Analog Devices

DG418CJ+ - 35 Ohm SPST Analog Switch | Analog Devices

Référence : DG418CJ+ ✓ Actif
35 ohm Rds(on) 8-pin PDIP Package
MOQ : 1 |

DG418CJ+ Présentation

Analog Devices DG418CJ+ is a precision CMOS analog switch with a 35 ohm maximum on-resistance, configured as a single SPST circuit in an 8-pin PDIP package. The normally open architecture provides a high-impedance off state between the switched terminals, making the device useful when signal routing, isolation, sampling, and test-fixture control are required. The manufacturer identifies the DG418 family as a production product designed for improved switching consistency and low leakage over temperature.

An analog switch is an interface integrated circuit that connects or disconnects an analog signal path under digital control. Within the semiconductor hierarchy, the DG418CJ+ is an analog switch, a member of the multiplexer and demultiplexer family, and an interface IC used between sensors, measurement circuits, converters, and digital control logic. Unlike a mechanical relay, it can switch without moving physical contacts and can therefore support compact, repeatable signal control.

Key characteristics include a maximum on-resistance of 35 ohms, SPST switching, normally open operation, and an 8-pin PDIP package. The on-resistance specification is important because series resistance can produce signal attenuation and voltage-dependent error in divider networks. The normally open state also provides a useful default: the switched path remains disconnected until the control input asserts the switch. Additional electrical and environmental details should be taken from the DG418 manufacturer datasheet before finalizing a precision signal-chain design.

The DG418 family uses CMOS circuitry to control analog signal paths while keeping the controlled terminals electrically distinct from the logic interface. In the 1:1 configuration identified for DG418CJ+, the switch is suited to routing one signal path between circuit sections or providing isolation during measurement. Its logic levels and switching timing determine how directly it can be connected to a controller, so input thresholds, supply requirements, and allowable control-state combinations must be checked against the datasheet.

Typical applications include precision test and measurement systems, sensor isolation paths, battery-powered instrumentation, analog signal routing, and sample-and-hold or data-acquisition front ends. The 8-pin PDIP format is particularly useful for prototype boards, educational equipment, and legacy industrial designs that use through-hole DIP sockets rather than high-density surface-mount packages. The package also simplifies socketed replacement and hand soldering during engineering validation.

Designers should treat the 35 ohm maximum on-resistance as a signal-integrity constraint. Place the switch close to the protected or routed node, provide a defined return path, and evaluate the resulting attenuation against the source impedance and downstream amplifier input. State-dependent logic behavior, power rails, and unused control terminals should be validated using the manufacturer's pin-description and application guidance rather than inferred from the family name.

This product page organizes the DG418CJ+ electrical facts, package information, drop-in candidates, and practical selection guidance into one engineering reference. It also distinguishes directly compatible replacements from broader functional similarities, helping PCB designers preserve pin and footprint continuity while accounting for temperature-grade, switching-state, and application-specific requirements.

Alternatives de remplacement direct pour DG418CJ+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec DG418CJ+ (même facteur de forme et même empreinte) — différant par Switch Configuration.

Analog Devices
Switch Configuration: SPST normally open
Comparer avec DG418CJ+ →

DG418CJ

✅ Remplacement direct
📦 PDIP-8
Same DG418 SPST 1:1 configuration and 35 ohm maximum on-resistance; 0% difference in the confirmed key ratings

📋 Alternative de référence (hors catalogue)

DG418DJ+

✅ Remplacement direct
Analog Devices
📦 PDIP-8
Precision CMOS analog switch · SPST normally open · 1 channel · 35 ohm maximum · 15 V maximum · 44 V · 100 ns · 35 nW

Contactez-nous pour le prix

Voir la fiche technique →

DG418DJ+

✅ Remplacement direct
Analog Devices
📦 PDIP-8
Precision CMOS analog switch · SPST normally open · 1 channel · 35 ohm maximum · 15 V maximum · 44 V · 100 ns · 35 nW

Contactez-nous pour le prix

Voir la fiche technique →

DG418DJ-E3

✅ Remplacement direct
📦 PDIP-8
Reported as a complete package-and-terminal replacement with consistent functional characteristics; 0% difference in the confirmed key ratings

📋 Alternative de référence (hors catalogue)

DG418CJ+ Valeurs maximales et caractéristiques électriques

Product Type Precision CMOS analog switch
Number of Circuits 1 circuit
Switch Configuration 1:1
Switch Type SPST
Normal State Normally open
Maximum On-Resistance 35 ohm
Nombre de broches 8 pins
Boîtier 8-pin PDIP
Type de montage Through-hole
Statut du cycle de vie Production

Guide de configuration des broches du DG418CJ+ 8-pin pdip

Configuration des broches du DG418CJ+ (boîtier 8-pin pdip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 8-pin pdip pour le DG418CJ+

Aucune donnée de brochage détaillée disponible pour DG418CJ+.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

DG418CJ+ convient pour 6 applications: Precision Test and Measurement Systems, Sensor Signal Isolation, Battery-Powered Instrumentation, Analog Signal Routing, Data Acquisition Front Ends, Educational and Prototype Electronics.

🖥️

Precision Test and Measurement Systems

The DG418CJ+ is suitable for routing a measurement signal through a controlled analog path because it provides one SPST, normally open circuit with a maximum on-resistance of 35 ohms. The 8-pin PDIP package fits through-hole prototype and legacy instrument boards, while the normally open state provides a defined disconnected condition before control asserts the path. Because 35 ohms can create attenuation with finite source and load impedances, engineers should calculate the divider formed by switch resistance and the surrounding network. Use the manufacturer data sheet to assign control and supply pins, and validate leakage, switching transients, and bandwidth against the required measurement accuracy.

🧩

Sensor Signal Isolation

The DG418CJ+ can isolate a sensor signal by disconnecting it from the downstream measurement chain in its normally open state. Its SPST 1:1 architecture is appropriate when a source must be muted, selected, or protected without switching continuously between two throws. The confirmed 35 ohm maximum on-resistance must be included in the sensor-loading calculation, particularly for high-impedance sensors where source resistance and leakage can dominate accuracy. Place the switch near the sensor node, maintain a low-impedance return path, and verify control thresholds and supply sequencing with the DG418 manufacturer documentation.

⚡

Battery-Powered Instrumentation

A normally open analog switch helps battery-powered instruments disconnect loads or signal branches when they are not needed, reducing unintended interaction with sensitive measurement circuits. The DG418CJ+ combines that controlled isolation behavior with a documented maximum on-resistance of 35 ohms and an 8-pin PDIP package suited to socketed or through-hole designs. Account for switch loss in the power-budget and signal-budget calculations, and confirm operating temperature, supply voltage, and logic levels from the manufacturer data sheet before selecting it for a battery product.

🌐

Analog Signal Routing

The DG418CJ+ can serve as a controlled series element in analog routing networks where a signal must be connected or disconnected under digital command. Its single SPST path and 1:1 configuration simplify designs that do not require a common terminal and two throws. The 35 ohm maximum on-resistance is the principal confirmed electrical constraint and may require impedance matching, gain compensation, or placement immediately before the receiving circuit. Follow the manufacturer pin-description and application guidance for logic states and supply connections, and test channel behavior over the required signal range.

📺

Data Acquisition Front Ends

In a data-acquisition front end, the DG418CJ+ can connect or isolate an input during selection, calibration, or acquisition phases. Its normally open behavior provides a useful inactive state, and the 35 ohm maximum on-resistance is low enough for many moderate-impedance sensor paths but must still be included in error analysis. The PDIP-8 package supports prototype boards and socketed industrial equipment. Confirm switching speed, charge injection, off leakage, logic levels, and supply limits in the DG418 data sheet before using it with high-speed converters or very high source impedances.

🔧

Educational and Prototype Electronics

The 8-pin PDIP package makes the DG418CJ+ practical for educational analog-switching experiments, breadboard-oriented prototypes, and manually soldered validation boards. Students can use its normally open SPST behavior to demonstrate switched signal paths without mechanical relay wear. The confirmed 35 ohm maximum on-resistance also provides a practical example of how switch resistance affects an analog divider. The official Analog Devices DG418 page and data sheet should be used for the pinout, logic truth table, supply requirements, and absolute maximum ratings before wiring the device.

Récapitulatif des produits recommandés

DG418DJ+ Analog Devices Utilisé dans : Precision Test and Measurement Systems, Battery-Powered Instrumentation, Analog Signal Routing, Educational and Prototype Electronics DG418DJ-E3 Package- and terminal-compatible replacement candidate Utilisé dans : Precision Test and Measurement Systems, Battery-Powered Instrumentation, Educational and Prototype Electronics DG418CJ Exact DG418 PDIP ordering candidate Utilisé dans : Sensor Signal Isolation, Analog Signal Routing, Data Acquisition Front Ends DG418DJ Terminal-compatible family variant Utilisé dans : Sensor Signal Isolation, Data Acquisition Front Ends
What is the DG418CJ+?
The Analog Devices DG418CJ+ is a precision CMOS analog switch containing one SPST circuit in a 1:1 configuration. According to the Analog Devices product page for the DG418 family, the device is a production part with a maximum on-resistance of 35 ohms and is packaged in an 8-pin PDIP. Its normally open behavior disconnects the switched path in its default state, which is useful for controlled signal routing and isolation.
What are the key specifications of DG418CJ+ that engineers should know?
The principal DG418CJ+ specifications are one SPST switch, a 1:1 configuration, normally open operation, a maximum on-resistance of 35 ohms, and an 8-pin PDIP package. The Analog Devices DG418 page identifies the family as a production product and lists improved off leakage over temperature as a family feature. Supply voltage, logic thresholds, switching time, charge injection, and temperature limits must be confirmed in the manufacturer datasheet.
Where can I download the DG418CJ+ datasheet PDF?
The official DG418 documentation is available from Analog Devices through the DG418 product page at https://www.analog.com/en/products/dg418.html. From that page, open the DG418 data sheet listed under Documentation. The DG418CJ+ ordering code refers to the 8-pin PDIP configuration, so use the ordering table and pin-description section to confirm the CJ suffix, package, and electrical limits before releasing a design.
Where can I find the DG418CJ+ pinout?
The DG418CJ+ pinout is shown in the pin-configuration and pin-description sections of the manufacturer data sheet linked from the official DG418 product page. The verified component information confirms that the device has eight pins in a PDIP package. Assign PCB nets from that table because the control inputs, analog terminals, and supply pins must be connected exactly as specified for the selected logic and supply configuration.
Is DG418CJ+ suitable for precision signal-routing applications?
The DG418CJ+ can suit precision signal routing when the application tolerates its maximum 35 ohm on-resistance. That resistance can create attenuation, especially when the source impedance or downstream input impedance is high. The device is also described by Analog Devices as a precision CMOS normally open SPST switch. Validate gain error, leakage, switching transients, and control levels against the complete signal-path requirements.
What is the difference between DG418CJ+ and DG418DJ+?
The DG418CJ+ and DG418DJ+ belong to the same DG418 analog-switch family and use an 8-pin PDIP format, but their suffix-qualified ordering characteristics must be checked separately. The Analog Devices DG418 family page remains the controlling document for variants. Use its part-selection table to compare package and temperature-grade information, then confirm that the replacement satisfies the original board's electrical and environmental requirements.
When should I choose DG418CJ+ over another SPDT analog switch?
Choose the DG418CJ+ when the required circuit is one SPST path in a 1:1 configuration and an 8-pin PDIP package is appropriate. An SPDT alternative changes the terminal behavior and may assign the common and throw terminals differently, so it is not automatically a drop-in replacement. Selection should begin with the required switch topology, signal amplitude, on-resistance, leakage, supply voltage, logic thresholds, and footprint.
Can DG418DJ+ replace DG418CJ+ on an existing PCB?
A DG418DJ+ replacement is credible when the candidate is confirmed in the same 8-pin PDIP footprint and its suffix-specific electrical and temperature ratings meet the original design limits. The cross-reference information identifies DG418DJ as package- and terminal-compatible with DG418CJ and states that replacement requires no board modification. Final qualification should still include a manufacturer ordering-table review and worst-case signal-path testing.
What can replace DG418CJ+?
The closest documented replacements are the DG418 family ordering variants that retain the 8-pin PDIP footprint, including DG418DJ+ and the DG418DJ cross-reference identified as package- and terminal-compatible. A replacement should preserve the SPST 1:1 behavior, normally open state, control logic, supply arrangement, and required electrical ratings. Broad multiplexers or SPDT devices may serve similar functions but should not be assumed to be pin-compatible.
Is DG418CJ+ the same as DG418DJ-E3?
DG418DJ-E3 is identified in cross-reference information as an 8-pin PDIP alternative with consistent terminals, package, and principal functional characteristics, making it a candidate for DG418CJ replacement. It is not necessarily interchangeable in every ordering attribute. Compare the exact temperature grade, lifecycle status, package dimensions, control thresholds, and electrical limits in the manufacturer documentation before approving it.
What is the best Analog Devices equivalent for DG418CJ+?
The best documented Analog Devices-family equivalent is the DG418DJ+ because it remains within the DG418 product line and is available in the same 8-pin PDIP package family. The exact suffix characteristics must be verified through the DG418 product-selection table. For applications requiring a different switch topology, series resistance, or logic interface, the closest member of the Analog Devices DG417, DG418, or DG419 family should be selected by function rather than package alone.
How much on-resistance can DG418CJ+ introduce?
The DG418CJ+ has a maximum on-resistance of 35 ohms according to the Analog Devices DG418 product page. This series resistance can form a voltage divider with the source and destination impedances, causing attenuation and possible signal-dependent error. The practical impact depends on the selected operating point, signal amplitude, frequency, and the impedances surrounding the switch, so simulate the complete path rather than treating 35 ohms as a standalone error value.
Does DG418CJ+ require a particular power supply polarity?
The required supply arrangement and polarity must be taken from the DG418 manufacturer data sheet; the verified product information confirms the device and package but does not state the supply pins or voltage range. Do not infer dual-rail or single-rail operation from the package. Confirm the supply pins, logic reference arrangement, allowable control-state combinations, and decoupling requirements before laying out the PCB or connecting laboratory equipment.
Where can I buy DG418CJ+ and check its current price?
Use the Request a Quote form on this XAIPART product page to request current DG418CJ+ availability, commercial terms, and lead time. Quote requests allow the exact 8-pin PDIP ordering code and required quantity to be reviewed without relying on stale pricing. For technical qualification, use the linked Analog Devices DG418 product page and data sheet rather than assuming that a distributor listing contains the complete electrical specification.
What is the lead time and stock status for DG418CJ+?
Current stock and lead time for DG418CJ+ should be requested through the Request a Quote form on this XAIPART page. The official Analog Devices page identifies the DG418 family as a production product, but that statement does not by itself confirm local inventory, allocation, or a shipment date. Include your required quantity, date code, inspection requirements, and delivery schedule so the manufacturing and sourcing team can respond accurately.
Why should a precision analog switch be placed close to the signal node?
Placing the DG418CJ+ close to its switched signal node limits the length of high-impedance traces and reduces susceptibility to capacitive pickup, crosstalk, and leakage effects. The 35 ohm maximum on-resistance already contributes series attenuation, so additional trace resistance can worsen error in high-impedance circuits. Provide a continuous return path, keep sensitive analog routing compact, and compare switching transients with the measurement bandwidth of the application.

Données de référence d'ingénierie pour DG418CJ+ — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the DG418CJ+ when the design requires one normally open SPST path with a 1:1 configuration, a maximum on-resistance of 35 ohms, and an 8-pin PDIP footprint. DG418CJ and DG418DJ+ are preferred first checks when the objective is to preserve the Analog Devices DG418 family and its documented electrical behavior. DG418DJ and DG418DJ-E3 are useful when their suffix-specific ratings and lifecycle terms meet the original requirements, but each still requires manufacturer-table review and signal-path validation. Do not select an SPDT device solely because it uses an 8-pin DIP package: a common terminal and two throws are not functionally interchangeable with the DG418CJ+ 1:1 SPST path. Final selection should also confirm supply voltage, logic thresholds, leakage, switching speed, charge injection, and operating temperature.

Comparaison avec les alternatives

Paramètre Ce produit DG418CJ DG418DJ+ DG418DJ DG418DJ-E3
Package PDIP-8 PDIP-8 PDIP-8 PDIP-8 PDIP-8
Brand Analog Devices Analog Devices Analog Devices Analog Devices Vishay Intertechnology
Switch Type SPST SPST SPST SPST SPST
Configuration 1:1 1:1 1:1 1:1 1:1
Maximum On-Resistance 35 ohm 35 ohm 35 ohm 35 ohm 35 ohm
Normal State Normally open Normally open Normally open Normally open Normally open
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Number of Pins 8 pins 8 pins 8 pins 8 pins 8 pins

Principaux différenciateurs

  • Maintains a single normally open SPST signal path (vs MAX318CPA+)
  • Uses the established DG418 family pin and application framework (vs DG418DJ-E3)
  • Through-hole PDIP-8 construction supports socketed serviceability (vs MAX318CPA+)

Notes de conception

Include the DG418CJ+ maximum on-resistance of 35 ohms in the complete signal-path divider calculation with the source impedance, destination impedance, PCB trace resistance, and any intentional attenuation network. Place the switch near the node that must be isolated so that sensitive high-impedance traces are not left unnecessarily long. For fast or high-amplitude signals, evaluate switch capacitance and charge injection from the manufacturer data sheet because the confirmed 35 ohm rating alone does not establish total dynamic error.

Use the manufacturer's pin-description table when assigning every package connection, including control inputs, supply terminals, and any unused pins. Keep the analog switch's switched-node traces short, provide a continuous ground reference beneath the routing area, and place input and output decoupling components close to their associated device pins. Because this is an 8-pin PDIP package, confirm hole spacing, row spacing, lead length, and socket compatibility against the official mechanical drawing before releasing artwork.

Do not treat every SPST, normally open, or PDIP analog switch as interchangeable. A candidate is a valid drop-in only when its terminal assignments, control truth table, supply arrangement, electrical limits, and package dimensions match the original design. After replacement, verify both switch states with the intended source and load impedances, and check that the inactive leakage and switching transients meet the application's error budget.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The verified product information identifies the DG418 family as a production product but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. This analog interface IC is not presented as an automotive-qualified AEC-Q100 device.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

DG418CJ+ datasheet DG418CJ+ datasheet pdf DG418CJ+ pinout DG418CJ+ specifications Analog Devices DG418CJ+ DG418CJ+ 35 ohm DG418CJ+ PDIP-8 DG418CJ+ SPST switch DG418CJ+ replacement DG418CJ+ equivalent DG418CJ+ price DG418CJ+ stock DG418CJ+ vs DG418DJ+ DG418CJ+ analog switch application DG418CJ+ cross reference

Composants & termes associés

Analog Devices Maxim Integrated DG418CJ+ DG418CJ DG418DJ+ DG418DJ DG418DJ-E3 DG418 precision CMOS analog switch SPST normally open switch multiplexer demultiplexer interface IC semiconductor PDIP-8 DIP package through-hole package 35 ohm on-resistance off leakage charge injection analog signal routing test and measurement RoHS REACH
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ