register map, output configuration, RF layout, and exposed-pad assembly requirements before production release.

Comparaison avec les alternatives

Paramètre Ce produit ADF4153BCPZ-RL7 ADF4157BCPZ-RL7
Package 20-WFQFN exposed-pad chip-scale package 20-WFQFN exposed-pad chip-scale package 20-WFQCN exposed-pad chip-scale package
Brand Analog Devices Analog Devices Analog Devices
Synthesizer Architecture Fractional-N Fractional-N Fractional-N
Control Interface 3-wire serial interface 3-wire serial interface 3-wire serial interface
Lock Detection Digital Digital Digital
Power-Down Mode Supported Supported Supported
Pin Compatibility ADF4154 family pin-compatible reference ADF4154 datasheet identifies the ADF4153 as pin-compatible Pin-compatible family construction documented in comparison data
Output Type Clock Clock Clock

Principaux différenciateurs

  • Higher upper RF frequency than the ADF4153 family alternative (vs ADF4153BCPZ-RL7)
  • Documented family pin compatibility supports PCB reuse (vs ADF4153BCPZ-RL7)
  • Programmable dual-modulus prescaler supports flexible RF division (vs ADF4157BCPZ-RL7)
  • Separate VP connection supports extended tuning-voltage design (vs ADF4153BCPZ-RL7)

Notes de conception

Use the manufacturer package drawing to define the 20-WFQFN land pattern and exposed-pad connection. Keep the RF output route short and away from the digital write-data line and reference-clock path. Provide a continuous ground reference under the device, place bypass capacitors at the supply pins, and route the charge-pump and loop-filter connections away from high-current switching nodes to reduce coupling and phase-noise degradation.

Do not select a family alternative from package appearance alone. The ADF4153 has a lower upper-frequency capability, while the ADF4157 has a different upper-frequency specification; either substitution must be checked against the complete frequency plan. Also review register behavior, required output-buffer configuration, reference-input requirements, and loop-filter recalculation before treating either part as a production replacement.

Separate the AVDD supply-decoupling network from noisy digital and RF return currents. Use the manufacturer-recommended capacitor values and placement around the device, and keep the exposed pad thermally and electrically connected as directed. The VP connection is not a substitute for the main supply: its allowed voltage and decoupling depend on the selected charge-pump and tuning-voltage implementation, so verify those limits before energizing the circuit.

Design the reference input as a clean, controlled clock source because reference phase noise and spurs propagate through the fractional-N loop. Keep the reference trace short, provide a defined return path, and isolate it from the 3-wire programming signals. After assembly, evaluate reference spurs, fractional-N spur behavior, lock margin, and phase noise at the intended output frequency rather than relying only on the synthesizer's maximum-frequency rating.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established for the exact ordering code. AEC-Q100 status is not applicable because this is not presented as an automotive-qualified ordering code.

Données vérifiées le : 2026-11-15 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

ADF4154BCPZ-RL7 datasheet ADF4154BCPZ-RL7 pinout ADF4154BCPZ-RL7 datasheet pdf ADF4154BCPZ-RL7 equivalent ADF4154BCPZ-RL7 replacement ADF4154BCPZ-RL7 cross reference ADF4154BCPZ-RL7 footprint ADF4154BCPZ-RL7 price ADF4154BCPZ-RL7 stock Analog Devices ADF4154BCPZ-RL7 ADF4154BCPZ-RL7 vs ADF4153BCPZ-RL7 ADF4154BCPZ-RL7 vs ADF4157BCPZ-RL7 ADF4154BCPZ-RL7 RF synthesizer ADF4154BCPZ-RL7 application circuit

Composants & termes associés

Analog Devices ADF4154BCPZ-RL7 ADF4153BCPZ-RL7 ADF4157BCPZ-RL7 ADF4154 fractional-N frequency synthesizer frequency synthesizer phase-locked loop PLL local oscillator phase-frequency detector precision charge pump sigma-delta fractional interpolator dual-modulus prescaler 4/5 prescaler 8/9 prescaler digital lock detect 3-wire serial interface 20-WFQFN exposed-pad package QFN package family surface-mount package RF bandwidth 4 GHz 2.7 V to 3.3 V power supply separate VP tuning supply
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ