DP83223VX - 5V Twister Transceiver | Texas Instruments
Référence : DP83223VX ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.75 | $6,75 |
| 10 | $6.75 | $67,50 |
| 100 | $6.75 | $675,00 |
| 500 | $6.75 | $3 375,00 |
| 1 000 | $6.75 | $6 750,00 |
DP83223VX Présentation
A network transceiver is an interface IC that converts logic-level signals into physical-layer signals suitable for a wired network and converts received signals back into usable digital data. In the hierarchy, the DP83223VX is a network interface transceiver, a communications interface IC, and a semiconductor. TWISTER describes the physical-layer signal-processing approach used for differential twisted-pair networking rather than a modern two-wire interface standard.
The verified information identifies a transceiver configuration, a 4.75 V to 5.25 V operating supply, and a 28-PLCC J-lead package. Distributor listings classify the part as a driver, receiver, and transceiver, while a technical listing describes it as a high-speed physical-layer device for shielded or unshielded twisted-pair cabling. Detailed data rates, driver and receiver counts, cable reach, termination requirements, and electrical timing limits were not supplied in the verified data and must be confirmed from the manufacturer datasheet before design release.
The PLCC package provides a through-hole-style surface-mount form factor with J-shaped leads and a compact 11.51 mm by 11.51 mm body. Its legacy package and interface function make careful footprint verification important when comparing it with modern Ethernet devices. Board layout must preserve the manufacturer's recommended network-line separation, component spacing, grounding, and termination arrangement; the available search excerpts do not provide enough detail to specify those values safely.
Potential uses include legacy high-speed network interface equipment, industrial data links, embedded communications controllers, and telecommunications equipment using compatible twisted-pair signaling. The device should be selected only after confirming the protocol, signaling rate, cable type, connector, isolation requirements, and exact pinout against the authoritative datasheet. A modern PHY or Ethernet transceiver may offer different compliance, topology, and supply characteristics and therefore is not automatically interchangeable.
For a new layout, do not infer pin assignments from the distributor package title. Obtain the DP83223 datasheet, compare every power, ground, driver, receiver, enable, and network-line connection, and validate the assembled channel with the intended cable and system load. This page synthesizes the supplied manufacturer-linked search results, distributor availability references, package information, and sourcing guidance; missing electrical values are deliberately not guessed.
Alternatives de remplacement direct pour DP83223VX — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DP83223VX (même facteur de forme et même empreinte) — différant par Package.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DP83223V
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →DP8392CV-1
✅ Remplacement direct✓ En stock
$9.75 / unité
Voir la fiche technique →DP83223VX Spécifications
| Device Type | TWISTER high-speed networking transceiver |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Boîtier | 28-PLCC J-lead |
| Package Body Size | 11.51 mm x 11.51 mm |
| Nombre de broches | 28 pins |
| Style de montage | Surface mount through PLCC J-leads |
| Network Medium | Shielded or unshielded twisted-pair cable |
| Interface Classification | Driver, receiver, and transceiver |
| Physical-Layer Function | High-speed twisted-pair line driving and signal processing |
| Manufacturer | National Semiconductor, now associated with Texas Instruments |
Guide de configuration des broches du DP83223VX 11.51 mm x 11.51 mm
Configuration des broches du DP83223VX (boîtier 11.51 mm x 11.51 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DP83223VX.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DP83223VX convient pour 6 applications: Legacy High-Speed Network Interface Equipment, Industrial Twisted-Pair Data Links, Telecommunications Network Interfaces, Embedded Communications Equipment, Legacy Network Interface Card Replacement, Mixed Legacy and Modern Network Equipment.
Legacy High-Speed Network Interface Equipment
The DP83223VX fits a legacy high-speed twisted-pair network interface where a 5 V physical-layer transceiver is required and the system already uses the TWISTER line architecture. Its verified 4.75 V to 5.25 V supply range and 28-pin PLCC package make it suitable for equipment designed around a National Semiconductor network interface. The designer must verify the exact signaling rate, pinout, cable reach, and termination network in the manufacturer datasheet. Because the available excerpts do not provide timing or reach values, this application should be treated as a legacy-platform fit, not a universal replacement for current Ethernet PHYs.
Recommandé
Industrial Twisted-Pair Data Links
DP83223VX can be used in industrial equipment that connects a controller or embedded processor to a compatible high-speed twisted-pair physical layer. The 5 V operating range and transceiver classification suit established equipment designed around this legacy interface, while the PLCC package permits inspection and rework after soldering. Industrial deployment still requires checking temperature range, isolation, grounding, cable length, and electromagnetic-emissions requirements. Those specifications are not present in the supplied excerpts, so the part should not be approved for a new industrial link without manufacturer documentation and board-level validation.
Recommandé
Telecommunications Network Interfaces
The DP83223VX may be appropriate for telecommunications or data-communication equipment that uses the original TWISTER physical-layer interface over shielded or unshielded twisted pair. Its verified function is line driving and signal processing rather than a complete protocol controller, so the surrounding system must provide compatible framing, clocking, and link management. The 28-pin PLCC package is convenient for repair-oriented and legacy production equipment, but its footprint must be checked against the exact PCB library. Confirm maximum data rate, cable reach, isolation, and termination before integrating it into a new telecom design.
Recommandé
Embedded Communications Equipment
DP83223VX can support embedded communications equipment that was designed around a dedicated twisted-pair physical layer and 5 V interface supply. The device should be placed between the digital controller and the network medium, with the exact transceiver pins connected according to the manufacturer diagram rather than inferred from distributor labels. Its fixed 28-PLCC package simplifies reuse of an existing board but makes footprint and pinout verification critical. The available data does not confirm modern compliance, maximum link length, or operating temperature, so validation should include an eye diagram or equivalent signal-integrity test on the intended cable.
Recommandé
Legacy Network Interface Card Replacement
DP83223VX is a practical candidate for maintaining or repairing a legacy network interface card built around the original TWISTER transceiver architecture. The available distributor listings identify the device as in stock or available, and the package is identified as 28-PLCC J-lead. Before ordering, compare the existing board's pin numbers, supply rails, network pair assignment, termination, and connector pinout with the exact manufacturer documentation. Do not substitute a PLCC device solely because the pin count matches; the supplied cross-reference results do not establish a universal drop-in replacement.
Recommandé
Mixed Legacy and Modern Network Equipment
DP83223VX may be useful at the boundary between older TWISTER-based equipment and a modern embedded network controller, provided the protocols, physical layers, and signal levels are explicitly matched. The 5 V transceiver can serve as the physical-layer element in an established architecture, while a modern controller handles higher-level networking functions. The design should include separate review of clocking, frame format, isolation, and cable topology because none of those details is supplied in the verified snippets. This approach is suitable for brownfield integration, not as a drop-in substitute for an unrelated Ethernet PHY.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DP83223VX — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DP83223V | DP8392CV-1 |
|---|---|---|---|
| Package | 28-PLCC J-lead | 28-PLCC J-lead | 28-PLCC J-lead |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Function | TWISTER high-speed networking transceiver | DP83223 family networking transceiver | Network interface transceiver candidate |
| Pin Count | 28 pins | 28 pins indicated by family reference | 28-PLCC indicated by comparison reference |
Principaux différenciateurs
- Verified legacy physical-layer positioning (vs DP8392CV-1)
- Documented 5 V supply window (vs DP8392CV-1)
- Specific family naming (vs DP83223V)
Notes de conception
Use the exact 28-PLCC J-lead land pattern from the manufacturer documentation and verify lead numbering before fabrication. The verified distributor description identifies a 28-pin PLCC package, but the supplied data does not include the pin map or recommended footprint. Confirm pin 1 orientation, body clearance, lead length, solder mask, and paste or through-hole assembly requirements against the authoritative drawing.
Keep the twisted-pair route short, appropriately coupled, and isolated from unrelated high-speed signals. The verified data identifies shielded or unshielded twisted-pair operation but does not provide trace impedance, pair separation, connector launch, or termination values. Copy the manufacturer reference layout and validate differential waveform, skew, reflections, and conducted emissions on the intended cable rather than estimating those values.
Do not treat a 28-pin PLCC package as proof of electrical compatibility. Verify supply voltage, pin functions, driver and receiver requirements, cable topology, termination, and timing for every proposed substitute. The available cross-reference results identify DP83223V and DP8392CV-1 as candidates but do not provide complete equivalence data; board-level qualification and schematic comparison are mandatory before replacement.
Informations de conformité
The supplied distributor and search snippets do not provide verified RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. No compliance claim should be inferred from distributor availability.
