ADS8341EB - 16-Bit 4-Channel 100 kHz ADC | Texas Instruments
Référence : ADS8341EB ✓ ActifADS8341EB Présentation
A sampling ADC is a semiconductor that samples an analog voltage at a controlled interval and converts each sample into a digital code. The ADS8341 belongs to the SAR ADC family, where a successive-approximation conversion architecture produces a digital result through a sequence of internal comparisons. Its serial interface integrates directly with microcontrollers, DSPs, and programmable logic while minimizing external data-bus wiring.
The four input channels can be arranged as four single-ended inputs or two differential inputs. This flexibility supports sensor interfaces, process-control instrumentation, and measurement systems in which common-mode noise rejection is important. The 100 kHz conversion rate provides sufficient throughput for many industrial, communications, and control applications, while 16-bit resolution preserves fine detail in slow or precision-oriented measurements.
According to the Texas Instruments product documentation, typical power dissipation is 8 mW with a 5 V supply at a 100 kHz throughput rate. The device uses a synchronous serial interface, allowing conversion data to be transferred in a predictable clocked sequence. Its 86 dB SINAD specification quantifies signal-to-noise plus distortion performance and is the key figure for assessing usable conversion accuracy in the intended analog bandwidth.
Typical applications include factory process monitoring, portable measurement equipment, industrial data acquisition, and embedded sensor conditioning. Differential operation is particularly useful when the source is centered around a common-mode voltage or when cable noise could otherwise influence the measurement. The low power consumption also suits compact systems in which converter throughput must be balanced against thermal and battery requirements.
Design the input network so that source impedance, settling time, and the acquisition interval meet the converter’s sampling requirements. Use a stable reference voltage, place input and reference decoupling capacitors close to their pins, and route the serial clock and data signals away from noisy switching nodes. Confirm timing for CS, SCLK, and data-valid signals against the interface timing in the manufacturer datasheet.
This page consolidates the key electrical limits, channel configurations, package information, interface considerations, and drop-in replacement guidance for the ADS8341EB. It also adds practical selection and PCB guidance so engineers can evaluate the converter alongside pin-compatible family options before committing to a design.
Alternatives de remplacement direct pour ADS8341EB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADS8341EB (même facteur de forme et même empreinte) — différant par Number of Input Channels, Package, Resolution, RoHS Status, SINAD.
ADS7841E/2K5G4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ADS8341EB Valeurs maximales et caractéristiques électriques
| Converter Type | Successive-approximation sampling ADC |
| Résolution | 16 bit |
| Number of Input Channels | 4 channels |
| Input Configuration | 4 single-ended or 2 differential inputs |
| Maximum Conversion Rate | 100 kHz |
| Output Interface | Synchronous serial interface |
| SINAD | 86 dB |
| Linearity Error | 0.0092% |
| Supply Voltage Range | 2.7 V to 5 V |
| Typical Power Dissipation | 8 mW at 5 V supply and 100 kHz throughput |
| Plage de température de fonctionnement | -40°C to +85°C |
| Boîtier | 16-pin SSOP |
| Type de montage | Surface mount |
| Analog Input Type | Single-ended or differential |
| Statut RoHS | unknown |
Guide de configuration des broches du ADS8341EB 16-pin ssop
Configuration des broches du ADS8341EB (boîtier 16-pin ssop). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour ADS8341EB.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ADS8341EB convient pour 6 applications: Industrial Sensor Acquisition, Process Control Monitoring, Portable Measurement Equipment, Instrumentation and Data Loggers, Communication Receive-Path Monitoring, Automated Test Equipment.
Industrial Sensor Acquisition
The ADS8341EB suits multi-sensor industrial acquisition because it combines four single-ended inputs with 16-bit conversion resolution and throughput up to 100 kHz. A controller can select a channel, acquire the analog value, and transfer the result through the synchronous serial interface without requiring four separate converters. The 86 dB SINAD and 0.0092% linearity error are important when the measured quantity is smaller than the full-scale signal. Use differential mode when two sensors or a sensor plus reference share the same conversion network. Front-end protection, guarding, and a stable reference are still required when sensors are exposed to industrial electrical noise or ground-potential differences.
Recommandé
Process Control Monitoring
The ADS8341EB fits closed-loop process monitoring where pressure, temperature, flow, or position signals must be digitized with repeatable performance. Its conversion rate of up to 100 kHz provides a substantial margin above slow industrial control loops, while four channels permit related variables to be measured with one converter. Differential input capability can reduce common-mode pickup when sensor wiring is longer or shares ground paths with actuators. The 16-bit code width and 86 dB SINAD support precise control decisions, although the complete loop must also account for sensor accuracy, reference stability, isolation, filtering, and control-loop timing.
Recommandé
Portable Measurement Equipment
The ADS8341EB is useful in handheld or compact measurement equipment because it provides four channels at 16-bit resolution while typically dissipating 8 mW at a 5 V supply and 100 kHz throughput. Its 2.7 V to 5 V operating range supports multiple embedded supply configurations. Low channel count per package also reduces board area compared with four separate converters. For battery-powered products, verify the actual conversion rate, digital interface activity, reference circuit, and analog front-end current because the typical 8 mW figure describes one defined operating condition. Low-power sleep modes, if used, should be confirmed in the datasheet before they are relied upon in an energy budget.
Recommandé
Instrumentation and Data Loggers
The ADS8341EB works well in instrumentation and data loggers that need accurate conversion of several slowly changing or moderate-speed analog signals. Four single-ended channels can capture thermocouple conditioning outputs, bridge signals, potentiometer positions, or auxiliary measurements without multiplying the converter count. Differential operation is appropriate when a bridge or differential sensor is centered around a common-mode voltage. The synchronous serial interface reduces pin count and supports deterministic communication with a microcontroller or DSP. For logged data, ensure that the selected sample interval satisfies both the 100 kHz conversion capability and the required acquisition time for the source impedance.
Recommandé
Communication Receive-Path Monitoring
The ADS8341EB can monitor received or transmitted signal levels in communication equipment when four independent analog measurement points must be digitized. Its 100 kHz conversion rate is suitable for supervisory envelope, supply, temperature, and calibration measurements rather than direct wideband waveform capture. The 16-bit resolution and 86 dB SINAD are useful when monitoring small changes around a large operating point. Use differential channels where available to suppress common-mode noise. The serial interface enables transfer to a baseband processor, but signal bandwidth, aliasing, input bandwidth, and filtering must be evaluated separately from the nominal conversion rate.
Recommandé
Automated Test Equipment
The ADS8341EB can serve as the measurement converter in automated test equipment that evaluates several analog nodes during board characterization. Four channels enable concurrent sampling or rapid channel sequencing, while 16-bit resolution supports calibration and fault-detection tasks with fine code widths. The 100 kHz throughput supports test systems that need frequent measurements rather than ultra-high-rate waveform analysis. Differential input mode improves measurement integrity for balanced fixtures and low-level signals. Test engineers should characterize offset, gain, linearity, and reference behavior over the intended temperature range, because converter resolution alone does not establish complete instrument accuracy.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADS8341EB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADS7841 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP |
| Input Configuration | 4 single-ended or 2 differential inputs | 2 single-ended inputs |
Principaux différenciateurs
- Broader analog input configuration than ADS7841 (vs ADS7841)
- Specified precision performance (vs ADS7841)
- Defined operating and thermal benchmark (vs ADS7841)
Notes de conception
Treat channel count as a functional as well as a pin-level decision. ADS8341EB supports four single-ended or two differential inputs, whereas ADS7841 is a two-channel single-ended device. A board that routes all four ADS8341 channels will not function equivalently with ADS7841 even though the family is described as pin-for-pin compatible. Create the schematic around the required input mode and verify unused-channel connections against the manufacturer pin-description table.
Place the reference bypass capacitor and analog input filtering components close to their associated SSOP pins. Route the synchronous serial clock, chip select, and data paths away from switching nodes and power inductors, and use a continuous ground reference beneath the device where the PCB stackup permits it. Differential inputs should use symmetrical routing and matched component placement to limit conversion of common-mode noise into differential error.
Verify source impedance and acquisition time before selecting the conversion interval. The ADC can operate at up to 100 kHz, but the external network driving each input must settle to the required accuracy within that interval. Keep the reference voltage stable, decouple it locally, and confirm the SCLK, CS, and data-valid timing in the manufacturer datasheet. These checks are especially important when the analog source has high impedance or a long acquisition interval.
Informations de conformité
The ADS8341 family documentation does not establish all requested compliance attributes. The EB ordering suffix should be checked against the current manufacturer ordering information when lead-free status is required.