DG418CJ+ - 35 Ohm SPST Analog Switch | Analog Devices
MPN: DG418CJ+ ✓ सक्रियDG418CJ+ अवलोकन
An analog switch is an interface integrated circuit that connects or disconnects an analog signal path under digital control. Within the semiconductor hierarchy, the DG418CJ+ is an analog switch, a member of the multiplexer and demultiplexer family, and an interface IC used between sensors, measurement circuits, converters, and digital control logic. Unlike a mechanical relay, it can switch without moving physical contacts and can therefore support compact, repeatable signal control.
Key characteristics include a maximum on-resistance of 35 ohms, SPST switching, normally open operation, and an 8-pin PDIP package. The on-resistance specification is important because series resistance can produce signal attenuation and voltage-dependent error in divider networks. The normally open state also provides a useful default: the switched path remains disconnected until the control input asserts the switch. Additional electrical and environmental details should be taken from the DG418 manufacturer datasheet before finalizing a precision signal-chain design.
The DG418 family uses CMOS circuitry to control analog signal paths while keeping the controlled terminals electrically distinct from the logic interface. In the 1:1 configuration identified for DG418CJ+, the switch is suited to routing one signal path between circuit sections or providing isolation during measurement. Its logic levels and switching timing determine how directly it can be connected to a controller, so input thresholds, supply requirements, and allowable control-state combinations must be checked against the datasheet.
Typical applications include precision test and measurement systems, sensor isolation paths, battery-powered instrumentation, analog signal routing, and sample-and-hold or data-acquisition front ends. The 8-pin PDIP format is particularly useful for prototype boards, educational equipment, and legacy industrial designs that use through-hole DIP sockets rather than high-density surface-mount packages. The package also simplifies socketed replacement and hand soldering during engineering validation.
Designers should treat the 35 ohm maximum on-resistance as a signal-integrity constraint. Place the switch close to the protected or routed node, provide a defined return path, and evaluate the resulting attenuation against the source impedance and downstream amplifier input. State-dependent logic behavior, power rails, and unused control terminals should be validated using the manufacturer's pin-description and application guidance rather than inferred from the family name.
This product page organizes the DG418CJ+ electrical facts, package information, drop-in candidates, and practical selection guidance into one engineering reference. It also distinguishes directly compatible replacements from broader functional similarities, helping PCB designers preserve pin and footprint continuity while accounting for temperature-grade, switching-state, and application-specific requirements.
के लिए ड्रॉप-इन विकल्प DG418CJ+ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं DG418CJ+ (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Switch Configuration.
DG418CJ
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG418DJ+
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →DG418DJ+
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →DG418DJ-E3
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
DG418CJ+ Maximum Ratings और Electrical Characteristics
| Product Type | Precision CMOS analog switch |
| Number of Circuits | 1 circuit |
| Switch Configuration | 1:1 |
| Switch Type | SPST |
| Normal State | Normally open |
| Maximum On-Resistance | 35 ohm |
| पिन की संख्या | 8 pins |
| पैकेज | 8-pin PDIP |
| माउंटिंग प्रकार | Through-hole |
| लाइफसाइकिल स्थिति | Production |
DG418CJ+ 8-pin pdip पिन कॉन्फ़िगरेशन गाइड
DG418CJ+ (8-pin pdip पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: DG418CJ+.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
DG418CJ+ के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Test and Measurement Systems, Sensor Signal Isolation, Battery-Powered Instrumentation, Analog Signal Routing, Data Acquisition Front Ends, Educational and Prototype Electronics.
Precision Test and Measurement Systems
The DG418CJ+ is suitable for routing a measurement signal through a controlled analog path because it provides one SPST, normally open circuit with a maximum on-resistance of 35 ohms. The 8-pin PDIP package fits through-hole prototype and legacy instrument boards, while the normally open state provides a defined disconnected condition before control asserts the path. Because 35 ohms can create attenuation with finite source and load impedances, engineers should calculate the divider formed by switch resistance and the surrounding network. Use the manufacturer data sheet to assign control and supply pins, and validate leakage, switching transients, and bandwidth against the required measurement accuracy.
अनुशंसित
Sensor Signal Isolation
The DG418CJ+ can isolate a sensor signal by disconnecting it from the downstream measurement chain in its normally open state. Its SPST 1:1 architecture is appropriate when a source must be muted, selected, or protected without switching continuously between two throws. The confirmed 35 ohm maximum on-resistance must be included in the sensor-loading calculation, particularly for high-impedance sensors where source resistance and leakage can dominate accuracy. Place the switch near the sensor node, maintain a low-impedance return path, and verify control thresholds and supply sequencing with the DG418 manufacturer documentation.
अनुशंसित
Battery-Powered Instrumentation
A normally open analog switch helps battery-powered instruments disconnect loads or signal branches when they are not needed, reducing unintended interaction with sensitive measurement circuits. The DG418CJ+ combines that controlled isolation behavior with a documented maximum on-resistance of 35 ohms and an 8-pin PDIP package suited to socketed or through-hole designs. Account for switch loss in the power-budget and signal-budget calculations, and confirm operating temperature, supply voltage, and logic levels from the manufacturer data sheet before selecting it for a battery product.
अनुशंसित
Analog Signal Routing
The DG418CJ+ can serve as a controlled series element in analog routing networks where a signal must be connected or disconnected under digital command. Its single SPST path and 1:1 configuration simplify designs that do not require a common terminal and two throws. The 35 ohm maximum on-resistance is the principal confirmed electrical constraint and may require impedance matching, gain compensation, or placement immediately before the receiving circuit. Follow the manufacturer pin-description and application guidance for logic states and supply connections, and test channel behavior over the required signal range.
अनुशंसित
Data Acquisition Front Ends
In a data-acquisition front end, the DG418CJ+ can connect or isolate an input during selection, calibration, or acquisition phases. Its normally open behavior provides a useful inactive state, and the 35 ohm maximum on-resistance is low enough for many moderate-impedance sensor paths but must still be included in error analysis. The PDIP-8 package supports prototype boards and socketed industrial equipment. Confirm switching speed, charge injection, off leakage, logic levels, and supply limits in the DG418 data sheet before using it with high-speed converters or very high source impedances.
अनुशंसित
Educational and Prototype Electronics
The 8-pin PDIP package makes the DG418CJ+ practical for educational analog-switching experiments, breadboard-oriented prototypes, and manually soldered validation boards. Students can use its normally open SPST behavior to demonstrate switched signal paths without mechanical relay wear. The confirmed 35 ohm maximum on-resistance also provides a practical example of how switch resistance affects an analog divider. The official Analog Devices DG418 page and data sheet should be used for the pinout, logic truth table, supply requirements, and absolute maximum ratings before wiring the device.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा DG418CJ+ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | DG418CJ | DG418DJ+ | DG418DJ | DG418DJ-E3 |
|---|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology |
| Switch Type | SPST | SPST | SPST | SPST | SPST |
| Configuration | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| Maximum On-Resistance | 35 ohm | 35 ohm | 35 ohm | 35 ohm | 35 ohm |
| Normal State | Normally open | Normally open | Normally open | Normally open | Normally open |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
मुख्य विशेषताएँ
- Maintains a single normally open SPST signal path (बनामMAX318CPA+)
- Uses the established DG418 family pin and application framework (बनामDG418DJ-E3)
- Through-hole PDIP-8 construction supports socketed serviceability (बनामMAX318CPA+)
डिज़ाइन नोट्स
Include the DG418CJ+ maximum on-resistance of 35 ohms in the complete signal-path divider calculation with the source impedance, destination impedance, PCB trace resistance, and any intentional attenuation network. Place the switch near the node that must be isolated so that sensitive high-impedance traces are not left unnecessarily long. For fast or high-amplitude signals, evaluate switch capacitance and charge injection from the manufacturer data sheet because the confirmed 35 ohm rating alone does not establish total dynamic error.
Use the manufacturer's pin-description table when assigning every package connection, including control inputs, supply terminals, and any unused pins. Keep the analog switch's switched-node traces short, provide a continuous ground reference beneath the routing area, and place input and output decoupling components close to their associated device pins. Because this is an 8-pin PDIP package, confirm hole spacing, row spacing, lead length, and socket compatibility against the official mechanical drawing before releasing artwork.
Do not treat every SPST, normally open, or PDIP analog switch as interchangeable. A candidate is a valid drop-in only when its terminal assignments, control truth table, supply arrangement, electrical limits, and package dimensions match the original design. After replacement, verify both switch states with the intended source and load impedances, and check that the inactive leakage and switching transients meet the application's error budget.
अनुपालन जानकारी
The verified product information identifies the DG418 family as a production product but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. This analog interface IC is not presented as an automotive-qualified AEC-Q100 device.