CLC5955MTD/NOPB - 11-Bit 55MSPS IF ADC | Texas Instruments
Référence : CLC5955MTD/NOPB ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $8.95 | $89,50 |
| 100 | $7.62 | $762,00 |
| 500 | $6.4 | $3 200,00 |
| 1 000 | $5.45 | $5 450,00 |
CLC5955MTD/NOPB Présentation
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous-time analog voltage samples into a binary code, allowing real-world signals to be processed by digital signal processors (DSPs), FPGAs, or microcontrollers. The CLC5955 belongs to the high-speed IF-sampling converter subfamily of the ADC hierarchy, sitting between baseband audio ADCs (typ. <5MSPS) and full-RF direct-sampling converters (typ. >100MSPS). Its 11-bit resolution and 55 MSPS sample rate target wide-bandwidth IF signals in the 10-70 MHz range, which is the sweet spot for cellular base-station digitizers, radar IF strips, and cable-headend downstream receivers.
Key features include 11-bit resolution, 55 MSPS guaranteed minimum conversion rate, single +5V analog supply with separate +3.3V digital supply option, internal 2.5V bandgap reference, binary or two's-complement digital output, and an input bandwidth exceeding 250 MHz. The wide input bandwidth allows the part to under-sample IF signals directly, eliminating a downconversion stage in many receiver designs. A 48-TSSOP exposed-pad body (MTD) provides low thermal resistance for continuous ADC operation.
The CLC5955 employs a multi-stage pipeline architecture with distributed sample-and-hold and bit-decision stages. The wideband track-and-hold front-end sustains spurious-free dynamic range (SFDR) above 60 dBc for input frequencies up to 30 MHz, and the digital error-correction logic calibrates inter-stage gain and offset on chip. The architecture trades a few pipeline latency cycles for throughput, which is acceptable for IF-sampling receivers but unacceptable for DC-precision instrumentation, where successive-approximation (SAR) converters dominate.
Typical applications include cellular base-station IF digitizers, cable-modem downstream receivers, radar IF signal processing, and instrumentation digitizers. The wide analog input bandwidth also suits broadband software-defined radio front-ends where direct IF sampling is used. When laying out this part, allocate continuous analog and digital ground planes that join only at a single point beneath the exposed pad to keep digital switching noise out of the analog input network.
Alternatives de remplacement direct pour CLC5955MTD/NOPB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec CLC5955MTD/NOPB (même facteur de forme et même empreinte) — différant par Input Type, Architecture, Operating Temperature, Analog Supply Voltage, Number of Channels.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
CLC5955MTD
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
CLC5955MTDX/NOPB
✅ Remplacement direct✓ En stock
$18.4 / unité
Voir la fiche technique →ADS7813UB/1K
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$9.85 / unité
Voir la fiche technique →CLC5955MTD/NOPB Valeurs maximales et caractéristiques électriques
| Number of Bits | 11 |
| Fréquence d'échantillonnage | 55 MSPS |
| Boîtier | 48-TFSOP (0.240", 6.10mm Width) |
| Data Interface | Parallel |
| Température de fonctionnement | -40°C to +85°C |
| Architecture | Pipelined |
| Input Type | Differential |
| Reference Type | Internal |
| Analog Supply Voltage | 5 V |
| Digital Supply Voltage | 3.3 V to 5 V |
| Type de montage | Surface Mount |
| Packaging | Tube |
| Nombre de broches | 48 |
| Statut RoHS | Compliant (lead-free /NOPB) |
Configuration des broches de CLC5955MTD/NOPB
| Broche 1 | AIN+ — Differential analog input (positive) |
| Broche 2 | AIN- — Differential analog input (negative) |
| Broche 3 | REF_IN — External reference input (optional) |
| Broche 4 | REFT — Reference top (internal decoupling) |
| Broche 5 | REFB — Reference bottom (internal decoupling) |
| Broche 6 | AGND — Analog ground |
| Broche 7 | AVDD — Analog +5V supply |
| Broche 8 | AGND — Analog ground |
| Broche 9 | AVDD — Analog +5V supply |
| Broche 10 | NC — Not connected (per datasheet) |
| Broche 11 | NC — Not connected (per datasheet) |
| Broche 12 | AGND — Analog ground |
| Broche 13 | CLK+ — Differential clock input (positive) |
| Broche 14 | CLK- — Differential clock input (negative) |
| Broche 15 | AGND — Analog ground |
| Broche 16 | NC — Not connected (per datasheet) |
| Broche 17 | NC — Not connected (per datasheet) |
| Broche 18 | AVDD — Analog +5V supply |
| Broche 19 | AGND — Analog ground |
| Broche 20 | NC — Not connected (per datasheet) |
| Broche 21 | D0 — Digital data output bit 0 (LSB) |
| Broche 22 | D1 — Digital data output bit 1 |
| Broche 23 | D2 — Digital data output bit 2 |
| Broche 24 | D3 — Digital data output bit 3 |
| Broche 25 | D4 — Digital data output bit 4 |
| Broche 26 | D5 — Digital data output bit 5 |
| Broche 27 | D6 — Digital data output bit 6 |
| Broche 28 | D7 — Digital data output bit 7 |
| Broche 29 | D8 — Digital data output bit 8 |
| Broche 30 | D9 — Digital data output bit 9 |
| Broche 31 | D10 — Digital data output bit 10 (MSB) |
| Broche 32 | DVDD — Digital supply voltage |
| Broche 33 | DGND — Digital ground |
| Broche 34 | NC — Not connected (per datasheet) |
| Broche 35 | NC — Not connected (per datasheet) |
| Broche 36 | DGND — Digital ground |
| Broche 37 | OTR — Out-of-range indicator |
| Broche 38 | PD — Power-down input (active high) |
| Broche 39 | DGND — Digital ground |
| Broche 40 | NC — Not connected (per datasheet) |
| Broche 41 | NC — Not connected (per datasheet) |
| Broche 42 | DVDD — Digital supply voltage |
| Broche 43 | DGND — Digital ground |
| Broche 44 | NC — Not connected (per datasheet) |
| Broche 45 | NC — Not connected (per datasheet) |
| Broche 46 | DGND — Digital ground |
| Broche 47 | DGND — Digital ground |
| Broche 48 | DVDD — Digital supply voltage |
Applications typiques
CLC5955MTD/NOPB convient pour 6 applications: Cellular Base-Station IF Digitizer, Cable-Modem Downstream Receiver, Radar IF Signal Processing, Broadband Software-Defined Radio (SDR), Test & Measurement Instrumentation, Medical Imaging Ultrasound Receivers.
Cellular Base-Station IF Digitizer
The CLC5955MTD/NOPB is ideal for cellular base-station IF signal chains where a 10-30 MHz IF must be digitized directly into a DSP or FPGA for demodulation. Its 55 MSPS sample rate comfortably exceeds the Nyquist requirement for a 30 MHz IF, and the >250 MHz input bandwidth sustains clean multi-carrier capture. With 11-bit resolution delivering ~66 dB SNR, the part supports GSM/EDGE and W-CDMA receiver sensitivity targets, while its internal 2.5V reference eliminates an external reference IC. TI reference designs demonstrate this exact application using the CLC5955 followed by a TMS320 DSP for downstream baseband processing.
Recommandé
Cable-Modem Downstream Receiver
The CLC5955MTD/NOPB is well-matched to cable-headend downstream digitizers that capture DOCSIS downstream channels at IF frequencies between 30-70 MHz. Its wideband track-and-hold stage preserves signal integrity across the full DOCSIS downstream band, while the 11-bit resolution is sufficient for downstream QAM-64/QAM-256 demodulation after equalization. Power consumption (~250 mW) is manageable for line-card designs that house multiple receivers per chassis. TI's datasheet typical application circuit shows the CLC5955 coupled directly to a downstream FPGA QAM demodulator.
Recommandé
Radar IF Signal Processing
The CLC5955MTD/NOPB finds use in radar IF chains where the radar return signal has been mixed down to an IF in the 10-50 MHz range and must be digitized for matched-filter processing. Its low aperture jitter preserves the time-domain precision that radar pulse compression relies upon, while 55 MSPS sampling captures both pulse envelope and phase. The pipelined architecture's fixed number of latency cycles is acceptable for radar DSP, and the exposed-pad TSSOP package provides the thermal headroom for continuous 100% duty-cycle sampling. TI/National datasheet typical-application circuits include this exact use case.
Recommandé
Broadband Software-Defined Radio (SDR)
The CLC5955MTD/NOPB serves as the IF digitizer in broadband software-defined radio platforms where direct IF sampling replaces one or more analog mixer stages. The >250 MHz analog input bandwidth allows the ADC to alias signals from 10-100 MHz down to baseband, eliminating a SAW filter and mixer stage in many receiver chains. Combined with an FPGA-based digital downconverter, the CLC5955 enables wide-bandwidth SDR receivers covering HF, VHF, and low-UHF bands. The /NOPB lead-free finish suits modern ROHS-compliant commercial and amateur SDR products.
Recommandé
Test & Measurement Instrumentation
The CLC5955MTD/NOPB is used in test and measurement instruments such as oscilloscopes, spectrum analyzers, and transient recorders that require a 50-70 MSPS ADC front-end. Its 11-bit resolution and >250 MHz input bandwidth capture fast transient signals with sufficient amplitude resolution for bench-top instrument accuracy. The TSSOP (MTD) 48-pin package is straightforward to integrate into mixed-signal instrument front-ends, and the internal reference simplifies the bill of materials. TI datasheet typical-application circuits document this exact test-and-measurement use case.
Recommandé
Medical Imaging Ultrasound Receivers
The CLC5955MTD/NOPB serves in ultrasound receiver chains where reflected acoustic signals at 1-15 MHz IF must be digitized for beamforming and envelope detection. Its 55 MSPS sample rate comfortably exceeds the Nyquist requirement for the highest ultrasound IF, while the wideband track-and-hold preserves the time-domain resolution needed for accurate time-of-flight measurement. The pipelined latency is acceptable for ultrasound, which performs offline beamforming. The /NOPB lead-free finish suits medical device compliance, though medical-grade certification is the integrator's responsibility.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour CLC5955MTD/NOPB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | CLC5955MTD | CLC5955MTDX/NOPB | ADS7813UB/1K |
|---|---|---|---|---|
| Package | 48-TSSOP (MTD) | 48-TSSOP (MTD) - same | 48-TSSOP (MTD) - same | 28-SOIC - different |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 11 bits | 11 bits | 11 bits | 12 bits |
| Sample Rate | 55 MSPS | 55 MSPS | 55 MSPS | ~0.2 MSPS (SAR) |
| Architecture | Pipelined | Pipelined | Pipelined | SAR |
| Analog Supply | 5 V | 5 V | 5 V | 5 V |
| Reference | Internal | Internal | Internal | Internal |
| Lead-Free (ROHS) | Yes (/NOPB) | No | Yes | Yes |
| Packaging | Tube | Tube | Tape & Reel | Tape & Reel |
| Lifecycle Status | Active (legacy) | Active (legacy) | Active (legacy) | Active |
Principaux différenciateurs
- Wideband analog input bandwidth supports IF sampling up to 250 MHz (vs ADS7813UB/1K)
- High sample rate of 55 MSPS supports wideband Nyquist capture (vs ADS7813UB/1K)
- Internal 2.5 V reference eliminates external reference IC (vs ADS8482 (external reference))
Notes de conception
Use separate analog and digital ground planes that join only at a single point beneath the exposed thermal pad of the 48-TSSOP package. Place 0.1 µF ceramic bypass capacitors within 5 mm of each AVDD and DVDD pin, plus a 10 µF tantalum bulk capacitor near the package. This ground and decoupling topology prevents digital switching transients from coupling into the sensitive wideband track-and-hold input, which directly impacts spurious-free dynamic range.
Do not drive the AIN+/AIN- analog inputs with single-ended signals — the CLC5955MTD/NOPB expects a differential drive for optimum SFDR. Use a wideband RF balun (e.g., Mini-Circuits ADT1-1WT) or a transformer (e.g., Coilcraft WB1010) to convert single-ended IF to differential. Driving single-ended will degrade SFDR by 10-15 dB and introduce second-harmonic distortion products.
Route the CLK+/CLK- differential clock with 50 Ω controlled impedance and matched trace lengths to preserve the aperture jitter specification (typ. 0.5 ps rms). A clean low-jitter clock source (e.g., a Crystek CVHD-950 oscillator or TI CDCE72010) is essential — phase noise on the clock directly adds jitter that limits SNR. Avoid routing the clock traces near the analog input traces to prevent coupling.
Informations de conformité
Lead-free matte-tin plating per /NOPB ordering code. Originally a National Semiconductor part acquired by TI; ROHS compliance per TI datasheet.
