Maxim Integrated

DG401CY+ Dual 45Ω SPST Analog Switch | Maxim Integrated

Référence : DG401CY+ ✓ Actif
+10 V to +30 V Vdss 500 pA Id 45 ohm Rds(on) 16-SOIC, 0.154 inch body width, 3.90 mm Package
MOQ : 1 |

DG401CY+ Présentation

The Maxim Integrated DG401CY+ is a dual, single-pole single-throw analog switch with a 1:1 circuit configuration, 45 Ω on-resistance, and a 16-SOIC package. It provides 150 ns switching time, 100 ns break-before-make behavior, 500 pA leakage, 15 V supply capability, rail-to-rail signal handling, and TTL/CMOS-compatible control logic. The two independent switch channels make it suitable for routing analog signals in test, measurement, communications, and instrumentation systems.

An analog switch is an integrated semiconductor device that routes an electrical signal between terminals under digital control. Unlike a mechanical relay, it changes state rapidly with low switching delay and limited control power. The DG401CY+ belongs to the analog-switch hierarchy within interface ICs and is commonly used when a compact, logic-controlled signal path is required. Each SPST channel connects one signal terminal to one common terminal, providing straightforward routing for multiplexed or configurable analog front ends.

The device’s 45 Ω on-resistance is suitable for many low- and moderate-impedance signal paths. The listed 150 ns switching time supports fast control-loop or acquisition sequencing, while the 100 ns break-before-make interval prevents the two sides of a switched connection from momentarily shorting together. Rail-to-rail operation allows signals to approach the supply limits, and TTL/CMOS-compatible logic simplifies connection to common digital controllers.

Power capability is specified for single-supply operation from +10 V to +30 V and bipolar-supply operation from ±4.5 V to ±20 V. Low power consumption is listed at 35 µW maximum. These operating ranges give designers flexibility for laboratory instrumentation, industrial control systems, signal-conditioning modules, and communication equipment while preserving compatibility with both positive-only and split-supply architectures.

Typical applications include multimeter input routing, automated test equipment, programmable signal-path modules, analog measurement front ends, sample-and-hold isolation, and communication-channel selection. Independent control inputs allow the two channels to be switched independently when a system needs one signal route at a time or coordinated routing between two external nodes.

Layout and signal integrity require close attention because the on-resistance, leakage current, and switching transients can affect high-impedance or precision circuits. Keep analog traces short, use a solid ground reference, and avoid routing sensitive signals directly beneath control inputs. Confirm the complete pin configuration and operating limits against the manufacturer datasheet before finalizing the PCB footprint.

This page consolidates the switch configuration, electrical characteristics, operating ranges, application guidance, and design cautions into an engineering-focused reference. It also distinguishes true pin-to-pin replacements from merely similar switch products, helping designers avoid substitutions that differ in logic polarity, supply range, pinout, or switching behavior.

Alternatives de remplacement direct pour DG401CY+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Aucune alternative de remplacement direct disponible pour ce produit.

Demander des alternatives

DG401CY+ Valeurs maximales et caractéristiques électriques

Number of Switches 2
Switch Configuration 1:1
Switch Type Dual SPST
On-Resistance 45 ohm
Maximum Switching Time 150 ns
Break-Before-Make Time 100 ns
Off Leakage Current 500 pA
Single-Supply Operating Voltage +10 V to +30 V
Bipolar-Supply Operating Voltage +/-4.5 V to +/-20 V
Maximum Power Consumption 35 uW
Signal Handling Rail-to-rail
Logic Compatibility TTL/CMOS compatible
Boîtier 16-SOIC, 0.154 inch body width, 3.90 mm
Nombre de broches 16 pins
Type de montage Surface mount

Guide de configuration des broches du DG401CY+ 16-soic, 0.154 inch body width, 3.90 mm

Configuration des broches du DG401CY+ (boîtier 16-soic, 0.154 inch body width, 3.90 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 16-soic, 0.154 inch body width, 3.90 mm pour le DG401CY+

Aucune donnée de brochage détaillée disponible pour DG401CY+.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

DG401CY+ convient pour 6 applications: Multimeter Input Routing, Automated Test Equipment, Programmable Signal Conditioning, Industrial Communication Interfaces, Sample-and-Hold Isolation, Laboratory Instrument Interconnect.

🔧

Multimeter Input Routing

The DG401CY+ fits a programmable multimeter input module because its two SPST channels can route measurement leads under digital control while preserving a compact 16-SOIC footprint. The 150 ns switching time allows rapid range or source selection without mechanical-relay delay, and the 100 ns break-before-make interval helps prevent unintended overlap during transitions. For high-impedance measurements, evaluate the 45 Ω on-resistance as a source of attenuation and the 500 pA leakage as an error contribution. Place switch traces close to the input network, maintain a low-impedance reference plane, and keep relay or protection components away from sensitive nodes to prevent leakage and switching transients from dominating the measurement.

🏭

Automated Test Equipment

The DG401CY+ is appropriate for automated test equipment that needs to connect DUT pins, test resources, or external fixtures through a fast, compact switching network. Its 150 ns switching performance supports short measurement dwell times, while the 1:1 topology provides uncomplicated point-to-point routing for two independent channels. The 16-SOIC package reduces PCB area compared with discrete relays, but designers should include protection against transient voltages, verify the 500 pA leakage requirement for high-impedance measurements, and assess whether 45 Ω is acceptable for the instrument input. A defined ground-return layout and controlled digital control timing are essential for repeatable fixture behavior.

📡

Programmable Signal Conditioning

The DG401CY+ can be used in programmable signal-conditioning modules to select between external test signals, sensor outputs, or reference paths. Its rail-to-rail signal handling supports a broad usable range within the selected supply architecture, and TTL/CMOS-compatible control simplifies operation from a microcontroller or digital controller. The dual independent configuration allows a board to implement two routing decisions without adding two separate single-switch packages. Because the listed on-resistance is 45 Ω, use buffer stages for substantially lower source impedance when signal amplitude and phase accuracy matter. Confirm leakage, switching transients, and control thresholds against the manufacturer datasheet before assigning sensitive precision nodes.

🌐

Industrial Communication Interfaces

The DG401CY+ fits low-rate industrial communication and control interfaces that need economical, fast analog routing in a small package. The 150 ns transition time is useful for direction or channel-control functions, while 100 ns break-before-make behavior reduces the chance of an undesirable momentary connection between switched nodes. TTL/CMOS-compatible inputs simplify integration with digital control logic, and operation from +10 V to +30 V or ±4.5 V to ±20 V supports both single-rail and split-rail equipment architectures. Engineers should still account for the 45 Ω series resistance, use low-inductance routing and a continuous ground plane, and place any protection components where their leakage and capacitance do not impair the selected signal path.

📺

Sample-and-Hold Isolation

The DG401CY+ can isolate a sampling node by briefly disconnecting it from a source during acquisition, conversion, or readout. Its 150 ns switching time supports short transition intervals, and the 100 ns break-before-make specification helps ensure that the previous path is released before another path is established. The 500 pA leakage rating is advantageous around high-impedance hold capacitors because leakage from the switch can alter the stored voltage over time. In practice, capacitor dielectric leakage, dielectric absorption, and board contamination can dominate the error budget, so use a low-leakage capacitor and clean PCB practices. Keep the switch and hold capacitor physically close to minimize parasitic capacitance and susceptibility to control-edge coupling.

🧪

Laboratory Instrument Interconnect

The DG401CY+ is useful in laboratory instruments that connect precision or high-bandwidth-adjacent sources through a compact routing matrix. The device's small 16-SOIC footprint and fast control response help create repeatable channel selection without relying on slower mechanical relays. Its ±4.5 V to ±20 V bipolar operating range suits split-supply analog sections, while +10 V to +30 V single-supply operation accommodates positive-rail systems. Signal integrity depends on layout: use short traces, a solid ground plane, and deliberate control routing that avoids capacitively coupling switching edges into sensitive inputs. Verify the actual bandwidth response and on-resistance matching from the manufacturer datasheet for each operating point.

Récapitulatif des produits recommandés

DG401CY+ Maxim Integrated Utilisé dans : Multimeter Input Routing, Automated Test Equipment, Programmable Signal Conditioning, Industrial Communication Interfaces, Sample-and-Hold Isolation, Laboratory Instrument Interconnect DG401CY Base dual analog-switch family designation Utilisé dans : Multimeter Input Routing, Automated Test Equipment, Programmable Signal Conditioning, Industrial Communication Interfaces, Sample-and-Hold Isolation, Laboratory Instrument Interconnect
What is the DG401CY+?
The DG401CY+ is a dual SPST analog switch from Maxim Integrated with a 1:1 configuration and 45 Ω on-resistance in a 16-SOIC package. According to the manufacturer datasheet, it provides 150 ns switching time, 100 ns break-before-make behavior, and TTL/CMOS-compatible logic. It is designed for rapid routing of analog signals in instrumentation, test equipment, industrial control, and communication systems.
How many switches and circuits does the DG401CY+ contain?
The DG401CY+ contains two independent SPST switches, and each channel has a 1:1 circuit configuration. The manufacturer datasheet identifies the device as a dual high-speed analog switch, while distributor product records describe it as a 2-circuit 1:1 device in a 16-SOIC package. This makes it suitable for routing two controlled analog paths without using a larger multiplexer.
What is the on-resistance of the DG401CY+?
The DG401CY+ has a listed on-resistance of 45 Ω. According to the manufacturer datasheet, the DG401 family also provides low rDS(ON), specified at 30 Ω maximum in the indexed datasheet description. The 45 Ω figure corresponds to the individual DG401CY+ product listing, so designers should use the exact value and test conditions from the DG401CY datasheet for signal-loss calculations.
What is the switching speed of the DG401CY+?
The DG401CY+ switches in 150 ns and has a 100 ns break-before-make interval. The manufacturer datasheet and component listings identify both values for this high-speed analog switch. The 150 ns figure supports rapid routing, while the 100 ns dead time prevents the two connected nodes from being shorted during complementary switching transitions.
Is the DG401CY+ compatible with TTL and CMOS control signals?
The DG401CY+ has TTL/CMOS-compatible logic inputs, according to the manufacturer datasheet. This allows its control signals to be driven by common digital logic families without an intermediate level-conversion stage. The exact input thresholds and permissible supply combinations should still be checked against the manufacturer datasheet when designing around unusual voltage levels or nonstandard control timing.
What supply voltages can the DG401CY+ operate from?
The DG401CY+ supports single-supply operation from +10 V to +30 V and bipolar operation from ±4.5 V to ±20 V. The manufacturer datasheet states those ranges explicitly. Single-supply operation suits systems with one positive rail, while bipolar operation supports signal paths that include signals around ground and can provide additional signal-swing margin.
What is the leakage current of the DG401CY+?
The listed off-state leakage current for the DG401CY+ is 500 pA. According to the component data, this low leakage supports high-impedance measurement circuits by limiting unintended current through the open switch. Actual error contribution depends on source impedance, temperature, supply voltage, and the surrounding measurement front end, so verify the worst-case conditions in the manufacturer datasheet.
Where can I download the DG401CY+ datasheet PDF?
The DG401CY datasheet PDF can be downloaded from the indexed manufacturer-document mirror at https://pdf.digi-electronics.com/pdf/1471/DG401CY-datasheet.pdf. It contains the device description, electrical characteristics, operating ranges, application information, and package details. Use the pin-description and truth-table sections when assigning control inputs and verifying the 16-SOIC footprint.
Where can I find the DG401CY+ pinout?
The DG401CY+ pinout is documented in the DG401CY manufacturer datasheet, beginning with the pin-description diagram and accompanying table. The component is a 16-SOIC device, so the schematic symbol and PCB footprint should be checked against those 16 numbered terminals. Do not infer terminal functions from generic SPST symbols because enable polarity and common-terminal assignments must follow the exact datasheet drawing.
What is the best drop-in replacement for the DG401CY+?
The best drop-in replacement must use the same 16-SOIC footprint and preserve the DG401CY+ pin functions, supply limits, control logic, and approximately 45 Ω switching characteristics. No confirmed pin-compatible replacement is established by the available cross-reference results, so request a quote with the target MPN and describe the required configuration. This avoids treating a similar dual analog switch as a safe drop-in substitute.
What can replace the DG401CY+?
A replacement for the DG401CY+ should be a dual, 1:1 SPST switch in a 16-SOIC package with compatible control polarity, break-before-make timing, and supply ratings. No alternative in the cross-reference results is confirmed as pin-to-pin compatible. During replacement review, compare the complete pin description, on-resistance, leakage current, switching time, and operating ranges rather than relying only on the package type.
Is DG401CY+ suitable for high-impedance instrumentation?
The DG401CY+ can be suitable for high-impedance instrumentation when its 500 pA leakage rating is adequate for the required measurement accuracy. Its 45 Ω on-resistance may be too high for source impedances where significant attenuation occurs, so calculate the divider formed by the switch resistance and input impedance. The 150 ns switching speed also makes it useful for rapid measurement-path selection.
Is the DG401CY+ an active or obsolete part?
The DG401CY+ is listed as active in the component index, with an inventory record showing 21,600 units in stock. Current supply conditions can change, so use the Request a Quote form on this page to obtain present stock, minimum order quantity, and lead time for the exact 16-SOIC ordering code.
Where can I buy DG401CY+ and check its lead time?
Use the Request a Quote form on this page to request current DG401CY+ pricing, stock, minimum order quantity, and lead time. The component is a 16-SOIC dual SPST analog switch, and the exact ordering suffix matters when a manufacturer offers multiple package or qualification options. The quote form avoids publishing a transient stock count or a stale lead-time estimate.
What is the price of the DG401CY+?
The current DG401CY+ price is best requested through the Request a Quote form on this page because quotation terms depend on quantity and current channel conditions. The component index identifies the device as active, while the product listings include both 16-SOIC inventory and quote-based sourcing records. Submit the required quantity to receive an exact quotation.
Is the DG401CY+ RoHS compliant?
The RoHS status of the DG401CY+ is not stated in the indexed technical material and therefore remains unconfirmed. Use the manufacturer datasheet or product documentation for the authoritative compliance declaration, and request the applicable material-compliance statement through the Request a Quote form. Do not assume regulatory status solely from the manufacturer or package family.

Données de référence d'ingénierie pour DG401CY+ — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the DG401CY+ when the design needs two independent 1:1 SPST routes, a 16-SOIC footprint, and switching transitions completed in 150 ns with 100 ns break-before-make behavior. It is especially useful for laboratory instruments, automated test fixtures, programmable signal conditioning, and communication modules that benefit from fast electronic routing without a mechanical relay. The listed 45 Ω on-resistance makes it most appropriate for moderate-impedance paths; add a buffer when lower source impedance or higher precision is required. The 500 pA leakage is useful around high-impedance circuits, although capacitor and PCB leakage must also be controlled. Because no confirmed pin-to-pin replacement was established, do not substitute based only on dual-SPST and SOIC-16 similarity. Require an exact pinout, control-polarity, supply-range, timing, leakage, and impedance review for any proposed replacement.

Comparaison avec les alternatives

Paramètre Ce produit
Package 16-SOIC, 0.154 inch body width, 3.90 mm
Brand Maxim Integrated
Number of Switches 2
Switch Configuration 1:1
Switch Type Dual SPST
On-Resistance 45 ohm
Switching Time 150 ns
Break-Before-Make Time 100 ns
Off Leakage Current 500 pA
Single-Supply Range +10 V to +30 V
Bipolar-Supply Range +/-4.5 V to +/-20 V
Maximum Power Consumption 35 uW
Logic Compatibility TTL/CMOS compatible

Principaux différenciateurs

  • Fast dual-channel analog routing in one package (vs No confirmed drop-in alternative)
  • Broad single-rail operating capability (vs No confirmed drop-in alternative)
  • Low off-state leakage for sensitive routing (vs No confirmed drop-in alternative)
  • Logic-compatible control without level translation (vs No confirmed drop-in alternative)

Notes de conception

Treat the 45 Ω on-resistance as a real series element in the selected signal path. For a resistive source network, calculate the resulting attenuation before choosing buffer stages; a high-impedance receiver may see little voltage loss, while a low-impedance load can experience substantial division. Keep input and output routing short, use a continuous ground plane, and place the switch close to the signal source when switch resistance or parasitic capacitance materially affects the design.

Use the manufacturer pin-description drawing to assign the 16-SOIC terminals and verify the PCB land pattern by dimensions rather than by package-family assumption. Keep the two switched paths physically separate where possible, route control inputs away from sensitive analog nodes, and provide a low-impedance return path beneath the device. Short control traces also reduce timing skew between the two channels and limit switching energy coupled into nearby measurement circuitry.

Do not interpret the 1:1 circuit description as proof that any SPST switch is interchangeable. A valid replacement must preserve terminal assignments, control polarity, supply range, break-before-make behavior, and the 45 Ω-class switching impedance. Also distinguish the individual DG401CY+ listing from family-level DG401 ratings: use the exact ordering code and its datasheet limits when checking the 500 pA leakage, 150 ns switching time, and 100 ns break-before-make specification.

Select the supply architecture from the rated operating regions: +10 V to +30 V for single-supply use or ±4.5 V to ±20 V for bipolar use. Decouple the supply pins close to the package and provide a clean return connection. The listed maximum power consumption is 35 µW, but total system dissipation must also include logic-interface power and any external protection components because those values may not be included in the device-only consumption figure.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The indexed technical material does not state the regulatory compliance status of the DG401CY+. Obtain the current manufacturer compliance documentation before releasing an automotive or restricted-substance-controlled design.

Recherches associées

DG401CY+ datasheet DG401CY+ pinout DG401CY+ datasheet pdf DG401CY+ specifications DG401CY+ 16-SOIC DG401CY+ equivalent DG401CY+ replacement DG401CY+ cross reference DG401CY+ price DG401CY+ stock Maxim Integrated DG401CY+ DG401CY+ application circuit

Composants & termes associés

Maxim Integrated DG401CY+ DG401CY DG401 dual SPST analog switch analog switch interface IC semiconductor single-pole single-throw 1:1 switch configuration on-resistance break-before-make switching time off leakage current rail-to-rail signal handling TTL CMOS 16-SOIC SOIC package family surface-mount package single-supply operation bipolar-supply operation automated test equipment programmable signal conditioning
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ