ADM3483ARZ - 3.3V 250kbps RS-485 Transceiver | Analog Devices
Référence : ADM3483ARZ ✓ ActifADM3483ARZ Présentation
An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables and noisy environments. The RS-485/RS-422 transceiver category belongs to the broader interface-IC hierarchy and enables multiple nodes to share a two-wire bus while improving noise immunity, grounding flexibility, and common-mode tolerance compared with single-ended signaling.
The ADM3483ARZ operates from a single 3.3 V supply and supports the standard low-power 3.3 V operating range of 3.0 V to 3.6 V. Key features include a maximum data rate of 250 kbps, reduced slew rates for low EMI, and support for as many as 32 transceivers on one bus. The device also tolerates bus voltages up to +12 V according to the product description.
The half-duplex architecture allows the same differential pair to carry transmitted or received data, but only one direction can be active at a time. Driver-enable and receiver-enable inputs provide local control of bus direction and receiver state. This arrangement reduces external interface logic when a connected microcontroller or host controller needs to switch between driving a command and listening for a response.
Typical applications include industrial automation controllers, building-automation equipment, remote sensor interfaces, instrumentation links, and low-power embedded communications modules. A 250 kbps rate is appropriate for moderate-speed control and monitoring rather than high-bandwidth factory protocols. The device is particularly useful where low EMI, a 3.3 V supply, and multipoint bus capability matter more than maximum line rate.
Design the bus with a symmetric differential trace geometry, controlled impedance, proper termination, and a common-mode strategy appropriate to the installation. Keep transceiver and connector ground references consistent, and account for cable delay when determining whether the selected data rate is safe for the total bus length.
This page combines manufacturer specifications, drop-in replacement information, interface-design guidance, and application-focused comparisons to support component selection and PCB implementation beyond the basic ordering information.
Alternatives de remplacement direct pour ADM3483ARZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
ADM3483EARZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
SP3483CN-L
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADM3483ARZ Spécifications
| Product Type | Half-duplex RS-485/RS-422 transceiver |
| Supply Voltage Range | 3.0 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 250 kbps |
| Driver and Receiver Count | 1 transmitter and 1 receiver |
| Duplex Mode | Half-duplex |
| Supported Standards | EIA RS-485 and TIA/EIA RS-422 |
| Output Slew Rate | Reduced, slew-rate limited |
| Maximum Bus Nodes | 32 transceivers per bus |
| Maximum Bus Voltage | +12 V |
| Shutdown Supply Current | 2 nA |
| Enable Controls | Separate DE and RE inputs |
| Plage de température de fonctionnement | -40°C to +85°C |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface mount |
Guide de configuration des broches du ADM3483ARZ 8-pin soic
Configuration des broches du ADM3483ARZ (boîtier 8-pin soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ADM3483ARZ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ADM3483ARZ convient pour 6 applications: Industrial Sensor Networks, Building Automation Controllers, Instrumentation Data Links, Remote Sensor Interfaces, Embedded Communication Modules, Process Control Interfaces.
Industrial Sensor Networks
The ADM3483ARZ fits industrial sensor networks that distribute measurements over a shared 3.3 V RS-485 bus. Its 250 kbps maximum rate supports moderate-speed environmental monitoring, pressure sensing, and equipment-status reporting, while the reduced-slew-rate outputs help control electromagnetic interference. The half-duplex architecture lets one eight-pin device provide both transmission and reception, and support for up to 32 bus nodes supports distributed installations. Engineers should match the data rate to total cable length and node count, then verify termination and common-mode behavior for the industrial environment.
Recommandé
Building Automation Controllers
The ADM3483ARZ is suitable for building-automation controller boards that communicate with distributed lighting, HVAC, access, and occupancy modules. Its single 3.0 V to 3.6 V supply operation simplifies connection to 3.3 V embedded controllers, while DE and RE inputs permit controlled bus-direction switching. The 250 kbps limit suits supervisory command and status traffic rather than high-bandwidth building data. Low-EMI slew-rate behavior also helps reduce coupling into adjacent control and sensor circuits, although cable routing and grounding remain critical in multi-floor installations.
Recommandé
Instrumentation Data Links
The ADM3483ARZ can connect laboratory or process-instrumentation equipment over a balanced RS-485 or RS-422 link. Its differential signaling improves noise immunity compared with single-ended interfaces, and the 3.3 V supply allows operation alongside modern control electronics. The 250 kbps data rate accommodates measurement commands, configuration data, and periodic readings without imposing the power and EMI burden of a much faster transceiver. For reliable commissioning, verify input and output logic levels, enable timing, protection networks, and termination against the final cable and instrument configuration.
Recommandé
Remote Sensor Interfaces
The ADM3483ARZ is appropriate for remote sensing modules connected through a 3.3 V RS-485 field bus. One half-duplex transceiver supports command transmission and sensor-response reception while limiting board area, and the 250 kbps rate is more than sufficient for periodic environmental and equipment readings. Its shutdown capability can also support systems that conserve power between activity periods. The installation must still account for bus-node count, cable attenuation, grounding, and surge exposure, particularly when sensors are connected by long outdoor cables.
Recommandé
Embedded Communication Modules
The ADM3483ARZ supports compact embedded communication modules that expose a 3.3 V serial host interface to an RS-485 field network. Half-duplex operation reduces the number of signal paths, while separate DE and RE control lets firmware manage transmission and reception states. The transceiver's 250 kbps rate suits configuration and telemetry traffic and its reduced slew rate limits high-frequency edge energy. Firmware should account for driver enable, receiver enable, turnaround delay, bus-idle behavior, and any requirement to detect a disconnected or reversed bus.
Recommandé
Process Control Interfaces
The ADM3483ARZ is useful in process-control interface cards that distribute commands and collect equipment status over a reliable balanced bus. Its RS-485 and RS-422 compatibility, 3.3 V supply, and 250 kbps rate align with supervisory control tasks such as actuator commands and diagnostic reporting. The 32-node capability permits multiple field devices to share a line, while the half-duplex topology reduces wiring. Designers should verify the bus remains within the device electrical limits at maximum cable length and should apply appropriate surge, ESD, grounding, and shielding measures at exposed connectors.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADM3483ARZ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADM3483EARZ | SP3483CN-L |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Exar |
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Product Type | Half-duplex RS-485/RS-422 transceiver | Half-duplex RS-485/RS-422 transceiver | Low-power RS-485 transceiver |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.3 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps |
| Duplex Mode | Half-duplex | Half-duplex | Half-duplex |
Principaux différenciateurs
- Closest same-family replacement adds enhanced ESD protection without changing the core interface function (vs ADM3483EARZ)
- Same 3.3 V low-power RS-485 positioning as the original (vs SP3483CN-L)
- Supports a substantial multipoint bus while retaining reduced EMI behavior (vs SP3483CN-L)
Notes de conception
Route the differential pair as a short, symmetric, continuously referenced trace with a solid ground plane beneath it. Place the transceiver close to the connector so transient current from the cable returns through the protection network rather than across sensitive controller traces. Avoid stubs, vias in the paired route where practical, and splits in the ground plane. Apply the protection components specified by the manufacturer datasheet at the connector boundary.
Do not assume that a shared RS-485 package automatically supports every full-duplex or shutdown-capable substitute. Verify DE and RE polarity, receiver enable behavior, driver disable characteristics, input thresholds, fail-safe response, maximum data rate, and shutdown current. The ADM3483EARZ is the closest same-family choice; SP3483CN-L requires an engineering review of its complete electrical table before production substitution.
Match the cable, transceiver, and termination strategy to the selected 250 kbps rate. Use a termination resistor only at the physical ends of the bus, account for the cable propagation delay when calculating the maximum practical rate, and provide a defined idle state for the driver. Slew-rate control reduces high-frequency energy but does not remove the need for proper grounding, shielding, or surge protection.
Informations de conformité
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the target MPN. AEC-Q100 qualification was not identified for this industrial interface IC.