CY7C68000A-56LFXC USB 2.0 Transceiver | Infineon Technologies
部品番号: CY7C68000A-56LFXC ✓ 生産中CY7C68000A-56LFXC 概要
A USB transceiver is an interface semiconductor that converts between serial differential USB signaling and a parallel digital data bus. It belongs to the USB interface controller ecosystem and broader interface IC category, providing the physical-layer path between a host or device controller and an external USB connector. The parallel interface simplifies integration with programmable hardware while retaining compatibility with USB 2.0 full-speed operation.
The CY7C68000A-56LFXC supports USB 2.0 test modes and is identified as a 1/1 full USB 2.0 transceiver. The device can accommodate two parallel-interface configurations: 16 bits at 30 MHz and 8 bits at 60 MHz. This selectable operating arrangement is useful when balancing bus width, clocking requirements, FPGA resource use, and data throughput in USB connectivity designs.
The MoBL-USB TX2 architecture integrates the USB serial transmitter and receiver with a parallel data interface. In one supported configuration, sixteen parallel bits are transferred at 30 MHz; in the other, eight parallel bits are transferred at 60 MHz. Both modes present the same 60 million bit-per-second parallel transfer rate while allowing the system designer to choose between a wider, slower bus and a narrower, faster bus.
Typical uses include USB-to-FPGA gateways, test and measurement systems, industrial data-acquisition equipment, USB peripheral controllers, and embedded USB connectivity platforms. The 56-QFN package supports compact, high-density PCB layouts, but its exposed thermal pad and high-speed interfaces require careful footprint, solder, and return-path design.
For implementation, preserve the differential impedance of the USB D+ and D- connection, provide continuous return paths beneath high-speed traces, and follow the manufacturer pin-description table when assigning every QFN terminal. Use the exposed-pad land pattern and paste geometry specified by the manufacturer rather than substituting a generic 56-QFN footprint.
This product page combines the manufacturer interface capabilities, package information, and verified replacement references with application-specific implementation guidance. It helps engineers distinguish the two parallel operating modes, identify meaningful same-family alternatives, and plan a USB 2.0 transceiver layout before committing a new board to production.
ドロップイン代替品: CY7C68000A-56LFXC — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CY7C68000A-56LFXC (同一形状・フットプリント) — 相違点: USB Specification, Architecture, Maximum USB Data Rate, Package, Package Type.
CY7C68000A-56LTXC
✅ ドロップイン📋 参考代替品(カタログ未掲載)
CY7C68000-56LFXC
✅ ドロップイン価格はお問い合わせください
データシートを見る →CY7C68000A-56LFXC 仕様
| Device Type | 1/1 USB 2.0 transceiver |
| USB Specification | USB 2.0 |
| Maximum USB Data Rate | 480 Mbps |
| Wide Parallel Interface | 16 bits at 30 MHz |
| Narrow Parallel Interface | 8 bits at 60 MHz |
| Parallel Transfer Rate | 60 Mbit/s |
| Test Mode Support | USB 2.0 test modes |
| パッケージ | 56-pin QFN, 8 mm x 8 mm |
| Terminal Count | 56 terminals |
| Package Code | HVQCCN |
| Package Shape | Square |
| 実装スタイル | No-lead surface mount |
| Temperature Grade | Commercial |
| Supply Configuration | Single transceiver |
| Architecture | MoBL-USB TX2 USB 2.0 UTMI transceiver |
| Serializer/Deserializer Support | Yes |
CY7C68000A-56LFXC square ピン配置ガイド
CY7C68000A-56LFXC (square パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: CY7C68000A-56LFXC.
詳細は データシート をご参照ください。
主な用途
CY7C68000A-56LFXC の用途: 6 件s: FPGA USB 2.0 Data Gateway, USB Test and Measurement Equipment, Industrial USB Data Acquisition, Embedded USB Peripheral Controller, USB-to-Parallel Protocol Bridge, USB Protocol Development Platform.
FPGA USB 2.0 Data Gateway
The CY7C68000A-56LFXC fits an FPGA-based USB gateway because the manufacturer supports both a 16-bit interface at 30 MHz and an 8-bit interface at 60 MHz. The selected mode determines how many FPGA I/O resources are committed to the parallel bus and how tightly the internal clocking must be constrained. Its 60 Mbit/s parallel transfer rate supports a practical division of labor between the USB physical interface and user-defined FPGA logic. Preserve a continuous ground reference beneath the USB D+ and D- pair, route the pair as a coupled differential pair, and use the manufacturer QFN land pattern and exposed-pad geometry.
おすすめ
USB Test and Measurement Equipment
The CY7C68000A-56LFXC is appropriate for USB connectivity in test and measurement equipment because it supports USB 2.0 test modes alongside the standard full-speed serial interface. Its parallel bus can be configured as 16 bits at 30 MHz for straightforward data capture or 8 bits at 60 MHz for narrower implementations. Test-mode behavior, serial descriptors, and loopback states should follow the manufacturer datasheet and applicable USB 2.0 procedures. Keep sensitive analog and reference circuitry physically separated from the USB pair, and provide low-impedance supply and ground connections to minimize susceptibility to test-bench noise.
おすすめ
Industrial USB Data Acquisition
The CY7C68000A-56LFXC can serve as the USB physical interface in an industrial data-acquisition controller where a parallel logic connection is preferable to a direct serial processor peripheral. The manufacturer-described 16-bit-at-30-MHz and 8-bit-at-60-MHz modes give the controller designer flexibility to balance register bandwidth against wiring density. The commercial-grade designation requires comparison with the enclosure's temperature range before production release. Maintain continuous ground planes, place bypass capacitors near their assigned device pins, and isolate the USB differential route from high-current switching stages to preserve signal integrity.
おすすめ
Embedded USB Peripheral Controller
The CY7C68000A-56LFXC is suitable for an embedded USB peripheral controller that separates USB physical signaling from an internal parallel bus. At 8 bits and 60 MHz, the interface can connect to faster internal logic, while the 16-bit mode at 30 MHz offers a wider data path that may simplify certain register or datapath implementations. Because both modes have the same stated parallel transfer rate, the selection should follow timing closure, available I/O, and routing constraints. Follow the terminal table exactly and expose the device's exposed-pad thermal connection according to the manufacturer package drawing.
おすすめ
USB-to-Parallel Protocol Bridge
The CY7C68000A-56LFXC can bridge a USB 2.0 full-speed connection to an external parallel subsystem when the destination device expects a synchronous bus. The choice between 16 bits at 30 MHz and 8 bits at 60 MHz provides a meaningful hardware-design choice: wider buses can reduce signal count, while narrower buses can align more closely with high-speed internal logic. Build clocking and data-valid handling around the selected mode in the manufacturer datasheet. Route the parallel nets as short, properly terminated paths and keep the USB pair away from clocks, switching nodes, and other potential aggressors.
おすすめ
USB Protocol Development Platform
The CY7C68000A-56LFXC supports USB protocol development because it combines a full-speed USB 2.0 physical interface with two selectable parallel widths. Developers can use the 16-bit mode to simplify capture logic or the 8-bit mode to explore faster parallel timing, while USB 2.0 test-mode support assists in validation. The 56-QFN package permits compact implementation but leaves little tolerance for an improvised footprint or pad design. Reproduce the manufacturer terminal map and exposed-pad geometry, include test access to D+ and D-, and preserve short return paths beneath the differential pair.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CY7C68000A-56LFXC — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CY7C68000A-56LTXC | CY7C68000-56LFXC |
|---|---|---|---|
| Package | 56-QFN (8 mm x 8 mm) | 56-QFN (8 mm x 8 mm) | 56-QFN (8 mm x 8 mm) |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| USB Specification | USB 2.0 | USB 2.0 | USB 2.0 |
| Maximum USB Data Rate | 480 Mbps | 480 Mbps | 480 Mbps |
| Architecture | MoBL-USB TX2 USB 2.0 UTMI transceiver | USB 2.0 transceiver | MoBL-USB TX2 USB 2.0 UTMI transceiver |
主な差別化要因
- Configurable parallel-interface organization (vs CY7C68000-56LFXC)
- USB 2.0 test-mode capability (vs CY7C68000-56LFXC)
- Compact high-density integration (vs CY7C68000A-56LTXC)
設計ノート
Use the manufacturer HVQCCN package drawing for the 56-terminal QFN footprint, exposed-pad land, solder-mask opening, and paste pattern. Do not substitute a generic 56-QFN footprint based only on body size. Assign terminals from the datasheet pin-description table, then verify every exposed-pad connection in the schematic and continuity-test the finished board before applying power.
Route USB D+ and D- as a short, tightly coupled differential pair over a continuous ground reference. Avoid stubs, test pads, and plane transitions beneath the pair. Match the pair geometry to the board's controlled-impedance stack-up and keep the USB connector, protection devices, and transceiver in a predictable signal path. The parallel bus should also have short routes and an uninterrupted return path.
Do not treat the 60 MHz parallel clock as a 60-MHz USB bus signal or assume that every 56-QFN USB transceiver has the same terminal assignments. Select the 16-bit-at-30-MHz or 8-bit-at-60-MHz configuration explicitly in the controller or FPGA design, and check clock, data-valid, enable, and reset timing against the manufacturer datasheet.
コンプライアンス情報
The part is identified as commercial grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration for the exact ordering suffix.