ATSAME53J19A-AU - 120MHz Cortex-M4F MCU | Microchip
Référence : ATSAME53J19A-AU ✓ ActifATSAME53J19A-AU Présentation
A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The Cortex-M4F belongs to the ARM Cortex-M product hierarchy and adds single-precision floating-point instructions to the 32-bit Cortex-M architecture. The ATSAME53 belongs to Microchip's SAM E53 high-performance microcontroller family, combining an Arm processor core with communications, security, and embedded-control capabilities for industrial networking equipment.
Key features include a 120 MHz maximum operating frequency, 512 KB of programmable Flash, 192 KB of SRAM, and a 64-TQFP surface-mount package. The floating-point unit accelerates calculations used in signal processing, control loops, and protocol handling. The 51 I/O functions support external sensors, actuators, status indicators, and communications circuitry, while integrated Ethernet-oriented functionality supports connected industrial equipment. A 1.71 V minimum operating voltage supports low-voltage system designs, while the 3.63 V maximum provides compatibility with standard 3.3 V embedded systems.
The ATSAME53J19A-AU uses a 32-bit Arm Cortex-M4F core with single-precision floating-point hardware. Its architecture supports interrupt-driven real-time control and deterministic peripheral operation. Dual-panel Flash with ECC and SRAM with ECC are listed as capabilities of the SAM E53 family, improving reliability in applications where transient faults matter. The 120 MHz clock rate provides substantial processing headroom for networking stacks, data acquisition, and supervisory control tasks without requiring an external processor.
Typical applications include industrial Ethernet gateways, building-control equipment, networked sensors, data loggers, motor supervisory controllers, and secure embedded gateways. The Ethernet interface makes the device appropriate for equipment that must bridge local sensors to an upper-level network. Its floating-point capability and 192 KB SRAM also suit filtering and real-time measurement tasks, while the 51 available I/O functions reduce the need for external interface expansion.
PCB design should preserve the 1.71 V to 3.63 V operating range with local supply decoupling and verify all signal levels against the device's I/O specifications. The 64-TQFP footprint requires adequate copper area and thermal dissipation for sustained processing workloads. Firmware must also initialize the clock, Ethernet physical interface, security features, and peripheral pins according to the manufacturer datasheet.
This product page combines the exact ordering code, memory and core characteristics, package details, procurement guidance, and application-focused engineering guidance. It also identifies the same-family ordering alternatives that can be evaluated when temperature grade, packaging, or extended-flash-performance requirements differ from the target configuration.
Alternatives de remplacement direct pour ATSAME53J19A-AU — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATSAME53J19A-AU (même facteur de forme et même empreinte) — différant par Package, ADC, Operating Temperature, Operating Voltage, SRAM.
ATSAME53J19A-AFT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATSAME53J19A-AU-EFP
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ATSAME53J19A-MFT
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ATSAME53J19A-AUT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATSAME53J19A-AU Valeurs maximales et caractéristiques électriques
| Product Type | 32-bit ARM Cortex-M4F microcontroller |
| Processor Core | ARM Cortex-M4F with Floating Point Unit |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 512 KB (512K x 8) |
| SRAM | 192 KB |
| Operating Voltage Range | 1.71 V to 3.63 V |
| Number of I/O | 51 I/O |
| Architecture | 32-bit RISC |
| Boîtier | 64-TQFP (10 mm x 10 mm) |
| Type de montage | Surface mount |
| Température de fonctionnement | -40 °C to 85 °C |
| Ethernet Support | Integrated Ethernet-oriented communications functionality |
| Flash ECC | Dual-panel Flash with ECC supported by SAM E53 family |
| SRAM ECC | SRAM with ECC supported by SAM E53 family |
| Shipping Configuration | Tray |
| Statut RoHS | Compliant |
| Series | SAM E53 |
| Qualification Temperature Grade | Industrial temperature grade |
| Nominal System Supply | 3.3 V |
Guide de configuration des broches du ATSAME53J19A-AU 64-tqfp (10 mm x 10 mm)
Configuration des broches du ATSAME53J19A-AU (boîtier 64-tqfp (10 mm x 10 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour ATSAME53J19A-AU.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ATSAME53J19A-AU convient pour 6 applications: Industrial Ethernet Gateway, Building Automation Controller, Networked Data Logger, Motor Monitoring and Control, Secure IoT Sensor Node, Precision Measurement Controller.
Industrial Ethernet Gateway
The ATSAME53J19A-AU fits an industrial Ethernet gateway because its 120 MHz Cortex-M4F core provides capacity for protocol handling, local control, and diagnostics. The 192 KB SRAM supports packet buffering and concurrent tasks, while the 51 I/O functions accommodate status indicators, reset controls, and local sensors. Its 1.71 V to 3.63 V range supports a 3.3 V system architecture. The Ethernet physical interface still requires a suitable transceiver and magnetic network connection, with timing and layout implemented according to the manufacturer reference guidance.
Recommandé
Building Automation Controller
The ATSAME53J19A-AU is suitable for a building-automation controller that combines Ethernet communication with discrete monitoring and control. Its 51 I/O functions can connect sensors, relay drivers, and digital status inputs, while the Cortex-M4F core executes control logic and protocol tasks at up to 120 MHz. A nominal 3.3 V rail falls inside the device's 1.71 V to 3.63 V operating range. Designers should reserve clean supply routing and place decoupling capacitance close to the device pins.
Recommandé
Networked Data Logger
A networked data logger benefits from the ATSAME53J19A-AU's 120 MHz Cortex-M4F processing rate and 192 KB SRAM, which support acquisition routines, local filtering, and data buffering before network transmission. The 512 KB Flash stores firmware and configuration data, while the -40 °C to 85 °C operating range suits standard industrial environments. The device's 51 I/O functions simplify sensor and storage-control connections. Firmware should use ECC-aware memory procedures and provide controlled shutdown behavior for data integrity.
Recommandé
Motor Monitoring and Control
The ATSAME53J19A-AU can supervise a motor system by executing current and speed-control calculations, applying filter algorithms, and coordinating network commands. Its Cortex-M4F single-precision floating-point hardware accelerates control mathematics, while the 51 I/O functions connect position sensors, switch-state inputs, and gate-driver control signals. The 1.71 V to 3.63 V operating range supports compact 3.3 V controller boards. Validate timing margins, isolation boundaries, and thermal performance in the final motor-drive environment.
Recommandé
Secure IoT Sensor Node
The ATSAME53J19A-AU supports an IoT sensor node that must combine local measurement, secure communication, and remote management. Its 120 MHz Cortex-M4F core can process sensor data and communication tasks, while 192 KB SRAM accommodates protocol buffers and application state. The 51 available I/O functions provide flexible connections to sensors and actuators. The SAM E53 family's dual-panel Flash with ECC and SRAM with ECC improves resilience for persistent code and working memory, although exact security-feature configuration must follow the manufacturer documentation.
Recommandé
Precision Measurement Controller
The ATSAME53J19A-AU is appropriate for precision measurement equipment because its Cortex-M4F core supports digital filtering and floating-point calibration calculations. The 120 MHz operating speed can combine acquisition sequencing with communication and supervisory logic, while 192 KB SRAM provides room for sample buffers. A 3.3 V supply is supported by the 1.71 V to 3.63 V operating range. Analog front-end design remains separate from the microcontroller, so grounding, reference-voltage stability, and PCB isolation should be planned together with the digital layout.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATSAME53J19A-AU — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATSAME53J19A-AFT | ATSAME53J19A-AU-EFP | ATSAME53J19A-MFT | ATSAME53J19A-AUT |
|---|---|---|---|---|---|
| Package | 64-TQFP (10 mm x 10 mm) | 64-TQFP (10 mm x 10 mm) | 64-TQFP (10 mm x 10 mm) | 64-TQFP (10 mm x 10 mm) | 64-TQFP (10 mm x 10 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Processor Core | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| Special Configuration | Standard SAM E53 configuration | AFT ordering configuration | Extended flash performance | MFT ordering configuration | Tape-and-reel ordering configuration |
Principaux différenciateurs
- Exact 512 KB Flash configuration in the 64-TQFP footprint (vs ATSAME53J19A-AFT)
- Standard industrial ordering configuration for ATSAME53J19A-AU (vs ATSAME53J19A-AU-EFP)
- Tray configuration matches the target procurement format (vs ATSAME53J19A-AUT)
- 192 KB SRAM supports simultaneous control and communication work (vs ATSAME53J19A-MFT)
Notes de conception
Design the supply rail for the device's 1.71 V to 3.63 V operating range and place the required input and output capacitors close to their associated pins. Keep high-current Ethernet transceiver and magnetic-interface supplies separate from sensitive analog returns wherever the system architecture permits. Confirm startup, brownout, and regulator tolerance requirements against the Microchip electrical-characteristics documentation before releasing the power design.
Route clocks, programming signals, debug interfaces, and communication lines away from noisy switching nodes. Maintain continuous ground references beneath signal paths and use the 64-TQFP land pattern exactly as defined by the manufacturer package drawing. Ethernet magnetics and high-speed differential routing require controlled impedance and short return paths; follow the Microchip reference design and Ethernet-interface layout guidance for the final stack-up.
The 120 MHz Cortex-M4F operating rate and Ethernet activity can increase device power dissipation during sustained computation. Provide adequate PCB copper around the TQFP leads, control thermal exposure across the -40 °C to 85 °C range, and avoid enclosing the assembly without thermal analysis. Validate junction temperature with the actual processor loading, supply voltage, board construction, and enclosure rather than relying only on ambient temperature.
Do not assume that every one of the 51 I/O functions can be assigned independently; package pins also carry power, clock, reset, debug, programming, and communications functions. Review the complete pin-description table before allocating a peripheral. Likewise, verify the distinction between ATSAME53J19A-AU and suffix variants so that tray, tape-and-reel, temperature-grade, and extended-performance conditions do not change unexpectedly.
Keep the 120 MHz clock route short and return it through a continuous ground reference, and place clock-support components according to the manufacturer recommended layout. Provide unobstructed access to programming and debug signals for manufacturing and field updates. If the Ethernet interface uses an external transceiver, isolate its digital and analog supply paths to prevent communication activity from disturbing measurement or control signals.
Informations de conformité
The product listing identifies the ATSAME53J19A-AU as RoHS compliant. No separate REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification declaration is available for this ordering code.