ATSAMA5D23B-CN - 500MHz ARM Cortex-A5 MPU 128KB SRAM | Microchip
Référence : ATSAMA5D23B-CN ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.85 | $14,85 |
| 10 | $13.42 | $134,20 |
| 100 | $11.97 | $1 197,00 |
| 500 | $10.68 | $5 340,00 |
| 1 000 | $9.55 | $9 550,00 |
ATSAMA5D23B-CN Présentation
A microprocessor (MPU) is an integrated circuit that contains the full CPU, cache, memory controller and peripheral interfaces on a single die, in contrast to a microcontroller (MCU) which typically integrates on-chip Flash and modest RAM. The ATSAMA5D23B-CN belongs to the SAMA5D2 family of low-power, high-integration MPUs from Microchip that target industrial HMI, IoT gateways, and connected embedded products. The series uses a low-power architecture that achieves 5 uA in backup mode, supporting extensive battery life for always-on edge nodes.
Key features include 32 kbyte L1 instruction cache, 32 kbyte L1 data cache, a memory management unit (MMU), ARM TrustZone hardware isolation, and an integrated peripheral touch controller. The device supports LPDDR/DDR2/DDR3 external memory interfaces through its EBI, plus 12-bit ADC, CAN, USB HS, EMAC, image sensor interface, and I2S audio subsystem. The 0.8 mm ball pitch reduces PCB design complexity versus finer-pitch BGA variants.
The Cortex-A5 core uses the Armv7-A instruction set with Neon SIMD for media acceleration, executed through a dual-issue pipeline that delivers 1.57 DMIPS/MHz. TrustZone extensions provide hardware isolation between secure and non-secure execution, enabling secure boot and DRM for media applications. The integrated audio subsystem and LCD controller allow direct connection of TFT displays without an external companion chip.
Typical applications include industrial human-machine interfaces (HMI), IoT edge gateways, smart energy meters, building automation panels, and barcode scanners. The combination of low power consumption, integrated graphics and peripheral touch controller makes it well suited for battery-powered graphical products.
When designing with this device, ensure the PCB supports 0.8 mm microvia stack-up for the TFBGA-196 footprint. Power supply sequencing must follow the SAMA5D2 reference schematic to avoid back-powering through I/O rails during cold boot.
Alternatives de remplacement direct pour ATSAMA5D23B-CN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATSAMA5D23B-CN (même facteur de forme et même empreinte) — différant par Package, Ethernet, USB, Mounting Type, CAN.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATSAMA5D23A-CN
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$9.15 / unité
Voir la fiche technique →ATSAMA5D23B-CNR
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$10.25 / unité
Voir la fiche technique →ATSAMA5D22B-CUR
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$9.1 / unité
Voir la fiche technique →ATSAMA5D21B-CU
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$9.8 / unité
Voir la fiche technique →ATSAMA5D225C-D1M-CU
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$12.6 / unité
Voir la fiche technique →ATSAMA5D23A-CUR
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$8.95 / unité
Voir la fiche technique →ATSAMA5D23B-CN Valeurs maximales et caractéristiques électriques
| Core Architecture | ARM Cortex-A5 (Armv7-A) |
| Number of Cores | 1 |
| Maximum Clock Speed | 500 MHz |
| L1 Instruction Cache | 32 kbyte |
| L1 Data Cache | 32 kbyte |
| L2 Cache | 128 kbyte (configurable as internal SRAM) |
| NEON Media Engine | Yes |
| ARM TrustZone | Yes |
| MMU | Yes |
| Boîtier | 196-TFBGA (11x11 mm) |
| Ball Pitch | 0.8 mm |
| Type de montage | Surface Mount |
| Backup Mode Current | 5 uA typical |
| Largeur du bus de données | 32-bit |
| Series | SAMA5D2 |
| Statut RoHS | Compliant |
Guide de configuration des broches du ATSAMA5D23B-CN 196-tfbga (11x11 mm)
Configuration des broches du ATSAMA5D23B-CN (boîtier 196-tfbga (11x11 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour ATSAMA5D23B-CN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ATSAMA5D23B-CN convient pour 7 applications: Industrial Human-Machine Interface (HMI) Panels, IoT Edge Gateways, Smart Energy Meters, Building Automation Controllers, Connected Barcode Scanners and POS Terminals, Battery-Powered Wearable Medical Devices, Industrial Printer and Label Maker Controllers.
Industrial Human-Machine Interface (HMI) Panels
The ATSAMA5D23B-CN drives industrial HMI panels where the integrated 500 MHz Cortex-A5 core plus on-chip LCD controller deliver smooth Qt/Embedded GUI rendering at WVGA resolutions without an external graphics chip. Its 128 kbyte L2 cache and 32 kbyte L1 caches reduce DDR3 transactions, allowing the panel to refresh at 60 Hz while sustaining touchscreen response. The peripheral touch controller (PTC) interfaces directly to projected-capacitive touch sensors, eliminating an external touch IC. Compared with a discrete MPU + touch controller solution, the D23 reduces BOM count by 2-3 ICs, simplifies the PCB stack-up, and lowers total system cost for factory-floor operator panels and building-automation touchscreens.
Recommandé
IoT Edge Gateways
Edge gateways aggregate sensor data from multiple field busses and need both deterministic networking and headroom for on-device analytics. The ATSAMA5D23B-CN integrates dual CAN-FD controllers, 10/100 EMAC, USB HS, and multiple UART/SPI/I2C ports to talk to industrial sensors, while the Cortex-A5 plus NEON engine runs Linux with containerized analytics at the edge. The 5 uA backup current preserves battery during grid outages, and ARM TrustZone secures the cryptographic key store from remote management attacks. Typical deployments pair the D23 with a sub-1 GHz radio daughter board or an external LTE modem for cellular uplink, leveraging the same BSP across the product line.
Recommandé
Smart Energy Meters
Smart electricity meters demand long battery-backed retention, signed firmware, and certified metrology accuracy. The ATSAMA5D23B-CN's 5 uA backup current lets the meter survive multi-day power outages while keeping RTC and tamper logs intact, and ARM TrustZone enforces the legal metrology firmware boundary. Its 12-bit ADC, dual sigma-delta interfaces, and on-chip timers allow direct connection to current shunts and voltage dividers, removing the external metering MCU often paired with cheaper MPUs. Compared with discrete MCU + comms-processor designs, the integrated approach shrinks the BOM and reduces calibration drift across temperature.
Recommandé
Building Automation Controllers
Building automation controllers aggregate HVAC, lighting, and access-control sub-systems over KNX, BACnet, Modbus, or Ethernet/IP. The ATSAMA5D23B-CN provides dual CAN-FD plus the EMAC needed to bridge KNX-TP to BACnet/IP in a single IC, while the 500 MHz Cortex-A5 runs Node-RED or a custom automation stack with sufficient headroom for TLS encryption. Its 196-TFBGA footprint enables compact DIN-rail module designs, and the industrial operating temperature range allows deployment in unconditioned electrical closets. Compared with PLC-class controllers, the D23 cuts bill-of-materials cost while retaining deterministic field-bus performance.
Recommandé
Connected Barcode Scanners and POS Terminals
POS terminals and barcode scanners need a balance of imaging throughput, secure payment key handling, and low standby power. The ATSAMA5D23B-CN integrates an image sensor interface (ISI) that connects directly to CMOS barcode sensors at up to 5 Mpixels, while the Cortex-A5 plus NEON engine decodes 1D/2D symbologies in software at sustained 30 fps. ARM TrustZone isolates the PCI payment key store from the general application OS, satisfying PTS POI requirements. The 5 uA backup current keeps the device PIN-authenticated across multi-day store closures, and the USB HS port supports attached payment-terminal peripherals.
Recommandé
Battery-Powered Wearable Medical Devices
Wearable medical devices such as patient monitors and portable infusion pumps demand extended battery life and certified deterministic behavior. The ATSAMA5D23B-CN's 5 uA backup current preserves days of standby on a small Li-ion cell, while the Cortex-A5 runs a safety-certified RTOS or Linux with full MMU protection between trusted medical firmware and connectivity stacks. The integrated audio subsystem supports direct connection to digital stethoscope microphones or pulse-oximeter sensors, eliminating external CODEC ICs. Compared with discrete MCU + audio CODEC designs, the D23 reduces PCB area, which is critical for wrist-worn form factors.
Recommandé
Industrial Printer and Label Maker Controllers
Industrial label printers need fast pixel rendering, USB host connectivity for flash drives, and Ethernet for fleet management. The ATSAMA5D23B-CN integrates an LCD controller that doubles as a print-head buffer interface, while the EMAC and USB HS ports handle print-job upload and flash-drive printing simultaneously. The 128 kbyte L2 cache holds frequently used font tables, eliminating constant DDR fetches during high-speed thermal-head actuation. Compared with separate printer-engine controller + network processor solutions, the D23 reduces component count and simplifies the thermal management of the enclosed print mechanism.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATSAMA5D23B-CN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATSAMA5D23A-CN | ATSAMA5D23B-CNR | ATSAMA5D22B-CUR | ATSAMA5D21B-CU | ATSAMA5D225C-D1M-CU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 196-TFBGA (11x11) | 196-TFBGA (11x11) - same | 196-TFBGA (11x11) - same | 196-TFBGA (11x11) - same | 196-TFBGA (11x11) - same | 196-TFBGA (11x11) - same |
| Core | 1x Cortex-A5 500 MHz | 1x Cortex-A5 500 MHz | 1x Cortex-A5 500 MHz | 1x Cortex-A5 500 MHz | 1x Cortex-A5 500 MHz | 2x Cortex-A5 500 MHz |
| L2 Cache | 128 kbyte | 128 kbyte | 128 kbyte | 64 kbyte | 64 kbyte | 256 kbyte |
| Backup Mode Current | 5 uA | 5 uA | 5 uA | 5 uA | 5 uA | 5 uA |
| Silicon Revision | B | A | B | B | B | C |
| Peripheral Mix | Full (CAN-FD x2, EMAC, USB HS, ISI, audio) | Full - same | Full - same | Reduced | Most reduced | Extended + dual-core |
| Pricing Tier (1 pc) | $14.85 | $13.50 (typical) | $14.85 | $12.10 (typical) | $10.85 (typical) | $22.50 (typical) |
| ARM TrustZone | Yes | Yes | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Revision B silicon with latest errata fixes (vs ATSAMA5D23A-CN)
- Full peripheral mix at lower cost than dual-core D225 (vs ATSAMA5D225C-D1M-CU)
- Larger 128 kbyte L2 cache versus cost-reduced siblings (vs ATSAMA5D21B-CU)
Notes de conception
The 196-TFBGA package uses a 0.8 mm ball pitch, which on a 4-layer PCB allows standard microvia stack-up but still requires laser-via-in-pad for the inner-row balls. Use 1 oz copper on outer layers and 0.5 oz on inner layers; route all signals on the top layer and power on inner layers to maximize thermal dissipation through the BGA land pattern. The Microchip SAMA5D2 hardware design checklist recommends a continuous ground plane under the BGA with no signal traces crossing the keep-out zone.
Estimated: at 500 MHz with both cores active and 1.0 V VDDcore, the ATSAMA5D23B-CN dissipates approximately 0.6-0.9 W depending on workload. The 11x11 TFBGA has a theta_JA around 25 C/W on a 4-layer JEDEC test board, so the junction-to-ambient rise is roughly 15-23 C. For sealed enclosures without forced airflow, derate the clock to 400 MHz or add a small thermal pad to the BGA center balls to keep Tj below 105 C under industrial -40 C to +85 C ambient conditions.
The SAMA5D2 family requires careful power-rail sequencing: VDDCORE must ramp before VDDIO, and the SHDN pin must be held low until both rails are stable. Use the Microchip MIC2800 or equivalent PMIC to provide the 1.0 V core, 1.8 V DDR, and 3.3 V IO rails in the correct order. Add 10 uF + 100 nF decoupling on each rail adjacent to every BGA row, and place a bulk 22 uF tantalum within 25 mm of the chip to handle peak Cortex-A5 load transients during NEON activation.
Do not connect DDR3 power directly to the LPDDR/DDR2/DDR3 reference voltage without a series resistor for output impedance matching - the SAMA5D2 DQS traces must be length-matched within 25 ps. Also, the peripheral touch controller (PTC) requires firmware calibration per PCB; do not skip the production-line calibration routine or touch sensitivity will vary significantly across units. Finally, the backup mode current of 5 uA assumes the RTC crystal ESR is below 60 ohms - higher-ESR crystals can push backup current above 15 uA.
Informations de conformité
RoHS and REACH compliance per Microchip product page; halogen-free status not explicitly listed in verified web data. AEC-Q100 is not applicable to industrial-grade MPUs in this family.