Infineon

CY7C68000A-56LFXC USB 2.0 Transceiver | Infineon Technologies

Référence : CY7C68000A-56LFXC ✓ Actif
Single transceiver Vdss 56-pin QFN, 8 mm x 8 mm Package
MOQ : 1 |

CY7C68000A-56LFXC Présentation

The Infineon Technologies CY7C68000A-56LFXC is a full-speed USB 2.0 transceiver with serial and parallel interfaces, supplied in a 56-pin QFN package measuring 8 mm by 8 mm. It supports a 16-bit parallel interface operating at 30 MHz or an 8-bit parallel interface operating at 60 MHz, giving designers flexibility when connecting USB 2.0 physical-layer signaling to programmable logic, an embedded controller, or an FPGA.

A USB transceiver is an interface semiconductor that converts between serial differential USB signaling and a parallel digital data bus. It belongs to the USB interface controller ecosystem and broader interface IC category, providing the physical-layer path between a host or device controller and an external USB connector. The parallel interface simplifies integration with programmable hardware while retaining compatibility with USB 2.0 full-speed operation.

The CY7C68000A-56LFXC supports USB 2.0 test modes and is identified as a 1/1 full USB 2.0 transceiver. The device can accommodate two parallel-interface configurations: 16 bits at 30 MHz and 8 bits at 60 MHz. This selectable operating arrangement is useful when balancing bus width, clocking requirements, FPGA resource use, and data throughput in USB connectivity designs.

The MoBL-USB TX2 architecture integrates the USB serial transmitter and receiver with a parallel data interface. In one supported configuration, sixteen parallel bits are transferred at 30 MHz; in the other, eight parallel bits are transferred at 60 MHz. Both modes present the same 60 million bit-per-second parallel transfer rate while allowing the system designer to choose between a wider, slower bus and a narrower, faster bus.

Typical uses include USB-to-FPGA gateways, test and measurement systems, industrial data-acquisition equipment, USB peripheral controllers, and embedded USB connectivity platforms. The 56-QFN package supports compact, high-density PCB layouts, but its exposed thermal pad and high-speed interfaces require careful footprint, solder, and return-path design.

For implementation, preserve the differential impedance of the USB D+ and D- connection, provide continuous return paths beneath high-speed traces, and follow the manufacturer pin-description table when assigning every QFN terminal. Use the exposed-pad land pattern and paste geometry specified by the manufacturer rather than substituting a generic 56-QFN footprint.

This product page combines the manufacturer interface capabilities, package information, and verified replacement references with application-specific implementation guidance. It helps engineers distinguish the two parallel operating modes, identify meaningful same-family alternatives, and plan a USB 2.0 transceiver layout before committing a new board to production.

Alternatives de remplacement direct pour CY7C68000A-56LFXC — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec CY7C68000A-56LFXC (même facteur de forme et même empreinte) — différant par USB Specification, Architecture, Maximum USB Data Rate, Package, Package Type.

Infineon
Package: 56-QFN (8 mm x 8 mm)
Package Type: QFN with exposed pad
Comparer avec CY7C68000A-56LFXC →
Infineon
USB Specification: USB 2.0 full-speed
Architecture: Serial/deserializer to parallel interface
Maximum USB Data Rate: 12 Mbit/s
Comparer avec CY7C68000A-56LFXC →

CY7C68000A-56LTXC

✅ Remplacement direct
📦 56-QFN (8 mm x 8 mm)
Same 56-QFN USB 2.0 transceiver package and 480 Mbps class; ordering suffix differs, so confirm pin assignment and ordering details before substitution.

📋 Alternative de référence (hors catalogue)

CY7C68000-56LFXC

✅ Remplacement direct
Infineon
📦 56-QFN (8 mm x 8 mm)
USB 2.0 transceiver · 1 transmit and 1 receive channel · USB 2.0 · USB differential serial interface · 16 bits or 8 bits · 30 MHz · 60 MHz · 56-QFN (8 mm x 8 mm)

Contactez-nous pour le prix

Voir la fiche technique →

CY7C68000A-56LFXC Spécifications

Device Type 1/1 USB 2.0 transceiver
USB Specification USB 2.0
Maximum USB Data Rate 480 Mbps
Wide Parallel Interface 16 bits at 30 MHz
Narrow Parallel Interface 8 bits at 60 MHz
Parallel Transfer Rate 60 Mbit/s
Test Mode Support USB 2.0 test modes
Boîtier 56-pin QFN, 8 mm x 8 mm
Terminal Count 56 terminals
Package Code HVQCCN
Package Shape Square
Style de montage No-lead surface mount
Temperature Grade Commercial
Supply Configuration Single transceiver
Architecture MoBL-USB TX2 USB 2.0 UTMI transceiver
Serializer/Deserializer Support Yes

Guide de configuration des broches du CY7C68000A-56LFXC square

Configuration des broches du CY7C68000A-56LFXC (boîtier square). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier square pour le CY7C68000A-56LFXC

Aucune donnée de brochage détaillée disponible pour CY7C68000A-56LFXC.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

CY7C68000A-56LFXC convient pour 6 applications: FPGA USB 2.0 Data Gateway, USB Test and Measurement Equipment, Industrial USB Data Acquisition, Embedded USB Peripheral Controller, USB-to-Parallel Protocol Bridge, USB Protocol Development Platform.

🖥️

FPGA USB 2.0 Data Gateway

The CY7C68000A-56LFXC fits an FPGA-based USB gateway because the manufacturer supports both a 16-bit interface at 30 MHz and an 8-bit interface at 60 MHz. The selected mode determines how many FPGA I/O resources are committed to the parallel bus and how tightly the internal clocking must be constrained. Its 60 Mbit/s parallel transfer rate supports a practical division of labor between the USB physical interface and user-defined FPGA logic. Preserve a continuous ground reference beneath the USB D+ and D- pair, route the pair as a coupled differential pair, and use the manufacturer QFN land pattern and exposed-pad geometry.

🔧

USB Test and Measurement Equipment

The CY7C68000A-56LFXC is appropriate for USB connectivity in test and measurement equipment because it supports USB 2.0 test modes alongside the standard full-speed serial interface. Its parallel bus can be configured as 16 bits at 30 MHz for straightforward data capture or 8 bits at 60 MHz for narrower implementations. Test-mode behavior, serial descriptors, and loopback states should follow the manufacturer datasheet and applicable USB 2.0 procedures. Keep sensitive analog and reference circuitry physically separated from the USB pair, and provide low-impedance supply and ground connections to minimize susceptibility to test-bench noise.

🏭

Industrial USB Data Acquisition

The CY7C68000A-56LFXC can serve as the USB physical interface in an industrial data-acquisition controller where a parallel logic connection is preferable to a direct serial processor peripheral. The manufacturer-described 16-bit-at-30-MHz and 8-bit-at-60-MHz modes give the controller designer flexibility to balance register bandwidth against wiring density. The commercial-grade designation requires comparison with the enclosure's temperature range before production release. Maintain continuous ground planes, place bypass capacitors near their assigned device pins, and isolate the USB differential route from high-current switching stages to preserve signal integrity.

🧩

Embedded USB Peripheral Controller

The CY7C68000A-56LFXC is suitable for an embedded USB peripheral controller that separates USB physical signaling from an internal parallel bus. At 8 bits and 60 MHz, the interface can connect to faster internal logic, while the 16-bit mode at 30 MHz offers a wider data path that may simplify certain register or datapath implementations. Because both modes have the same stated parallel transfer rate, the selection should follow timing closure, available I/O, and routing constraints. Follow the terminal table exactly and expose the device's exposed-pad thermal connection according to the manufacturer package drawing.

🌐

USB-to-Parallel Protocol Bridge

The CY7C68000A-56LFXC can bridge a USB 2.0 full-speed connection to an external parallel subsystem when the destination device expects a synchronous bus. The choice between 16 bits at 30 MHz and 8 bits at 60 MHz provides a meaningful hardware-design choice: wider buses can reduce signal count, while narrower buses can align more closely with high-speed internal logic. Build clocking and data-valid handling around the selected mode in the manufacturer datasheet. Route the parallel nets as short, properly terminated paths and keep the USB pair away from clocks, switching nodes, and other potential aggressors.

⚡

USB Protocol Development Platform

The CY7C68000A-56LFXC supports USB protocol development because it combines a full-speed USB 2.0 physical interface with two selectable parallel widths. Developers can use the 16-bit mode to simplify capture logic or the 8-bit mode to explore faster parallel timing, while USB 2.0 test-mode support assists in validation. The 56-QFN package permits compact implementation but leaves little tolerance for an improvised footprint or pad design. Reproduce the manufacturer terminal map and exposed-pad geometry, include test access to D+ and D-, and preserve short return paths beneath the differential pair.

What is the CY7C68000A-56LFXC?
The CY7C68000A-56LFXC is an Infineon Technologies full-speed USB 2.0 transceiver with a parallel digital interface. According to the manufacturer datasheet, it serializes and deserializes USB signals for a 16-bit interface at 30 MHz or an 8-bit interface at 60 MHz. The device is packaged in a 56-pin QFN measuring 8 mm by 8 mm and is intended for controller, FPGA, test, and embedded USB interface designs.
What parallel interface modes does the CY7C68000A-56LFXC support?
The CY7C68000A-56LFXC supports two parallel-interface arrangements: 16 bits at 30 MHz and 8 bits at 60 MHz. According to the manufacturer datasheet, both modes correspond to the same 60 Mbit/s parallel transfer rate. Designers can therefore choose a wider bus for easier routing and logic use or a narrower bus for a higher parallel clock frequency.
Where can I download the CY7C68000A-56LFXC datasheet PDF?
The CY7C68000A-56LFXC datasheet PDF is available from the manufacturer document link listed on this page. It describes the MoBL-USB TX2 USB 2.0 UTMI transceiver, its 16-bit-at-30-MHz and 8-bit-at-60-MHz operating modes, USB 2.0 test-mode support, package information, and the pin-description and electrical tables required for schematic and PCB development.
Where is the CY7C68000A-56LFXC pinout?
The CY7C68000A-56LFXC pinout is defined in the pin-description table of the manufacturer datasheet. The device uses a 56-terminal, no-lead square QFN package with package code HVQCCN. Use that table when assigning USB differential terminals, parallel data, clocks, control signals, supplies, grounds, and exposed-pad connections; do not infer terminal assignments from a generic 56-QFN symbol.
What is the maximum USB data rate of the CY7C68000A-56LFXC?
The CY7C68000A-56LFXC supports USB 2.0 signaling at up to 480 Mbps. According to the manufacturer datasheet, its parallel side operates at 60 Mbit/s in either the 16-bit-at-30-MHz mode or the 8-bit-at-60-MHz mode. The 480-Mbps figure describes the USB 2.0 specification supported by the transceiver rather than the parallel clock frequency.
Can CY7C68000A-56LTXC replace the CY7C68000A-56LFXC?
The CY7C68000A-56LTXC is the closest documented same-family replacement for the CY7C68000A-56LFXC. Comparison records identify both as USB 2.0 transceivers in 56-pin QFN packages with the same 480-Mbps classification. Before substitution, verify the exact terminal assignments, temperature limits, ordering suffix, and exposed-pad requirements against the manufacturer datasheet for the specific board revision.
What is the best drop-in replacement for the CY7C68000A-56LFXC?
The CY7C68000A-56LTXC is the best-supported drop-in candidate identified for the CY7C68000A-56LFXC because both use the 56-pin QFN format and are classified as USB 2.0, 480-Mbps transceivers. A lower-frequency CY7C68000-56LFXC family member is another same-package option, but confirm device revision, pin configuration, and operating requirements before using it on an existing design.
Is the CY7C68000A-56LFXC suitable for an FPGA-based USB interface?
The CY7C68000A-56LFXC is suitable for an FPGA-based USB interface because its parallel bus can be configured for 16 bits at 30 MHz or 8 bits at 60 MHz. According to the manufacturer datasheet, this flexibility allows the FPGA logic interface to match the selected bus width. The design must still use the exact QFN footprint and preserve controlled-impedance routing on the USB differential pair.
How should I choose between the 16-bit and 8-bit modes of the CY7C68000A-56LFXC?
Choose the 16-bit-at-30-MHz mode when the FPGA or controller interface benefits from a wider bus, and choose the 8-bit-at-60-MHz mode when a narrower interface with a higher clock rate is preferable. The manufacturer datasheet describes both modes as 60 Mbit/s parallel operation. The final choice depends on FPGA timing margins, routing complexity, clock availability, and required interface width.
Does the CY7C68000A-56LFXC support USB 2.0 test modes?
Yes, the CY7C68000A-56LFXC supports USB 2.0 test modes. This capability is explicitly identified in the manufacturer datasheet and is useful in USB compliance, characterization, and production-test environments. Test-mode implementation should follow the datasheet guidance and the applicable USB 2.0 test procedure, including the required device states, data patterns, and instrumentation connections.
What PCB layout practices are important for the CY7C68000A-56LFXC?
The CY7C68000A-56LFXC requires careful high-speed PCB layout because it combines USB differential signaling with a 56-terminal QFN footprint. Keep D+ and D- as a short, tightly coupled pair with continuous ground reference, match the exposed thermal-pad layout to the manufacturer drawing, and place decoupling connections directly to the relevant supply and ground pins. The parallel bus also requires short, impedance-controlled routes to the controller or FPGA.
Is the CY7C68000A-56LFXC suitable for industrial equipment?
The CY7C68000A-56LFXC can be evaluated for industrial USB connectivity because it provides USB 2.0 full-speed operation and a selectable 16-bit or 8-bit parallel interface. However, the listed part is identified as commercial grade, so confirm its specified operating-temperature range against the equipment enclosure. Use an automotive- or industrial-grade variant only when its exact qualification and temperature ratings match the system requirement.
What is the difference between CY7C68000A-56LFXC and CY7C68000-56LFXC?
The principal documented difference is the product revision represented by the A suffix in CY7C68000A-56LFXC versus the earlier CY7C68000-56LFXC naming. Both are identified as Cypress or Infineon MoBL-USB TX2 USB 2.0 UTMI transceivers with 56-pin QFN packaging. Review the manufacturer revision history and compare all pin, electrical, and lifecycle details before treating the earlier designation as a drop-in substitute.
How do I buy the CY7C68000A-56LFXC and request current pricing?
Use the Request a Quote form on this page to request current pricing, stock status, manufacturer packaging, and lead time for the CY7C68000A-56LFXC. The part is listed as a 56-QFN full-speed USB 2.0 transceiver, but commercial conditions can change. Include your required quantity, target package suffix, acceptable date code, and assembly requirements so the quotation can match the intended production build.
What should I check before replacing the CY7C68000A-56LFXC on an existing PCB?
Check package dimensions, terminal numbering, exposed-pad layout, USB differential routing, supply requirements, operating temperature, and interface-mode compatibility before replacing the CY7C68000A-56LFXC. A shared 56-QFN outline is necessary but not sufficient for interchangeability. Compare the candidate against the manufacturer datasheet and confirm that any existing firmware, FPGA constraints, and test-fixture assumptions remain valid.
What can replace the CY7C68000A-56LFXC?
The CY7C68000A-56LTXC is the strongest supported replacement candidate because it is identified as a 480-Mbps USB 2.0 transceiver in the same 56-pin QFN format. The CY7C68000-56LFXC is another same-package family member that may fit older designs. Both candidates require a final pin, electrical, temperature, and lifecycle review; no verified cross-manufacturer drop-in replacement was identified.

Données de référence d'ingénierie pour CY7C68000A-56LFXC — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the CY7C68000A-56LFXC when a design requires a full-speed USB 2.0 physical interface, selectable 16-bit or 8-bit parallel operation, and USB 2.0 test-mode support in a 56-QFN footprint. The 16-bit mode can simplify datapath width and reduce parallel-route count, while the 8-bit mode provides a faster clock for controllers or FPGA logic designed around that timing. Consider the CY7C68000A-56LTXC when its ordering suffix and documented terminal configuration fit the production BOM. The CY7C68000-56LFXC is relevant for designs previously qualified around the earlier family designation, but its revision history must be checked carefully. No cross-manufacturer drop-in replacement was confirmed, so changing manufacturers would require a new footprint and signal-integrity review rather than a simple substitution.

Comparaison avec les alternatives

Paramètre Ce produit CY7C68000A-56LTXC CY7C68000-56LFXC
Package 56-QFN (8 mm x 8 mm) 56-QFN (8 mm x 8 mm) 56-QFN (8 mm x 8 mm)
Brand Infineon Technologies Infineon Technologies Infineon Technologies
USB Specification USB 2.0 USB 2.0 USB 2.0
Maximum USB Data Rate 480 Mbps 480 Mbps 480 Mbps
Architecture MoBL-USB TX2 USB 2.0 UTMI transceiver USB 2.0 transceiver MoBL-USB TX2 USB 2.0 UTMI transceiver

Principaux différenciateurs

  • Configurable parallel-interface organization (vs CY7C68000-56LFXC)
  • USB 2.0 test-mode capability (vs CY7C68000-56LFXC)
  • Compact high-density integration (vs CY7C68000A-56LTXC)

Notes de conception

Use the manufacturer HVQCCN package drawing for the 56-terminal QFN footprint, exposed-pad land, solder-mask opening, and paste pattern. Do not substitute a generic 56-QFN footprint based only on body size. Assign terminals from the datasheet pin-description table, then verify every exposed-pad connection in the schematic and continuity-test the finished board before applying power.

Route USB D+ and D- as a short, tightly coupled differential pair over a continuous ground reference. Avoid stubs, test pads, and plane transitions beneath the pair. Match the pair geometry to the board's controlled-impedance stack-up and keep the USB connector, protection devices, and transceiver in a predictable signal path. The parallel bus should also have short routes and an uninterrupted return path.

Do not treat the 60 MHz parallel clock as a 60-MHz USB bus signal or assume that every 56-QFN USB transceiver has the same terminal assignments. Select the 16-bit-at-30-MHz or 8-bit-at-60-MHz configuration explicitly in the controller or FPGA design, and check clock, data-valid, enable, and reset timing against the manufacturer datasheet.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The part is identified as commercial grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration for the exact ordering suffix.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

CY7C68000A-56LFXC CY7C68000A-56LFXC datasheet CY7C68000A-56LFXC datasheet pdf CY7C68000A-56LFXC pinout CY7C68000A-56LFXC equivalent CY7C68000A-56LFXC replacement CY7C68000A-56LFXC footprint CY7C68000A-56LFXC price Infineon CY7C68000A-56LFXC CY7C68000A-56LFXC USB 2.0 transceiver CY7C68000A-56LFXC 56 QFN CY7C68000A-56LFXC FPGA interface CY7C68000A-56LFXC vs CY7C68000A-56LTXC CY7C68000A-56LFXC schematic CY7C68000A-56LFXC cross reference

Composants & termes associés

Infineon Technologies Cypress Semiconductor CY7C68000A-56LFXC CY7C68000A-56LTXC CY7C68000-56LFXC MoBL-USB TX2 USB 2.0 USB transceiver UTMI transceiver serial and deserializer parallel interface 480 Mbps 60 Mbit/s 16 bits at 30 MHz 8 bits at 60 MHz 56-QFN HVQCCN 8 mm by 8 mm package QFN package family surface-mount package FPGA industrial data acquisition USB test mode embedded USB controller exposed pad
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ