AK5385AVS - 24-Bit Stereo Audio ADC | Asahi Kasei
Référence : AK5385AVS ✓ ActifAK5385AVS Présentation
An audio ADC converts left and right analog audio signals into digital data for processing, storage, transmission, or playback. The AK5385AVS belongs to the delta-sigma ADC family, a semiconductor category that uses noise shaping and digital filtering to provide high-resolution conversion. Within the broader signal-chain hierarchy, it sits between analog microphones, line-level inputs, or instrument preamplifiers and the digital audio processing stage of an AV receiver, mixer, recorder, or musical instrument.
The AK5385AVS provides 24-bit resolution, operation from 8 kHz through 216 kHz, and two simultaneous audio channels. Its fully differential input architecture supports noise reduction by rejecting common-mode interference on analog input lines. Enhanced Dual Bit technology is the defining modulator approach and is intended to balance conversion accuracy with implementation cost. A 114 dB dynamic range provides ample signal headroom for high-end audio applications.
The serial digital interface allows digitized audio to be transferred efficiently to a DSP, audio codec, processor, or digital recording system. Delta-sigma conversion makes the AK5385AVS particularly appropriate for audio-band signals where high resolution and linearity are more important than the very low conversion latency required by some communications and control applications. The 28-pin SOP provides a conventional surface-mount footprint suitable for established audio-equipment layouts.
Typical uses include professional audio preamplifiers, multichannel mixers, digital recording equipment, AV amplifiers, musical instruments, and high-end home-audio signal paths. In each case, the converter accepts analog audio and creates 24-bit digital samples at rates up to 216 kHz. Differential input wiring and careful analog grounding are important for preserving the full benefit of the converter's common-mode rejection and 114 dB dynamic range.
Designers should use the manufacturer pin-description table when assigning PCB nets and should treat the analog, digital, and power-supply sections as separate domains. Input and reference routing should be short and symmetric, with filtering placed where the datasheet specifies rather than adding arbitrary capacitance to signal or reference pins. Clock and digital-interface timing must also follow the manufacturer requirements for the selected operating mode.
This product page combines the AK5385AVS conversion specifications, package information, application guidance, and same-family replacement analysis into an engineering-focused overview. It also identifies the limited availability of verified drop-in alternatives rather than presenting cross-package parts as replacements.
Alternatives de remplacement direct pour AK5385AVS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec AK5385AVS (même facteur de forme et même empreinte) — différant par Converter Type, Package.
AK5385BVS
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →AK5385AVS Valeurs maximales et caractéristiques électriques
| Converter Type | 24-bit delta-sigma ADC |
| Number of Channels | 2 channels |
| Résolution | 24 bit |
| Maximum Sampling Frequency | 216 kHz |
| Nominal High-End Sampling Rate | 192 kHz |
| Minimum Sampling Frequency | 8 kHz |
| Dynamic Range | 114 dB |
| Architecture | Enhanced Dual Bit delta-sigma |
| Analog Input Configuration | Fully differential |
| Digital Interface | Serial |
| Boîtier | 28-pin SOP |
| Package Width | 7.50 mm |
| Type de montage | Surface mount |
| Plage de température de fonctionnement | -40 C to +85 C |
| Envelope and Package Details | Surface-mount 28-SOIC, 7.50 mm width |
Guide de configuration des broches du AK5385AVS surface-mount 28-soic, 7.50 mm width
Configuration des broches du AK5385AVS (boîtier surface-mount 28-soic, 7.50 mm width). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AK5385AVS.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AK5385AVS convient pour 6 applications: Professional Audio Preamplifier, Digital Audio Recorder, High-End AV Amplifier, Musical Instrument Capture, Digital Mixer, Home Audio Signal Processor.
Professional Audio Preamplifier
The AK5385AVS fits a professional audio preamplifier because it converts two balanced analog channels into 24-bit digital samples at rates from 8 kHz to 216 kHz. According to the manufacturer datasheet, its fully differential input architecture helps reject common-mode interference, while its 114 dB dynamic range preserves signal headroom. It can sit between balanced line inputs and a DSP that handles mixing, level control, routing, or digital recording. Board design should preserve input symmetry, keep return paths short, and maintain a clean separation between the analog converter section and the downstream digital circuitry.
Recommandé
Digital Audio Recorder
For a digital recording system, the AK5385AVS provides two-channel, 24-bit conversion across an 8 kHz-to-216 kHz sampling range. The manufacturer datasheet identifies 114 dB dynamic range and enhanced Dual Bit delta-sigma architecture as central characteristics for high-accuracy audio acquisition. The converter can feed recorded PCM streams into a DSP or storage controller. Designers should synchronize the converter clock to the recording engine, observe serial-interface timing, and isolate converter clock signals from sensitive analog input routing.
Recommandé
High-End AV Amplifier
The AK5385AVS is suitable for the input stage of a high-end AV amplifier because it supports two 24-bit channels and sampling rates up to 216 kHz. According to the manufacturer datasheet, the fully differential inputs and 114 dB dynamic range suit high-end audio signal chains where low-level information must survive conversion. The ADC may precede a digital volume, decoding, or routing stage before a conventional power amplifier. Maintain matched analog input impedance and follow the manufacturer reference layout to avoid introducing gain error or channel imbalance.
Recommandé
Musical Instrument Capture
The AK5385AVS can capture instrument audio with 24-bit resolution at sampling rates from 8 kHz to 216 kHz. According to the manufacturer datasheet, AK5385A devices are intended for musical instruments as well as AV amplifiers and recorders. The two-channel architecture supports stereo or paired pickup inputs when the source is balanced. Place the converter near the preamplifier to minimize analog trace exposure, and verify grounding and reference arrangements against the manufacturer circuit examples.
Recommandé
Digital Mixer
The AK5385AVS supports the multichannel analog front end of a digital mixer by converting two channels at a time to 24-bit digital data. Sampling rates from 8 kHz to 216 kHz provide flexibility for music, speech, and studio capture, while the 114 dB dynamic range helps preserve quiet program material. The converter can feed a dedicated audio DSP that performs gain control, mixing, routing, and effects. Differential input routing and careful clock distribution are essential when several converter pairs operate within one cabinet.
Recommandé
Home Audio Signal Processor
The AK5385AVS is appropriate for a high-resolution home-audio processor that accepts balanced analog sources and outputs digital audio internally. According to the manufacturer datasheet, the converter supports 24-bit data and rates up to 216 kHz, while its two-channel structure matches common stereo source arrangements. Its differential inputs can help reject ground-related interference in balanced installations. The system should preserve converter timing margins, use a quiet reference implementation, and route high-speed digital signals away from the analog input network.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AK5385AVS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | AK5385BVS |
|---|---|---|
| Package | 28-pin SOP | 28-pin SOP |
| Brand | Asahi Kasei Microdevices | Asahi Kasei Microdevices |
| Mounting Type | Surface mount | Surface mount |
Principaux différenciateurs
- High-resolution stereo conversion (vs AK5385BVS)
- Broad high-resolution sampling range (vs AK5385BVS)
- Fully differential high-end audio inputs (vs AK5385BVS)
Notes de conception
Route the two fully differential analog inputs as short, symmetric pairs and keep them away from the serial clock, digital data, and switching-supply nodes. Use a continuous ground plane for return current, but partition the analog and digital regions according to the manufacturer reference layout. Input impedance, filter values, and reference-routing details should be taken from the manufacturer datasheet rather than inferred from generic ADC layouts.
Treat the converter clock as a high-speed digital signal even though the audio sample rate is comparatively low. Route the clock over a continuous reference plane, avoid stub branches, and provide a clean return path beneath the trace. Maintain spacing from analog inputs and use the manufacturer-recommended interface topology to prevent timing degradation, data errors, or channel-to-channel crosstalk.
Do not treat the 28-pin package size as proof that another 28-pin converter is interchangeable. Verify every pin name, supply voltage, analog reference arrangement, clock mode, serial format, and power-up sequence against the datasheet for each exact ordering code. A physical footprint match alone is insufficient for a safe replacement in an audio design.
Design the analog and digital supply paths so switching ripple and ground bounce do not modulate the converter input or reference voltage. Follow the manufacturer capacitor recommendations, maintain short supply connections, and separate noisy return currents from the analog input region. Confirm startup, shutdown, and rail-sequencing requirements against the specific device documentation.
Informations de conformité
No explicit environmental or material-compliance declarations were identified for the exact AK5385AVS ordering code. AEC-Q100 qualification is not indicated and is treated as not applicable to this audio converter.