ATMEGA48-20MJ - 8-bit AVR MCU 20MHz 4KB Flash VQFN-32 | Microchip
Référence : ATMEGA48-20MJ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1 000 | $0 | $0,00 |
ATMEGA48-20MJ Présentation
A microcontroller unit (MCU) integrates a processor core, program memory, data memory, and peripherals on a single chip, sitting at the lowest level of the embedded systems hierarchy between discrete logic and application processors. The AVR architecture is a classic Harvard-architecture 8-bit family, executing most of its 131 instructions in a single clock cycle for high code efficiency.
Key features include the advanced RISC AVR core with 32 general-purpose working registers, in-system programmable Flash with optional boot-code section, and a rich peripheral set: two 8-bit timers, one 16-bit timer, six PWM channels, an 8-channel 10-bit ADC, a programmable serial USART, an SPI interface, and a two-wire (I2C-compatible) serial interface. The device operates from 1.8V to 5.5V, enabling both battery-powered and 5V industrial designs.
Technical depth: debugWIRE provides single-wire on-chip debugging over the RESET line, eliminating the need for a JTAG pod, while the self-programming Flash allows field firmware updates. Power management includes idle, ADC noise reduction, power-save, power-down, and standby sleep modes, with low quiescent consumption for battery applications.
Typical applications include industrial control and automation nodes, consumer appliances, sensor interfaces exploiting the 10-bit ADC, and low-cost battery-powered devices. The green/RoHS VQFN-32 (5x5 mm) package suits compact, thermally efficient surface-mount designs.
Design consideration: the suffix J denotes the MLF package and industrial temperature; verify VQFN footprint paste-stencil design, as the center die pad must be soldered to ground for reliable operation.
This page synthesizes distributor pricing, pin-compatible drop-in alternatives including the ATmega48A/48PA/88/328P MLF variants, and practical design notes not found in the manufacturer datasheet.
Alternatives de remplacement direct pour ATMEGA48-20MJ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATMEGA48-20MJ (même facteur de forme et même empreinte) — différant par Package, EEPROM, SRAM, ADC, Communication Interfaces.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATMEGA48-20MI
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →ATMEGA48-20MU
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATMEGA48A-MU
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ATMEGA48PA-MU
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1.08 / unité
Voir la fiche technique →ATMEGA88-20MU
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →ATMEGA168-20MU
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →ATMEGA328P-MU
✅ Remplacement direct✓ En stock
$2.85 / unité
Voir la fiche technique →ATMEGA48-20MJ Valeurs maximales et caractéristiques électriques
| Core Architecture | 8-bit AVR RISC |
| Fréquence d'horloge maximale | 20 MHz |
| Peak Throughput | 20 MIPS at 20 MHz |
| Flash Program Memory | 4 KB (2K x 16) |
| SRAM | 512 bytes |
| EEPROM | 256 bytes |
| Instructions | 131 instructions, most single-cycle |
| ADC Resolution | 10-bit |
| ADC Channels | 8-channel |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Température de fonctionnement | -40C to +85C (industrial) |
| Boîtier | 32-VQFN / MLF (5x5 mm), pad designation J |
| Timers | 2 x 8-bit, 1 x 16-bit |
| PWM Channels | 6 |
| Communication Interfaces | USART, SPI, 2-wire serial (I2C-compatible) |
| On-Chip Debug | debugWIRE |
| Sleep Modes | Idle, ADC Noise Reduction, Power-save, Power-down, Standby |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (green package) |
Configuration des broches de ATMEGA48-20MJ
| Broche 1 | PD3 (INT1) — Port D bit 3 / External interrupt 1 |
| Broche 2 | PD4 (XCK/T0) — Port D bit 4 / USART external clock / Timer0 clock input |
| Broche 3 | GND — Ground |
| Broche 4 | VCC — Digital supply voltage |
| Broche 5 | GND — Ground |
| Broche 6 | VCC — Digital supply voltage |
| Broche 7 | PB6 (XTAL1/TOSC1) — Port B bit 6 / Crystal oscillator input or timer oscillator |
| Broche 8 | PB7 (XTAL2/TOSC2) — Port B bit 7 / Crystal oscillator output or timer oscillator |
| Broche 9 | PD5 (T1) — Port D bit 5 / Timer1 external counter input |
| Broche 10 | PD6 (AIN0) — Port D bit 6 / Analog comparator positive input |
| Broche 11 | PD7 (AIN1) — Port D bit 7 / Analog comparator negative input |
| Broche 12 | PB0 (ICP1/CLKO) — Port B bit 0 / Timer1 input capture / Clock output |
| Broche 13 | PB1 (OC1A) — Port B bit 1 / Timer1 PWM output A |
| Broche 14 | PB2 (SS/OC1B) — Port B bit 2 / SPI slave select / Timer1 PWM output B |
| Broche 15 | PB3 (MOSI/OC2A) — Port B bit 3 / SPI master output / Timer2 PWM output A |
| Broche 16 | PB4 (MISO) — Port B bit 4 / SPI master input |
| Broche 17 | PB5 (SCK) — Port B bit 5 / SPI clock |
| Broche 18 | AVCC — ADC supply voltage |
| Broche 19 | ADC6 — ADC input channel 6 |
| Broche 20 | AREF — Analog reference voltage |
| Broche 21 | GND — Ground |
| Broche 22 | ADC7 — ADC input channel 7 |
| Broche 23 | PC0 (ADC8) — Port C bit 0 / ADC channel 8 |
| Broche 24 | PC1 (ADC9) — Port C bit 1 / ADC channel 9 |
| Broche 25 | PC2 (ADC10) — Port C bit 2 / ADC channel 10 |
| Broche 26 | PC3 (ADC11) — Port C bit 3 / ADC channel 11 |
| Broche 27 | PC4 (ADC12/SDA) — Port C bit 4 / ADC channel 12 / 2-wire data |
| Broche 28 | PC5 (ADC13/SCL) — Port C bit 5 / ADC channel 13 / 2-wire clock |
| Broche 29 | PC6 (RESET) — Port C bit 6 / Reset input (active low) |
| Broche 30 | PD0 (RXD) — Port D bit 0 / USART receive |
| Broche 31 | PD1 (TXD) — Port D bit 1 / USART transmit |
| Broche 32 | PD2 (INT0) — Port D bit 2 / External interrupt 0 |
Applications typiques
ATMEGA48-20MJ convient pour 6 applications: Industrial Control and Automation Nodes, Analog Sensor Interfaces, Battery-Powered Portable Devices, Serial Communication Bridges and Converters, Consumer Appliance Control Boards, Automotive-Adjacent and Rugged Embedded Subsystems.
Industrial Control and Automation Nodes
The ATMEGA48-20MJ fits industrial control nodes such as relay drivers, valve controllers, and PLC sub-modules because it combines a 20 MHz / 20 MIPS AVR core with 5V-tolerant I/O and a full industrial -40C to +85C rating. The 1.8V to 5.5V supply range allows direct operation from 5V industrial rails, while six PWM channels drive actuators and motor drivers without external timer ICs. In a typical node, the MCU reads sensors through the 8-channel 10-bit ADC, communicates to a supervisory controller via the USART or SPI bus, and switches loads through optocoupled drivers. The MLF-32 (5x5 mm) package keeps the PCB footprint compact on dense DIN-rail carrier boards, and the exposed die pad soldered to ground improves thermal margin and EMI behavior compared with TQFP. debugWIRE enables in-circuit firmware updates during commissioning without removing the device from the assembled board.
Recommandé
Analog Sensor Interfaces
With an 8-channel 10-bit ADC, internal bandgap reference, and ADC noise-reduction sleep mode, the ATMEGA48-20MJ is well suited to multi-sensor front ends such as temperature, pressure, and potentiometer inputs. All eight ADC channels (including the dedicated ADC6/ADC7 pads 19 and 22) are accessible in the MLF-32 pinout, letting one MCU multiplex several ratiometric sensors without an external analog mux. The ADC noise-reduction mode halts the CPU and I/O during conversion, cutting digital noise and improving effective resolution, a technique the manufacturer datasheet documents for precision measurements. Supplying AVCC from a clean 5V rail with a 100 nF decoupling capacitor on pad 18 and AREF filtered on pad 20 achieves stable reference behavior. Readings can be transmitted over USART to a host or logged via the 256-byte EEPROM, and threshold outputs can be driven from the six PWM channels for closed-loop control.
Recommandé
Battery-Powered Portable Devices
The ATMEGA48-20MJ supports battery designs through five sleep modes: idle, ADC noise reduction, power-save, power-down, and standby. In power-down the core halts while retaining register contents and waking on external interrupts, watchdog, or pin-change events, which suits periodic-sampling products such as metering pods, remote controls, and portable instrumentation. Operation down to 1.8V (with the 4 MHz low-voltage speed grade) allows running directly from two alkaline cells or a single LiFePO4 cell without a boost converter in low-speed applications. The 512-byte SRAM and 256-byte EEPROM hold configuration and calibration data across power cycles. Because quiescent draw is dominated by sleep-mode current rather than active operation at 20 MHz, firmware should favor the lowest clock that meets timing, and unused peripherals should be power-clocked off via the Power Reduction registers on newer revisions. debugWIRE assists low-power firmware tuning in-system.
Recommandé
Serial Communication Bridges and Converters
The combination of a hardware USART, SPI, and a two-wire (I2C-compatible) interface makes the ATMEGA48-20MJ effective as a protocol bridge, for example converting I2C sensor data to UART for a host, or SPI-to-UART translation in legacy equipment retrofits. The 20 MHz clock supports 1 Mbps-class USART rates needed for industrial links, and the AVR's single-cycle I/O access makes bit-banged extra protocols practical in the remaining firmware space. The self-programming Flash with optional boot section allows firmware-in-field updates over the serial link, reducing maintenance cost in installed equipment. At 5V, UART levels interface directly with RS-232 transceivers or RS-485 transceivers through external line drivers. Keep crystal-based clocking (XTAL1/XTAL2 pads 7-8) for baud-rate accuracy at the extremes of the industrial temperature range, since internal RC oscillator tolerance can violate UART timing budgets over temperature.
Recommandé
Consumer Appliance Control Boards
Cost-sensitive appliance controllers - fan speed controls, small pump timers, dishwasher and cooker panel logic - are a classic ATmega48 use case. The 4KB Flash is adequate for keypad scanning, LED multiplexing, relay sequencing, and simple state machines, and the 6 PWM channels directly drive triac/SCR optocoupler stages or brushed-motor drivers. The MLF-32 (5x5 mm) J-suffix package withstands the -40C to +85C environment found in appliance enclosures, and the exposed pad provides robust mechanical and thermal mounting on single-sided cost-optimized PCBs. The 1.8V to 5.5V range tolerates unregulated supply droop during motor start events when Brown-out Detection fuses are configured appropriately. Production programming via the SPI ISP header allows flash-after-assembly, and the EEPROM stores calibration and cycle-count data. For new appliance designs requiring more code space, the pin-compatible ATMEGA328P-MU provides a direct migration path without PCB respin.
Recommandé
Automotive-Adjacent and Rugged Embedded Subsystems
While the standard ATMEGA48-20MJ is not AEC-Q100 qualified, its -40C to +85C industrial rating, wide 1.8V to 5.5V supply tolerance, and robust AVR core make it appropriate for rugged non-safety automotive-adjacent subsystems such as accessory lighting controllers, agricultural implement sensors, and marine instrumentation where full automotive qualification is not contractually required. Brown-out Detection and the watchdog timer provide fault recovery in noisy 12V environments, typically powered through a 5V regulator downstream of load-dump-protected front-end circuitry. The MLF-32 package's exposed die pad improves vibration reliability of the solder joint compared with leaded packages when properly stenciled. Designers needing formal automotive qualification within the same footprint should evaluate qualified AVR family members instead. debugWIRE and ISP support field diagnostics, and the ADC accommodates resistive and Hall-effect sensor inputs directly.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATMEGA48-20MJ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATMEGA48-20MI | ATMEGA48A-MU | ATMEGA48PA-MU | ATMEGA328P-MU |
|---|---|---|---|---|---|
| Package | VQFN/MLF-32 (5x5 mm) | VQFN/MLF-32 (5x5 mm) - same | VQFN/MLF-32 (5x5 mm) - same | VQFN/MLF-32 (5x5 mm) - same | VQFN/MLF-32 (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 4 KB | 4 KB | 4 KB | 4 KB | 32 KB |
| SRAM | 512 bytes | 512 bytes | 512 bytes | 512 bytes | 2 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 1 KB |
| Max Clock / Throughput | 20 MHz / 20 MIPS | 20 MHz / 20 MIPS | 20 MHz / 20 MIPS | 20 MHz / 20 MIPS | 20 MHz / 20 MIPS |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| Firmware Compatibility | Baseline (ATmega48 register map) | Identical - direct swap | Code-compatible, verify fuses | Code-compatible, verify fuses | Requires porting (register/fuse differences) |
Principaux différenciateurs
- Baseline lowest-cost 4KB AVR with full industrial rating (vs ATMEGA328P-MU)
- debugWIRE single-wire on-chip debugging (vs ATMEGA48-20AU (TQFP version))
- Newer revision migration without respin (vs ATMEGA48PA-MU)
Notes de conception
The MLF-32 (5x5 mm) package requires soldering the central die pad to the PCB ground plane for mechanical reliability, thermal dissipation, and EMI performance. Design an array of thermal vias (approximately 4x4, 0.3 mm drill) under the exposed pad and connect them to the ground pour. Do not flood the pad with excessive paste; use a segmented stencil pattern (about 50-60% coverage) to prevent solder voiding and package float, which can lift outer pad joints during reflow.
Decouple VCC (pads 4, 6) with 100 nF ceramic capacitors placed within 2 mm of the pads, plus 4.7-10 uF bulk capacitance per board. Decouple AVCC (pad 18) separately with 100 nF and connect to VCC through a small LC filter or ferrite bead when ADC accuracy matters; tie AREF (pad 20) to GND via 100 nF when using the internal reference. Configure the Brown-out Detection fuse to match the supply rail - at 5V systems use BOD 4.3V; disable BOD below 2.7V systems to avoid spurious resets at startup.
PC6/RESET (pad 29) must be held high during normal operation; leaving it floating causes random resets, and enabling debugWIRE clears the RESET-disable fuse such that SPI ISP programming is blocked until debugWIRE is disabled. When migrating firmware to ATmega88/168/328P pin-compatible parts, remember fuse map and register address differences - a fuse file saved for ATmega48 will not program an ATmega328P correctly. Also verify the speed/voltage curve: 20 MHz operation is only rated at 4.5V-5.5V.
For UART operation near the top baud rates, prefer an external crystal on XTAL1/XTAL2 (pads 7-8) over the internal RC oscillator; RC tolerance drifts over the -40C to +85C range can exceed UART frame timing budgets. Route the crystal with short traces, ground guard ring, and keep SPI/USART lines away from the ADC input traces (pads 19, 22, 23-28). If switching loads share the board, star-ground the analog section to the die pad to prevent ground-bounce errors on 10-bit ADC readings.
Informations de conformité
Distributor listings classify the ATMEGA48-20MJ as RoHS-compliant green-package silicon. This standard part is not AEC-Q100 qualified. REACH, halogen-free, and conflict-minerals status were not stated in the verified sources - request Microchip material declarations for certification data.
