DG401CY+ Dual 45Ω SPST Analog Switch | Maxim Integrated
N.º da peça: DG401CY+ ✓ AtivoDG401CY+ Visão geral
An analog switch is an integrated semiconductor device that routes an electrical signal between terminals under digital control. Unlike a mechanical relay, it changes state rapidly with low switching delay and limited control power. The DG401CY+ belongs to the analog-switch hierarchy within interface ICs and is commonly used when a compact, logic-controlled signal path is required. Each SPST channel connects one signal terminal to one common terminal, providing straightforward routing for multiplexed or configurable analog front ends.
The device’s 45 Ω on-resistance is suitable for many low- and moderate-impedance signal paths. The listed 150 ns switching time supports fast control-loop or acquisition sequencing, while the 100 ns break-before-make interval prevents the two sides of a switched connection from momentarily shorting together. Rail-to-rail operation allows signals to approach the supply limits, and TTL/CMOS-compatible logic simplifies connection to common digital controllers.
Power capability is specified for single-supply operation from +10 V to +30 V and bipolar-supply operation from ±4.5 V to ±20 V. Low power consumption is listed at 35 µW maximum. These operating ranges give designers flexibility for laboratory instrumentation, industrial control systems, signal-conditioning modules, and communication equipment while preserving compatibility with both positive-only and split-supply architectures.
Typical applications include multimeter input routing, automated test equipment, programmable signal-path modules, analog measurement front ends, sample-and-hold isolation, and communication-channel selection. Independent control inputs allow the two channels to be switched independently when a system needs one signal route at a time or coordinated routing between two external nodes.
Layout and signal integrity require close attention because the on-resistance, leakage current, and switching transients can affect high-impedance or precision circuits. Keep analog traces short, use a solid ground reference, and avoid routing sensitive signals directly beneath control inputs. Confirm the complete pin configuration and operating limits against the manufacturer datasheet before finalizing the PCB footprint.
This page consolidates the switch configuration, electrical characteristics, operating ranges, application guidance, and design cautions into an engineering-focused reference. It also distinguishes true pin-to-pin replacements from merely similar switch products, helping designers avoid substitutions that differ in logic polarity, supply range, pinout, or switching behavior.
Alternativas drop-in para DG401CY+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasDG401CY+ Classificações máximas e características elétricas
| Number of Switches | 2 |
| Switch Configuration | 1:1 |
| Switch Type | Dual SPST |
| On-Resistance | 45 ohm |
| Maximum Switching Time | 150 ns |
| Break-Before-Make Time | 100 ns |
| Off Leakage Current | 500 pA |
| Single-Supply Operating Voltage | +10 V to +30 V |
| Bipolar-Supply Operating Voltage | +/-4.5 V to +/-20 V |
| Maximum Power Consumption | 35 uW |
| Signal Handling | Rail-to-rail |
| Logic Compatibility | TTL/CMOS compatible |
| Encapsulamento | 16-SOIC, 0.154 inch body width, 3.90 mm |
| Contagem de pinos | 16 pins |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do DG401CY+ 16-soic, 0.154 inch body width, 3.90 mm
Configuração de pinos para DG401CY+ (pacote 16-soic, 0.154 inch body width, 3.90 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para DG401CY+.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
DG401CY+ é adequado para 6 aplicaçãos: Multimeter Input Routing, Automated Test Equipment, Programmable Signal Conditioning, Industrial Communication Interfaces, Sample-and-Hold Isolation, Laboratory Instrument Interconnect.
Multimeter Input Routing
The DG401CY+ fits a programmable multimeter input module because its two SPST channels can route measurement leads under digital control while preserving a compact 16-SOIC footprint. The 150 ns switching time allows rapid range or source selection without mechanical-relay delay, and the 100 ns break-before-make interval helps prevent unintended overlap during transitions. For high-impedance measurements, evaluate the 45 Ω on-resistance as a source of attenuation and the 500 pA leakage as an error contribution. Place switch traces close to the input network, maintain a low-impedance reference plane, and keep relay or protection components away from sensitive nodes to prevent leakage and switching transients from dominating the measurement.
Recomendado
Automated Test Equipment
The DG401CY+ is appropriate for automated test equipment that needs to connect DUT pins, test resources, or external fixtures through a fast, compact switching network. Its 150 ns switching performance supports short measurement dwell times, while the 1:1 topology provides uncomplicated point-to-point routing for two independent channels. The 16-SOIC package reduces PCB area compared with discrete relays, but designers should include protection against transient voltages, verify the 500 pA leakage requirement for high-impedance measurements, and assess whether 45 Ω is acceptable for the instrument input. A defined ground-return layout and controlled digital control timing are essential for repeatable fixture behavior.
Recomendado
Programmable Signal Conditioning
The DG401CY+ can be used in programmable signal-conditioning modules to select between external test signals, sensor outputs, or reference paths. Its rail-to-rail signal handling supports a broad usable range within the selected supply architecture, and TTL/CMOS-compatible control simplifies operation from a microcontroller or digital controller. The dual independent configuration allows a board to implement two routing decisions without adding two separate single-switch packages. Because the listed on-resistance is 45 Ω, use buffer stages for substantially lower source impedance when signal amplitude and phase accuracy matter. Confirm leakage, switching transients, and control thresholds against the manufacturer datasheet before assigning sensitive precision nodes.
Recomendado
Industrial Communication Interfaces
The DG401CY+ fits low-rate industrial communication and control interfaces that need economical, fast analog routing in a small package. The 150 ns transition time is useful for direction or channel-control functions, while 100 ns break-before-make behavior reduces the chance of an undesirable momentary connection between switched nodes. TTL/CMOS-compatible inputs simplify integration with digital control logic, and operation from +10 V to +30 V or ±4.5 V to ±20 V supports both single-rail and split-rail equipment architectures. Engineers should still account for the 45 Ω series resistance, use low-inductance routing and a continuous ground plane, and place any protection components where their leakage and capacitance do not impair the selected signal path.
Recomendado
Sample-and-Hold Isolation
The DG401CY+ can isolate a sampling node by briefly disconnecting it from a source during acquisition, conversion, or readout. Its 150 ns switching time supports short transition intervals, and the 100 ns break-before-make specification helps ensure that the previous path is released before another path is established. The 500 pA leakage rating is advantageous around high-impedance hold capacitors because leakage from the switch can alter the stored voltage over time. In practice, capacitor dielectric leakage, dielectric absorption, and board contamination can dominate the error budget, so use a low-leakage capacitor and clean PCB practices. Keep the switch and hold capacitor physically close to minimize parasitic capacitance and susceptibility to control-edge coupling.
Recomendado
Laboratory Instrument Interconnect
The DG401CY+ is useful in laboratory instruments that connect precision or high-bandwidth-adjacent sources through a compact routing matrix. The device's small 16-SOIC footprint and fast control response help create repeatable channel selection without relying on slower mechanical relays. Its ±4.5 V to ±20 V bipolar operating range suits split-supply analog sections, while +10 V to +30 V single-supply operation accommodates positive-rail systems. Signal integrity depends on layout: use short traces, a solid ground plane, and deliberate control routing that avoids capacitively coupling switching edges into sensitive inputs. Verify the actual bandwidth response and on-resistance matching from the manufacturer datasheet for each operating point.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para DG401CY+ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Package | 16-SOIC, 0.154 inch body width, 3.90 mm |
| Brand | Maxim Integrated |
| Number of Switches | 2 |
| Switch Configuration | 1:1 |
| Switch Type | Dual SPST |
| On-Resistance | 45 ohm |
| Switching Time | 150 ns |
| Break-Before-Make Time | 100 ns |
| Off Leakage Current | 500 pA |
| Single-Supply Range | +10 V to +30 V |
| Bipolar-Supply Range | +/-4.5 V to +/-20 V |
| Maximum Power Consumption | 35 uW |
| Logic Compatibility | TTL/CMOS compatible |
Principais diferenciais
- Fast dual-channel analog routing in one package (vs No confirmed drop-in alternative)
- Broad single-rail operating capability (vs No confirmed drop-in alternative)
- Low off-state leakage for sensitive routing (vs No confirmed drop-in alternative)
- Logic-compatible control without level translation (vs No confirmed drop-in alternative)
Notas de projeto
Treat the 45 Ω on-resistance as a real series element in the selected signal path. For a resistive source network, calculate the resulting attenuation before choosing buffer stages; a high-impedance receiver may see little voltage loss, while a low-impedance load can experience substantial division. Keep input and output routing short, use a continuous ground plane, and place the switch close to the signal source when switch resistance or parasitic capacitance materially affects the design.
Use the manufacturer pin-description drawing to assign the 16-SOIC terminals and verify the PCB land pattern by dimensions rather than by package-family assumption. Keep the two switched paths physically separate where possible, route control inputs away from sensitive analog nodes, and provide a low-impedance return path beneath the device. Short control traces also reduce timing skew between the two channels and limit switching energy coupled into nearby measurement circuitry.
Do not interpret the 1:1 circuit description as proof that any SPST switch is interchangeable. A valid replacement must preserve terminal assignments, control polarity, supply range, break-before-make behavior, and the 45 Ω-class switching impedance. Also distinguish the individual DG401CY+ listing from family-level DG401 ratings: use the exact ordering code and its datasheet limits when checking the 500 pA leakage, 150 ns switching time, and 100 ns break-before-make specification.
Select the supply architecture from the rated operating regions: +10 V to +30 V for single-supply use or ±4.5 V to ±20 V for bipolar use. Decouple the supply pins close to the package and provide a clean return connection. The listed maximum power consumption is 35 µW, but total system dissipation must also include logic-interface power and any external protection components because those values may not be included in the device-only consumption figure.
Informações de conformidade
The indexed technical material does not state the regulatory compliance status of the DG401CY+. Obtain the current manufacturer compliance documentation before releasing an automotive or restricted-substance-controlled design.