DS90CR211MTDX - 21-Bit LVDS Channel Link Transmitter | TI
Référence : DS90CR211MTDX ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.97 | $4,97 |
| 10 | $4.47 | $44,70 |
| 100 | $3.98 | $398,00 |
| 500 | $3.58 | $1 790,00 |
| 1 000 | $3.18 | $3 180,00 |
DS90CR211MTDX Présentation
Channel Link is a proprietary high-speed digital interface technology developed by National Semiconductor (now part of Texas Instruments) that reduces the number of parallel data lines by serializing them into LVDS pairs. This technology is widely used in flat panel displays, digital video interfaces, and other applications requiring high bandwidth over a limited number of wires. The DS90CR211MTDX is part of the Channel Link family, which includes transmitters and receivers that work together to provide a complete serialization/deserialization solution.
Key features of the DS90CR211MTDX include a 21-bit parallel input, three LVDS data outputs plus one clock output, and a maximum data rate of 840 Mbps. The device has a typical power consumption of and supports a wide operating temperature range of -40°C to +85°C. The LVDS outputs feature low voltage swing (typically 350 mV) and high noise immunity, making the device ideal for noisy industrial environments. The transmitter also includes a power-down mode to reduce power consumption when not in use.
The DS90CR211MTDX uses a phase-locked loop (PLL) to generate the high-speed serial clock from the parallel input clock. The PLL ensures low jitter and accurate data alignment, which is critical for reliable data transmission at high speeds. The device also features built-in termination resistors on the LVDS outputs, simplifying PCB layout and reducing external component count. The TSSOP package offers a compact footprint with a 0.65mm lead pitch, suitable for space-constrained designs.
Typical applications include flat panel displays, digital video interfaces, industrial cameras, medical imaging, and automotive infotainment systems. The device is particularly well-suited for applications requiring high-speed data transfer over long distances with minimal EMI, as LVDS signaling inherently provides low electromagnetic interference. The DS90CR211MTDX is also used in test and measurement equipment where high-speed data acquisition is required.
When designing with the DS90CR211MTDX, ensure that the LVDS output traces are impedance-matched (typically 100Ω differential) and kept as short as possible to minimize signal integrity issues. The power supply should be well-decoupled with 0.1µF and 10µF capacitors placed close to the VCC pins. The PLL requires a clean power supply to achieve optimal jitter performance, so avoid routing the power traces near high-speed switching signals.
Alternatives de remplacement direct pour DS90CR211MTDX — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DS90CR211MTDX/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR211MTD
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR211MTDX Spécifications
| Type | Transmitter |
| Protocol | LVDS |
| Number of Drivers/Receivers | 1/0 |
| Tension d'alimentation | 4.5 V to 5.5 V |
| Boîtier / Format | 48-TFSOP (0.240", 6.10mm Width) |
| Nombre de broches | 48 |
| Débit de données | 840 Mbps |
| Input Data Width | 21 bits |
| Number of LVDS Data Pairs | 3 |
| Number of LVDS Clock Pairs | 1 |
| Plage de température de fonctionnement | -40°C to +85°C |
| Type de montage | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
Configuration des broches de DS90CR211MTDX
| Broche 1 | VCC — Power supply (4.5V to 5.5V) |
| Broche 2 | GND — Ground |
| Broche 3 | IN0 — Parallel data input bit 0 |
| Broche 4 | IN1 — Parallel data input bit 1 |
| Broche 5 | IN2 — Parallel data input bit 2 |
| Broche 6 | IN3 — Parallel data input bit 3 |
| Broche 7 | IN4 — Parallel data input bit 4 |
| Broche 8 | IN5 — Parallel data input bit 5 |
| Broche 9 | IN6 — Parallel data input bit 6 |
| Broche 10 | IN7 — Parallel data input bit 7 |
| Broche 11 | IN8 — Parallel data input bit 8 |
| Broche 12 | IN9 — Parallel data input bit 9 |
| Broche 13 | IN10 — Parallel data input bit 10 |
| Broche 14 | IN11 — Parallel data input bit 11 |
| Broche 15 | IN12 — Parallel data input bit 12 |
| Broche 16 | IN13 — Parallel data input bit 13 |
| Broche 17 | IN14 — Parallel data input bit 14 |
| Broche 18 | IN15 — Parallel data input bit 15 |
| Broche 19 | IN16 — Parallel data input bit 16 |
| Broche 20 | IN17 — Parallel data input bit 17 |
| Broche 21 | IN18 — Parallel data input bit 18 |
| Broche 22 | IN19 — Parallel data input bit 19 |
| Broche 23 | IN20 — Parallel data input bit 20 |
| Broche 24 | CLKIN — Parallel input clock |
| Broche 25 | PLLVCC — PLL power supply (decouple with 0.1µF) |
| Broche 26 | PLLGND — PLL ground |
| Broche 27 | LVDSOUT0+ — LVDS data output 0 positive |
| Broche 28 | LVDSOUT0- — LVDS data output 0 negative |
| Broche 29 | LVDSOUT1+ — LVDS data output 1 positive |
| Broche 30 | LVDSOUT1- — LVDS data output 1 negative |
| Broche 31 | LVDSOUT2+ — LVDS data output 2 positive |
| Broche 32 | LVDSOUT2- — LVDS data output 2 negative |
| Broche 33 | LVDSCLK+ — LVDS clock output positive |
| Broche 34 | LVDSCCLK- — LVDS clock output negative |
| Broche 35 | GND — Ground |
| Broche 36 | VCC — Power supply |
| Broche 37 | PDWN — Power down (active low) |
| Broche 38 | NC — No connect |
| Broche 39 | NC — No connect |
| Broche 40 | NC — No connect |
| Broche 41 | NC — No connect |
| Broche 42 | NC — No connect |
| Broche 43 | NC — No connect |
| Broche 44 | NC — No connect |
| Broche 45 | NC — No connect |
| Broche 46 | NC — No connect |
| Broche 47 | NC — No connect |
| Broche 48 | NC — No connect |
Applications typiques
DS90CR211MTDX convient pour 6 applications: Flat Panel Displays, Industrial Cameras, Medical Imaging, Automotive Infotainment, Test and Measurement, Digital Video Interfaces.
Flat Panel Displays
The DS90CR211MTDX is used to transmit RGB video data from a graphics controller to a flat panel display. Its 21-bit parallel input matches the 18-bit or 24-bit RGB interfaces, and the LVDS output reduces the number of cables needed. The 840 Mbps data rate supports resolutions up to WXGA (1366x768) at 60 Hz. The low EMI of LVDS ensures clean signal transmission in consumer electronics.
Recommandé
Industrial Cameras
In industrial machine vision systems, the DS90CR211MTDX transmits high-speed image data from a camera sensor to a processing unit. The 21-bit width accommodates 10-bit or 12-bit pixel data with synchronization signals. The wide operating temperature range (-40°C to +85°C) and robust LVDS signaling make it suitable for harsh factory environments. The serialized output reduces cable cost and improves reliability.
Recommandé
Medical Imaging
The DS90CR211MTDX is used in medical imaging devices such as ultrasound and endoscopy systems to transmit high-resolution video data. The low power consumption and small package are advantageous for portable devices. The LVDS interface provides high noise immunity, which is critical in medical environments with electromagnetic interference. The 840 Mbps data rate supports high-frame-rate imaging.
Recommandé
Automotive Infotainment
The DS90CR211MTDX is used in automotive infotainment systems to transmit video data from a head unit to a display. The LVDS interface reduces EMI, which is important for compliance with automotive EMC standards. The device operates over the automotive temperature range and can handle the vibration and temperature extremes of a vehicle environment. The 21-bit width supports various display resolutions.
Recommandé
Test and Measurement
In test and measurement equipment, the DS90CR211MTDX is used to transmit high-speed digital data from an acquisition board to a host processor. The low jitter and high data rate ensure accurate data transfer. The small package allows for dense PCB layouts. The device's power-down mode helps reduce power consumption in battery-operated instruments.
Recommandé
Digital Video Interfaces
The DS90CR211MTDX is used in digital video interfaces for projectors, video walls, and signage. It serializes 21-bit parallel video data into LVDS, reducing the number of interconnects and improving signal integrity over longer distances. The 840 Mbps data rate supports high-definition video formats. The device's robust design ensures reliable operation in commercial environments.
Recommandé
Données de référence d'ingénierie pour DS90CR211MTDX — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DS90CR211MTDX/NOPB | DS90CR211MTD | DS90CR213MTDX |
|---|---|---|---|---|
| Package | 48-TFSOP (0.240", 6.10mm Width) | 48-TFSOP (0.240", 6.10mm Width) | 48-TFSOP (0.240", 6.10mm Width) | 56-TFSOP (0.240", 6.10mm Width) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V |
| Data Rate | 840 Mbps | 840 Mbps | 840 Mbps | 840 Mbps |
| Input Data Width | 21 bits | 21 bits | 21 bits | 21 bits |
| Number of LVDS Data Pairs | 3 | 3 | 3 | 3 |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| RoHS Compliant | Yes | Yes | No | Yes |
Principaux différenciateurs
- Lead-free version available (vs DS90CR211MTD)
- Pin-compatible with DS90CR211MTD (vs DS90CR213MTDX)
- Lower pin count for 21-bit interface (vs DS90CR561MTDX)
Notes de conception
For optimal signal integrity, route the LVDS output pairs as 100Ω differential pairs with controlled impedance. Keep the traces as short as possible and avoid vias. Place a 100Ω termination resistor across each LVDS pair at the receiver end. The PLL power supply (PLLVCC) should be decoupled with a 0.1µF capacitor placed as close to the pin as possible.
The DS90CR211MTDX requires a clean 4.5V to 5.5V supply. Use a 10µF bulk capacitor and a 0.1µF ceramic capacitor near the VCC pins. The PLLVCC pin should have its own 0.1µF capacitor to minimize noise coupling into the PLL, which could increase jitter on the LVDS outputs.
Ensure the parallel input clock (CLKIN) is clean and has low jitter, as it directly affects the LVDS output jitter. Avoid routing CLKIN near high-speed switching signals. The power-down pin (PDWN) is active low; tie it high if not used. Do not leave unused inputs floating; tie them to GND or VCC as appropriate.
Informations de conformité
RoHS compliant and lead-free per distributor listings. Not AEC-Q100 qualified.
