ATXMEGA32D3-AN - 32MHz 32KB Flash 64-TQFP AVR MCU | Microchip
Référence : ATXMEGA32D3-AN ✓ ActifATXMEGA32D3-AN Présentation
The ATXMEGA32D3 belongs to the XMEGA family of AVR microcontrollers, combining a 16-bit RISC instruction set with a Harvard-style memory architecture, event system, programmable multi-level interrupt controller, and dedicated peripheral resources. Its 50 general-purpose I/O lines make it suitable for control panels, instrumentation, communication gateways, and low-power embedded systems.
The device operates from 1.6 V to 3.6 V and supports a four-channel event system, a 16-bit real-time counter, five flexible 16-bit timer/counters with compare modes and PWM, and a hardware multiplier. These resources support precise timing, motor control, signal capture, and asynchronous event-driven system operation without requiring external logic.
A key architectural advantage is read-while-write Flash operation, allowing code to be updated through ISP programming while the application continues operating from another Flash section. The boot-code section also supports controlled startup behavior and firmware organization for field-updateable products.
Typical applications include industrial data acquisition, building automation, battery-powered sensing nodes, compact motor controllers, USB interface systems, and general-purpose AVR-compatible control boards. The large I/O count and flexible timer resources are particularly valuable when consolidating discrete logic into a single microcontroller.
When laying out the PCB, follow the manufacturer pinout and decoupling recommendations, keep the supply and ground planes continuous, and reserve the programming and boot interfaces. Because the 64-TQFP footprint is fine-pitch, verify land patterns against the package drawing and inspect assemblies for bridging on closely spaced leads. This page combines manufacturer specifications, distributor availability references, drop-in alternatives, and practical design guidance for engineers evaluating the ATXMEGA32D3-AN.
Alternatives de remplacement direct pour ATXMEGA32D3-AN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATXMEGA32D3-AN (même facteur de forme et même empreinte) — différant par Flash Memory, Package, EEPROM Memory, Timer/Counters.
ATXMEGA32D3-AU
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →ATXMEGA32D4-AN
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →ATXMEGA64A3U-ANR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATXMEGA16D4-ANR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATXMEGA128A3U-AU
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATXMEGA32D3-AN Valeurs maximales et caractéristiques électriques
| Core Architecture | 8/16-bit AVR XMEGA RISC |
| Maximum Clock Speed | 32 MHz |
| Flash Memory | 32 KB ISP Flash |
| Boot Code Section | 4 KB |
| EEPROM Memory | 2 KB |
| SRAM | 4 KB |
| General-Purpose I/O Lines | 50 |
| Supply Voltage Range | 1.6 V to 3.6 V |
| Event System Channels | 4 |
| Real-Time Counter | 16-bit |
| Timer/Counter Units | 5 flexible 16-bit timer/counters with compare modes and PWM |
| Interrupt Controller | Programmable multi-level interrupt controller |
| Flash Programming | ISP Flash with read-while-write capability |
| Boîtier | 64-TQFP, 14 x 14 mm |
| Type de montage | Surface Mount |
| Green / Environmental Design | Green |
| Temperature Rating | 105 C |
Guide de configuration des broches du ATXMEGA32D3-AN 64-tqfp, 14 x 14 mm
Configuration des broches du ATXMEGA32D3-AN (boîtier 64-tqfp, 14 x 14 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour ATXMEGA32D3-AN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ATXMEGA32D3-AN convient pour 7 applications: Industrial Data Acquisition, Building Automation Controller, Battery-Powered Sensor Node, Compact Motor Controller, USB Communication Interface, Programmable Logic Instrument, Real-Time Control and Timing Hub.
Industrial Data Acquisition
The ATXMEGA32D3-AN suits compact acquisition and control boards because it combines a 32 MHz AVR XMEGA core with 50 general-purpose I/O lines, five 16-bit timer/counters, and a four-channel event system. Those resources can capture sensor events, drive digital isolators, operate status indicators, and time external measurements without a companion logic device. Its 4 KB SRAM and 32 KB ISP Flash are adequate for moderate local buffering, while the 1.6 V to 3.6 V operating range allows integration with low-voltage front ends. For precision analog acquisition, add a suitable external ADC and route its reference and ground connections according to the system signal-integrity requirements.
Recommandé
Building Automation Controller
The ATXMEGA32D3-AN is appropriate for distributed building-automation nodes where a controller must manage sensors, relay logic, and communication interfaces within a constrained power budget. Its 50 I/O lines reduce the need for external I/O expanders, while the event system can connect timer, counter, and communication events without busy-waiting. The 16-bit timers support periodic maintenance cycles, debounce timing, and PWM-based actuator control. Its 1.6 V minimum supply voltage also allows operation from regulated industrial rails. The designer should define fail-safe states for relays and validate timing during power restoration before deploying the controller as a safety-relevant building component.
Recommandé
Battery-Powered Sensor Node
A low-voltage sensor node can use the ATXMEGA32D3-AN's 1.6 V to 3.6 V operating range to simplify power-supply design around small energy-harvesting or battery sources. The 32 MHz AVR XMEGA core supports responsive control, while five flexible 16-bit timer/counters and PWM outputs can manage excitation timing or motor-driven sampling. The 4 KB SRAM is sufficient for short sensor records, and 2 KB EEPROM preserves calibration parameters. Firmware should use the device's sleep and clock-control facilities to minimize active energy, while the PCB should isolate analog sensors from digital switching paths. External low-leakage regulators and sensors will often dominate total node power.
Recommandé
Compact Motor Controller
The ATXMEGA32D3-AN can supervise compact motor systems where multiple PWM outputs, precise timing, and event-driven control are needed. Its five 16-bit timer/counters provide compare and PWM functions that can generate control signals for gate drivers, while the 16-bit real-time counter supports position or period measurement. Fifty I/O lines leave ample pins for Hall sensors, limit switches, status LEDs, and communications. The MCU itself is not a high-power motor driver; it must drive external MOSFET or intelligent-driver stages. Add fault handling for overcurrent, overtemperature, and stalled-load conditions so that a software fault cannot leave the power stage energized.
Recommandé
USB Communication Interface
The ATXMEGA32D3-AN can serve as the protocol controller in a compact USB interface module when its 32 MHz execution rate and 50 I/O lines are adequate for the required data rate. The programmable interrupt controller and event system help coordinate USB traffic with application tasks, while the ISP Flash permits field-updatable firmware. Designers should use the manufacturer’s USB electrical recommendations, including controlled-impedance routing and suitable protection. An external transceiver or USB switch may be needed for a complete interface, and enumeration behavior should be verified against the target USB class and host requirements. The ATXMEGA32D3-AN is therefore best treated as an application processor rather than a dedicated USB PHY.
Recommandé
Programmable Logic Instrument
The ATXMEGA32D3-AN fits programmable measurement instruments that require many digital controls, event sequencing, and moderate local processing. Its 16-bit timer/counters can time sample intervals or generate stimulus waveforms, and the 50 I/O lines can control relays, attenuators, and front-panel indicators. The read-while-write Flash capability supports in-system firmware updates, while the boot-code section provides a controlled path for initialization or recovery logic. For precision analog measurements, pair the controller with a dedicated converter such as the MCP3424. Keep analog and digital ground returns disciplined, and isolate high-energy switching stages from sensitive measurement paths to avoid corrupting the sampled signal.
Recommandé
Real-Time Control and Timing Hub
The ATXMEGA32D3-AN is useful when several time-critical events must be coordinated without excessive polling. Its four-channel event system can route signals between timer/counter units and other peripherals, while the programmable multi-level interrupt controller allows priority-based event handling. The 16-bit real-time counter provides a dedicated timing reference, and five timer/counters support independent periods, compare events, and PWM generation. This arrangement is appropriate for distributed motor timing, sampling triggers, and periodic control loops. Firmware should use atomic access and documented interrupt-latency expectations around shared timers, and the clock tree should be configured to preserve the required timing resolution.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATXMEGA32D3-AN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATXMEGA32D3-AU | ATXMEGA32D4-AN | ATXMEGA64A3U-ANR | ATXMEGA16D4-ANR | ATXMEGA128A3U-AU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (14x14) | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same |
| Ordering/Packing Suffix | -AN | -AU | -AN | -ANR | -ANR | -AU |
Principaux différenciateurs
- Direct match within the ATxmega32D3 device family (vs ATXMEGA32D3-AU)
- Substantially larger Flash option in the same TQFP format (vs ATXMEGA128A3U-AU)
- Balanced memory capacity for firmware growth (vs ATXMEGA64A3U-ANR)
- Purpose-built event and timing subsystem (vs ATXMEGA16D4-ANR)
Notes de conception
Use the manufacturer 64-TQFP land pattern and pin-1 orientation markings when defining the footprint. Place the MCU close to its supply bypass capacitor, route the ground and power rails as continuous planes, and keep high-speed or high-current switching nodes away from adjacent ADC and communication inputs. Inspect the fine-pitch perimeter leads for solder bridging, and verify the assembled board against the package drawing rather than relying only on the generic TQFP dimensions.
Design the 1.6 V to 3.6 V supply so that its transient behavior remains inside the device's operating requirements. Follow the manufacturer's recommended supply and bypass-capacitor arrangement, provide a stable return path, and avoid placing noisy switching stages directly beneath sensitive MCU pins. If the board combines a 3.3 V rail with low-voltage peripherals, use the device's brownout, clock, and power-control features to manage startup and voltage transitions.
Do not assume that the 64-TQFP package alone proves drop-in compatibility between ATxmega32D3, ATxmega32D4, and ATxmegaA3 devices. Peripheral mappings, alternate functions, memory sizes, and interrupt behavior differ by device family, while the ordering suffix can change temperature or packing. Before substitution, compare the manufacturer pin-description table, check the application firmware, and confirm the required Flash and SRAM capacity for the released software image.
The event system and timer resources can reduce the need for polling, but external trigger and sensor signals still need careful conditioning. Keep edge-sensitive inputs short, use ground guarding where appropriate, and separate analog and digital return currents to reduce converter noise in measurements. When using the 32 MHz clock, confirm that clock-source layout, startup behavior, and load capacitors follow the manufacturer's guidance rather than copying a generic oscillator circuit.
Informations de conformité
The distributor listing identifies the device as Green and a 105 C grade part. RoHS, REACH, halogen-free, and conflict-minerals declarations were not explicitly stated, so those fields remain unknown.
