DG411AK - Quad SPST 30 Ohm Analog Switch | Maxim Integrated
Référence : DG411AK ✓ ActifDG411AK Présentation
An analog switch is a semiconductor interface that connects or disconnects signal paths under digital control. The DG411AK belongs to the analog switch hierarchy, where each of its four single-pole, single-throw channels independently routes one signal. This makes the device useful where several precision or instrumentation signals must be selected, isolated, sampled, or connected to a common measurement chain. Unlike a mechanical relay, it changes state electronically without moving contacts.
Key characteristics include four independent SPST switches, 1:1 signal routing, 30-ohm on resistance, on-resistance matching to 3 ohms maximum, and guaranteed on-resistance flatness of 4 ohms maximum across the signal range. The matched resistance improves channel-to-channel consistency, which is important when several switches contribute to the same measurement path. TTL- and CMOS-compatible inputs simplify connection to older logic systems as well as modern control circuitry.
The DG411AK is specified as a military-grade part, and the A suffix identifies the package and temperature treatment associated with the DG411 family. Its 16-pin CERDIP construction is intended for through-hole PCB assembly rather than surface-mount production. Because the switches operate independently, one control signal can be asserted without changing the state of the other three channels, allowing partial signal-path isolation.
Typical uses include precision test and measurement systems, data-acquisition front ends, analog instrumentation, signal-routing matrices, and military or aerospace electronic assemblies. In a measurement system, the four channels can route different sensor or source signals into a common amplifier or converter. The matched on-resistance is especially useful when channel-dependent insertion error must remain small.
PCB design should preserve the pin arrangement defined by the manufacturer datasheet, provide adequate clearance around adjacent high-voltage or low-level signal paths, and route control traces away from sensitive analog nets. Because this is a through-hole military-temperature component, designers should also account for lead soldering, cleaning residue, vibration, and thermal cycling during system qualification. The 30-ohm resistance is appropriate for moderate-impedance instrumentation but may require a lower-resistance switch in high-bandwidth or high-precision applications.
This product page organizes the DG411AK electrical characteristics, package information, commercial sourcing workflow, genuine drop-in alternatives, and application-oriented design guidance for engineers evaluating or replacing this quad SPST analog switch.
Alternatives de remplacement direct pour DG411AK — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DG411AK (même facteur de forme et même empreinte) — différant par Mounting Type, Number of Switches, On-Resistance Flatness, Package.
DG411AK/883B
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DG411DJZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DG411DYZ
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DG411AK Valeurs maximales et caractéristiques électriques
| Number of Switches | 4 |
| Switch Configuration | 4 x SPST |
| Signal-to-Channel Ratio | 1:1 |
| On Resistance | 30 ohm |
| On-Resistance Matching | 3 ohm maximum |
| On-Resistance Flatness | 4 ohm maximum across the signal range |
| Number of Terminals | 16 |
| Boîtier | 16-pin CERDIP |
| Package Code | DIP |
| Package Shape | Rectangular |
| Type de montage | Through hole |
| Surface Mount | No |
| Temperature Grade | Military |
| Digital Input Compatibility | TTL and CMOS compatible |
| Technology | Monolithic CMOS |
Guide de configuration des broches du DG411AK rectangular
Configuration des broches du DG411AK (boîtier rectangular). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DG411AK.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DG411AK convient pour 6 applications: Precision Data-Acquisition Front Ends, Military Test Equipment, Analog Instrumentation Signal Routing, Sensor Signal Multiplexing, Automated Test-System Routing, Aerospace Signal-Selection Networks.
Precision Data-Acquisition Front Ends
The DG411AK fits data-acquisition front ends that must route several sensor or test signals into a shared amplifier or converter. Four independent SPST channels provide 1:1 paths, while the family's 3-ohm maximum on-resistance matching helps limit channel-to-channel insertion differences. The 30-ohm on resistance is suitable for moderate-impedance sources but should be compared with the source impedance and acquisition accuracy budget. With the 16-pin through-hole CERDIP package, the DG411AK also supports rugged instrument assemblies where leaded parts and straightforward socket replacement are preferred.
Recommandé
Military Test Equipment
The DG411AK is appropriate for military test equipment requiring four independently controlled signal paths in a through-hole package. Its military temperature grade and monolithic CMOS implementation fit controlled instrumentation environments where switching consistency matters. The 30-ohm resistance should be included in the gain and attenuation calculation for each routed channel, and the 3-ohm maximum matching specification can be used when defining allowable channel error. Verify program-specific qualification, traceability, and test documentation before incorporating the part into a qualified military configuration.
Recommandé
Analog Instrumentation Signal Routing
The DG411AK can route four independent analog signals in precision instruments where relay-size switching is undesirable and electronic control is preferred. Each 1:1 SPST channel can connect one source to a measurement amplifier without mechanically disturbing the signal path. The 30-ohm on resistance adds series impedance, so source buffering may be needed for high-impedance sensors or high-gain stages. The 16-pin CERDIP package makes the part straightforward to route on through-hole instrument boards and easy to replace during maintenance.
Recommandé
Sensor Signal Multiplexing
The DG411AK can independently connect up to four sensor signals into a common analog-processing chain. The SPST architecture provides isolation when a channel is turned off, while the matched on-resistance helps maintain consistent behavior among channels. For low-level sensors, the switch's 30-ohm contribution may be small relative to high source impedance, but it can become significant with low-impedance sensors. The design should also account for off leakage, switching transients, and the control-signal timing required by the surrounding ADC or instrumentation amplifier.
Recommandé
Automated Test-System Routing
The DG411AK supports automated test systems that route excitation, reference, or return signals among several circuit points. Four independently controlled SPST channels allow a controller to establish different test configurations without changing unrelated paths. Its 30-ohm resistance must be included when calculating signal attenuation and impedance interactions, while the 3-ohm matching limit helps predict channel-to-channel test variation. The leaded CERDIP construction is useful in long-life equipment where serviceability and stable through-hole assembly are priorities.
Recommandé
Aerospace Signal-Selection Networks
The DG411AK can be used in aerospace signal-selection networks where four channels must be routed under digital control and the assembly uses military-grade, through-hole components. The ceramic DIP package offers a mechanically robust assembly option, while monolithic CMOS switching provides compact control and consistent channel behavior. Engineers should verify the exact environmental limits, failure-mode requirements, and qualification obligations for the intended aircraft or space program. On-resistance variation, leakage, and control thresholds must remain within the worst-case analysis for the selected signal bandwidth and loading.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DG411AK — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DG411AK/883B | DG411DJZ | DG411DYZ |
|---|---|---|---|---|
| Package | 16-pin CERDIP | 16-CDIP | CDIP-16 | CDIP-16 |
| Brand | Maxim Integrated | Analog Devices | Renesas Electronics | Renesas Electronics |
| Number of Switches | 4 | 4 | 4 | 4 |
| Switch Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Signal-to-Channel Ratio | 1:1 | 1:1 | 1:1 | 1:1 |
| Mounting Style | Through hole | Through hole | Through hole | Through hole |
Principaux différenciateurs
- Four independently controlled SPST channels in a 16-pin through-hole package (vs DG411AK/883B)
- Documented 30-ohm on-resistance for the exact DG411AK listing (vs DG411DYZ)
- Family-level resistance matching and flatness (vs DG411DJZ)
Notes de conception
Include the 30-ohm on resistance in the complete signal-path calculation. Estimated insertion loss for a simple resistive divider is PLOAD divided by PLOAD plus 30 ohm; for example, a 1-kohm load produces an estimated loss of about 0.13 dB. Add switch leakage, capacitor effects, and amplifier input impedance when evaluating precision measurement accuracy. Use a lower-resistance switch if the calculated error exceeds the measurement budget.
Use the manufacturer package drawing and pin-description table when creating the 16-pin footprint. Confirm ceramic-DIP lead spacing, row geometry, and whether a center key or other package feature affects assembly. Keep analog switch traces short, provide a solid ground plane, and place the device close to the source and destination networks to minimize capacitive pickup and parasitic inductance.
Do not infer control polarity or switch-terminal orientation from the four-channel architecture. Use the exact DG411AK datasheet pinout to distinguish control inputs, common terminals, and switched terminals. Also avoid assuming that every DG411 suffix has the same package or qualification treatment; the AK, /883B, DJZ, and DYZ ordering designations must be checked against the PCB and procurement requirements.
Route digital control traces away from sensitive analog paths, especially when a control edge can couple a transient into a high-gain measurement node. Provide a low-impedance return path beneath digital routes, use a single ground strategy, and avoid long switch-node stubs. If the switched signal has high bandwidth or high amplitude, evaluate edge rate, off-isolation, and charge injection at the actual control-driver impedance.
Informations de conformité
The DG411AK is listed as a military-grade analog switch, but no specific RoHS, REACH, halogen-free, or conflict-minerals declaration is stated in the manufacturer page information.