ATMEGA162V-8AU - 8-bit AVR MCU 16KB Flash 8MHz TQFP-44 | Microchip
Référence : ATMEGA162V-8AU ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.85 | $6,85 |
| 10 | $6.18 | $61,80 |
| 100 | $5.49 | $549,00 |
| 500 | $4.92 | $2 460,00 |
| 1 000 | $4.38 | $4 380,00 |
ATMEGA162V-8AU Présentation
Key features include 8 MHz maximum CPU clock speed, 35 programmable I/O lines, dual UART interfaces, SPI, TWI (I2C-compatible), and 16 MIPS throughput at 16 MHz. The "V" suffix designates the 1.8V-5.5V wide operating voltage range optimized for battery-powered applications, while the "-8" speed grade limits maximum clock to 8 MHz at the lower end of the voltage range. The ATmega162V is the low-voltage variant of the ATmega162 family, sharing identical peripherals and pinout with the standard ATmega162 (which operates 2.7V-5.5V up to 16 MHz).
The AVR enhanced RISC architecture executes most instructions in a single clock cycle, achieving throughputs approaching 1 MIPS per MHz. This allows the system designer to optimize power consumption versus processing speed. Five sleep modes (Idle, Power-save, Power-down, Standby, Extended Standby) plus on-chip peripherals make the device suitable for energy-aware designs. The JTAG interface complies with IEEE 1149.1 standard, supporting boundary-scan and on-chip debug via debugWIRE or JTAG.
Typical applications include industrial control systems, battery-powered sensor nodes, building automation, motor control peripherals, USB-to-UART bridges, and embedded communication gateways that need two serial ports. The dual UART is a distinctive feature that simplifies designs requiring simultaneous host and peripheral serial connectivity. Industrial temperature rating (-40C to +85C) and 1.8V minimum Vcc enable 2x AA battery operation with extended runtime.
When designing with this device, note that the "V" variant's lower Vcc_min requires the -8 speed grade; using the standard ATmega162-16AU instead allows higher clock frequencies but raises Vcc_min to 2.7V. Decoupling requires 100nF on each Vcc pin placed within 5mm, plus a 10uF bulk capacitor on the main rail. The 44-TQFP (10x10) footprint is identical to ATmega162-16AU and ATmega162V-8PU, enabling PCB reuse across the family.
This page synthesizes distributor pricing, drop-in alternatives across the ATmega162 family, and practical design notes not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ATMEGA162V-8AU — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATMEGA162V-8AU (même facteur de forme et même empreinte) — différant par Throughput, Instruction Set, Core Architecture, Package, Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATMEGA162-16AU
✅ Remplacement direct✓ En stock
$2.45 / unité
Voir la fiche technique →ATMEGA162V-8AUR
✅ Remplacement direct✓ En stock
$6.62 / unité
Voir la fiche technique →ATMEGA162V-8AU Valeurs maximales et caractéristiques électriques
| Core Architecture | AVR 8-bit RISC |
| CPU Clock Speed (max) | 8 MHz |
| Throughput | 8 MIPS at 8 MHz |
| Program Memory (Flash) | 16 KB (8K x 16) |
| SRAM | 1 KB |
| EEPROM | 512 B |
| Operating Voltage Range | 1.8 V to 5.5 V (V variant) |
| Programmable I/O Lines | 35 |
| UART Interfaces | 2 |
| SPI | Yes |
| TWI (I2C-compatible) | Yes |
| JTAG / debugWIRE | Yes (IEEE 1149.1) |
| Boîtier | 44-TQFP (10x10 mm) |
| Température de fonctionnement | -40C to +85C (industrial) |
| Sleep Modes | 5 (Idle, Power-save, Power-down, Standby, Extended Standby) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
Configuration des broches de ATMEGA162V-8AU
| Broche 1 | VCC — Digital supply voltage (1.8-5.5V) |
| Broche 2 | XTAL2 — Crystal oscillator output |
| Broche 3 | XTAL1 — Crystal oscillator input |
| Broche 4 | RESET — Reset input (active low) |
| Broche 5 | PD0 — Port D bit 0 / RXD1 (UART1 receive) |
| Broche 6 | PD1 — Port D bit 1 / TXD1 (UART1 transmit) |
| Broche 7 | PD2 — Port D bit 2 / INT0 |
| Broche 8 | PD3 — Port D bit 3 / INT1 |
| Broche 9 | PD4 — Port D bit 4 |
| Broche 10 | PD5 — Port D bit 5 |
| Broche 11 | PD6 — Port D bit 6 |
| Broche 12 | PD7 — Port D bit 7 |
| Broche 13 | GND — Ground |
| Broche 14 | AVCC — Analog supply voltage |
| Broche 15 | AREF — ADC reference voltage |
| Broche 16 | PA0 — Port A bit 0 / ADC0 |
| Broche 17 | PA1 — Port A bit 1 / ADC1 |
| Broche 18 | PA2 — Port A bit 2 / ADC2 |
| Broche 19 | PA3 — Port A bit 3 / ADC3 |
| Broche 20 | PA4 — Port A bit 4 / ADC4 |
| Broche 21 | PA5 — Port A bit 5 / ADC5 |
| Broche 22 | PA6 — Port A bit 6 / ADC6 |
| Broche 23 | PA7 — Port A bit 7 / ADC7 |
| Broche 24 | AGND — Analog ground |
| Broche 25 | PC0 — Port C bit 0 / SCL |
| Broche 26 | PC1 — Port C bit 1 / SDA |
| Broche 27 | PC2 — Port C bit 2 |
| Broche 28 | PC3 — Port C bit 3 |
| Broche 29 | PC4 — Port C bit 4 |
| Broche 30 | PC5 — Port C bit 5 |
| Broche 31 | PC6 — Port C bit 6 |
| Broche 32 | PC7 — Port C bit 7 |
| Broche 33 | PB0 — Port B bit 0 / T0 |
| Broche 34 | PB1 — Port B bit 1 / T1 |
| Broche 35 | PB2 — Port B bit 2 / AIN0 |
| Broche 36 | PB3 — Port B bit 3 / AIN1 |
| Broche 37 | PB4 — Port B bit 4 / SS |
| Broche 38 | PB5 — Port B bit 5 / MOSI |
| Broche 39 | PB6 — Port B bit 6 / MISO |
| Broche 40 | PB7 — Port B bit 7 / SCK |
| Broche 41 | PE0 — Port E bit 0 / RXD0 |
| Broche 42 | PE1 — Port E bit 1 / TXD0 |
| Broche 43 | PE2 — Port E bit 2 / OC1B |
| Broche 44 | VCC — Digital supply voltage (1.8-5.5V) |
Applications typiques
ATMEGA162V-8AU convient pour 6 applications: Industrial Control Systems, Battery-Powered Sensor Nodes, USB-to-UART Bridge Devices, Building Automation Gateways, Motor Control Peripherals, Embedded Communication Modules.
Industrial Control Systems
The ATMEGA162V-8AU fits industrial control with its 8 MIPS throughput, dual UART, and 1.8-5.5V operation. The 35 programmable I/O lines handle sensors, actuators, and HMI peripherals without external expanders. Industrial temperature rating (-40C to +85C) and JTAG debug support simplify field diagnostics. Power-down mode with BOD enables unattended monitoring stations.
Recommandé
Battery-Powered Sensor Nodes
The ATMEGA162V-8AU's 1.8V Vcc_min enables direct 2x AA battery operation without boost converters. Five sleep modes reduce quiescent current to a few microamps, supporting multi-year battery life for wireless sensor nodes. The 1 KB SRAM and 16 KB Flash accommodate ZigBee/BLE protocol stacks or LoRaWAN drivers. The 8 MHz throughput handles periodic sensing and reporting.
Recommandé
USB-to-UART Bridge Devices
The ATMEGA162V-8AU's dual UART is ideal for USB-to-UART bridges that also need a secondary debug port. At 8 MHz the device can bit-bang USB low-speed or drive CDC ACM class devices via software stacks. Industrial temperature rating and 5V tolerance suit industrial USB hosts. JTAG allows firmware updates over USB without external programmers.
Recommandé
Building Automation Gateways
The ATMEGA162V-8AU's dual UART handles Modbus RTU and BACnet MS/TP simultaneously, common building automation protocols. SPI connects to Ethernet controllers or Wi-Fi modules for cloud connectivity. The 16 KB Flash stores protocol stacks, and JTAG supports field firmware upgrades via boundary-scan. Wide Vcc tolerance handles long 24V industrial wiring drops.
Recommandé
Motor Control Peripherals
The ATMEGA162V-8AU generates PWM and timing signals for stepper and BLDC motor control peripherals with its 16-bit timers. At 8 MIPS the device computes commutation tables for small brushless motors in real time. The 35 I/O lines drive gate drivers and read Hall sensors. Dual UART connects to host controllers for command/status reporting in distributed motor networks.
Recommandé
Embedded Communication Modules
The ATMEGA162V-8AU's SPI + UART + TWI peripherals form a flexible gateway between wireless modules and host processors. Its 8 MIPS throughput runs GSM/LoRa/BLE module command interpreters while JTAG enables in-circuit programming during OEM integration. Industrial temperature rating suits outdoor enclosures. 1.8V operation supports solar-powered remote terminals.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATMEGA162V-8AU — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATMEGA162-16AU | ATMEGA162V-8AUR | ATMEGA162V-8MU |
|---|---|---|---|---|
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-MLF (10x10 mm) - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Max CPU Clock | 8 MHz | 16 MHz | 8 MHz | 8 MHz |
| Operating Voltage (Vcc) | 1.8 V to 5.5 V | 2.7 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Flash Program Memory | 16 KB | 16 KB | 16 KB | 16 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB |
| EEPROM | 512 B | 512 B | 512 B | 512 B |
| UART Interfaces | 2 | 2 | 2 | 2 |
| I/O Lines | 35 | 35 | 35 | 35 |
| Temperature Range | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
Principaux différenciateurs
- Lowest Vcc_min in ATmega162 family at 1.8V (vs ATMEGA162-16AU)
- True drop-in with extended temperature data (vs ATMEGA162V-8AUR)
- TQFP-44 form factor for hand-soldering (vs ATMEGA162V-8MU)
Notes de conception
Decoupling: Place a 100nF ceramic capacitor on each VCC/AVCC pin within 5mm of the IC. Add a single 10uF tantalum or ceramic bulk capacitor on the main VCC rail. The 1.8V Vcc_min of the V variant requires a regulated LDO output for 2x AA battery systems - the TPS7A02 or similar 200mA LDO provides clean supply. Brown-out detection (BOD) should be enabled in fuses to prevent code corruption at low Vcc.
TQFP-44 thermal management: The TQFP-44 package has theta_JA around 50-60 C/W depending on PCB copper area. At 8 MHz with all peripherals enabled, typical active current is 5-10 mA at 3.3V, dissipating only 30 mW - thermal concerns are negligible for this device. The MLF-44 variant has a thermal pad that must be soldered to a ground copper pour (minimum 1 sq inch) for optimal thermal performance and electrical grounding.
PCB layout for JTAG: Place the 6-pin JTAG header (TCK, TMS, TDO, TDI, VCC, GND) within 50mm of the MCU for reliable debugWIRE/JTAG connection. Use series 100 ohm termination resistors on JTAG signals if traces exceed 25mm. Route XTAL1/XTAL2 traces short (under 10mm) and guard with ground plane to minimize EMI. Keep crystal traces away from switching power or high-current signals.
Common pitfalls: (1) Do not confuse ATmega162 with ATmega162V - the non-V variant cannot operate below 2.7V. (2) The -8 speed grade of the V variant is required for 1.8V operation; do not attempt higher speeds. (3) The dual UART requires proper register configuration for baud-rate generator independent setup. (4) JTAG and debugWIRE cannot be used simultaneously - select one in fuses. (5) ISP programming requires the RESET pin to be pulled high externally.
Informations de conformité
RoHS compliant per Microchip product page. Industrial temperature grade (-40C to +85C), not AEC-Q100 automotive qualified. Halogen-free status not explicitly stated in available data.