Texas Instruments

DS90CR286AMTDX - 28-Bit LVDS Receiver | Texas Instruments

Référence : DS90CR286AMTDX ✓ Actif
3.3 V Vdss DGG TSSOP, 56 pins Package 66 MHz Speed
MOQ : 1 |

DS90CR286AMTDX Présentation

Texas Instruments DS90CR286AMTDX is a 3.3 V rising-edge data-strobe LVDS receiver designed for 28-bit Channel Link transfers at up to 66 MHz. The device is offered in a 56-pin DGG TSSOP package and supports a -40°C to 85°C operating-temperature range.

An LVDS receiver is an interface circuit that converts low-voltage differential signaling into a logic-level output. It belongs to the signal-chain hierarchy of transceiver ICs, interface ICs, and semiconductors. LVDS, or Low-Voltage Differential Signaling, provides a noise-resistant method for transferring high-speed data across a cable or PCB link while using low signal amplitudes. The DS90CR286A family is intended for parallel-to-serial data-strobe connections between processors, controllers, displays, imaging equipment, and other digital systems.

The receiver accepts eight LVDS data channels plus a differential clock, reconstructs the parallel data at the receiver, and supplies a data-strobe clock output. Its 20 MHz to 66 MHz shift-clock support and 50% receiver-output-clock duty cycle are important for systems that transfer wide parallel data over a compact differential link. The manufacturer also identifies compatibility with the TIA/EIA-644 LVDS standard, low-profile 56-pin or 48-pin DGG TSSOP options, and an automotive-qualified Grade 3 option within the DS90CR286A family.

Channel Link is a parallel bus architecture that separates data and clock rather than relying on source-synchronous clocking. This arrangement can simplify implementation in older computing, industrial-control, display, and machine-vision systems. By carrying data and clock across balanced differential lines, the interface reduces sensitivity to common-mode noise and can support reliable transmission where a single-ended bus would be more susceptible to crosstalk and ground-offset problems.

Typical uses include industrial imaging systems, video-processing equipment, display controllers, printers, machine-vision hardware, and embedded parallel-bus interfaces. When implementing the receiver, preserve the differential pair geometry specified by the manufacturer, provide an appropriate LVDS termination and bias network at the transmitter side, and route the recovered clock and data outputs as ordinary single-ended digital signals. Keep the receiver and its decoupling capacitors close to the source impedance and observe the recommended layer-stack and return-path arrangement to minimize edge degradation.

For clock-sensitive designs, check receiver output setup and hold timing against the receiving logic rather than relying only on the 66 MHz clock limit. The automotive Grade 3 variant should be selected only when the complete system requires that qualification; the DS90CR286AMTDX ordering designation must also be checked for its exact package, temperature range, reel or tube configuration, and lead-free status before placement. This page combines family-level specifications, ordering distinctions, drop-in candidates, and interface-level design guidance to simplify component selection and PCB integration.

Alternatives de remplacement direct pour DS90CR286AMTDX — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

DS90CR286AMTDX/NOPB

✅ Remplacement direct
📦 56-pin DGG TSSOP
Same 28-bit, 3.3 V, 66 MHz receiver family and 56-pin DGG TSSOP; ordering designation changes to the /NOPB no-lead-finish configuration, a 0% electrical key-parameter difference.

📋 Alternative de référence (hors catalogue)

DS90CR286AMTD/NOPB

✅ Remplacement direct
📦 56-pin DGG TSSOP
Same 3.3 V, 28-bit, 66 MHz LVDS receiver family and 56-pin DGG TSSOP footprint; the documented ordering code differs by the AMTD versus AMTDX suffix, with a 0% core electrical difference indicated.

📋 Alternative de référence (hors catalogue)

DS90CR286MTD

✅ Remplacement direct
Texas Instruments
📦 56-pin DGG TSSOP
28-bit channel-link LVDS receiver · 3.3 V · 28 bits · 66 MHz · 462 Mbps · LVDS · LVCMOS/LVTTL · Rising edge

Contactez-nous pour le prix

Voir la fiche technique →

DS90CR286AMTD

✅ Remplacement direct
📦 56-pin DGG TSSOP
Same 28-bit, 3.3 V, 66 MHz LVDS receiver family and 56-pin DGG TSSOP footprint; the listed ordering designation differs from DS90CR286AMTDX by the final suffix, with a 0% core electrical difference indicated.

📋 Alternative de référence (hors catalogue)

DS90CR286AMTDX Spécifications

Product Type 28-bit LVDS data-strobe receiver
Tension d'alimentation 3.3 V
Fréquence d'horloge maximale 66 MHz
Minimum Shift Clock Frequency 20 MHz
Channel Width 28 bits
Signaling Standard TIA/EIA-644 LVDS
Data Transfer Edge Rising edge
Receiver Output Clock Duty Cycle 50%
Plage de température de fonctionnement -40°C to 85°C
Boîtier DGG TSSOP, 56 pins
Package Type Low-profile TSSOP
Automotive Qualification AEC-Q100 Grade 3 option available in DS90CR286A family
Receiver Power Consumption <270 mW
Output Timing Best-in-class set and hold times on receiver outputs; exact values require datasheet review
Nombre de broches 56 pins

Guide de configuration des broches du DS90CR286AMTDX low-profile tssop

Configuration des broches du DS90CR286AMTDX (boîtier low-profile tssop). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier low-profile tssop pour le DS90CR286AMTDX

Aucune donnée de brochage détaillée disponible pour DS90CR286AMTDX.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

DS90CR286AMTDX convient pour 6 applications: Industrial Machine-Vision Systems, Digital Video Processing, Display Controller Interconnects, Printer and Imaging Equipment, Industrial Control and Data Acquisition, Security and Surveillance Equipment.

🏭

Industrial Machine-Vision Systems

The DS90CR286AMTDX fits industrial machine-vision controllers that transfer a 28-bit parallel payload and a separate clock over an LVDS Channel Link. Its 3.3 V supply, 20 MHz-to-66 MHz clock range, and rising-edge data-strobe operation provide a defined interface for camera or image-processing subsystems. The differential receiver helps reduce susceptibility to common-mode disturbance encountered in industrial environments. Board implementation should preserve controlled differential geometry, provide the manufacturer-specified termination and bias network, and validate receiver output timing against the downstream image processor. The -40°C-to-85°C range supports equipment operating across typical industrial temperature conditions, although final enclosure temperature and system qualification remain separate design requirements.

📺

Digital Video Processing

The DS90CR286AMTDX is appropriate for digital video modules that receive a 28-bit data word plus a differential clock from an upstream parallel source. At rates up to 66 MHz, the receiver provides a compact way to transfer wide video-related data through low-voltage differential signaling instead of exposing many single-ended traces over longer routes. The recovered receiver clock supports a 50% output duty cycle for downstream clocking considerations. Designers should use the data-strobe protocol correctly, account for receiver propagation delay, and verify setup and hold timing at the destination device. Differential routing must also maintain a continuous return path to avoid converting common-mode noise into timing errors.

📱

Display Controller Interconnects

The DS90CR286AMTDX can be used in display-controller assemblies that distribute 28-bit parallel data and a clock over a compact LVDS connection. Its 66 MHz maximum clock supports demanding data-transfer periods while the separate Channel Link clock architecture avoids relying on embedded clocking in each data word. This arrangement can simplify an existing parallel-video architecture without changing the higher-level data format. The receiver should be paired with the appropriate transmitter, connector, and termination arrangement, and the PCB must preserve differential-pair symmetry. Before implementation, confirm that output voltage levels, timing margins, connector lane assignment, and power sequencing satisfy the display subsystem's requirements.

🖥️

Printer and Imaging Equipment

The DS90CR286AMTDX is suitable for printer, scanner, and imaging subsystems that carry a broad parallel payload between control electronics and an imaging engine. The 28-bit width accommodates substantial command, raster, or status data, while the 3.3 V LVDS receiver limits interface amplitude compared with a conventional single-ended bus. Operating the data strobe at up to 66 MHz can reduce the number of high-speed traces crossing internal board sections. For reliable integration, place the receiver close to the connector or source circuitry, maintain symmetric differential routing, and confirm that the transmitter's bias and termination values match the complete link. Signal simulation should include connector reflections and receiver-output timing.

🔧

Industrial Control and Data Acquisition

The DS90CR286AMTDX can receive a 28-bit data-strobe stream in industrial control and data-acquisition equipment where a legacy or deterministic parallel architecture is being connected with LVDS. Its 20 MHz-to-66 MHz operating range covers the manufacturer's stated transfer domain, and TIA/EIA-644-compatible differential signaling can improve noise immunity over longer internal cable or board routes. The receiver's less-than-270-mW power figure is useful when managing thermal budget in compact control assemblies. Designers must still isolate it from motors, relays, and switching converters, provide clean 3.3 V power, and verify that grounding and cable return arrangements satisfy common-mode limits. The family-level automotive Grade 3 option should not be confused with automotive qualification of the complete control system.

🎥

Security and Surveillance Equipment

The DS90CR286AMTDX is applicable in surveillance equipment that transfers a 28-bit parallel image or control payload between dedicated boards. Differential data-strobe signaling can reduce noise pickup when the receiver is separated from camera or processing electronics by a cable or connector. The receiver's 66 MHz maximum clock and rising-edge transfer mode support high-throughput parallel transfers, while its 3.3 V operation aligns with many compact digital subsystems. Layout quality remains critical: keep differential traces closely coupled, provide a continuous reference plane, avoid stubs, and confirm the connector and cable support the intended data rate. The system should also validate recovery behavior across power-up, reset, and cable-disconnection states before relying on the receiver for surveillance-video traffic.

Récapitulatif des produits recommandés

DS90CR286A Family reference for the 28-bit 66 MHz LVDS receiver Utilisé dans : Industrial Machine-Vision Systems, Digital Video Processing, Industrial Control and Data Acquisition SN75LVDS82DGGG4 Related Texas Instruments 56-pin LVDS interface family device Utilisé dans : Industrial Machine-Vision Systems DS90CR286 Related 28-bit 66 MHz LVDS data-strobe interface family Utilisé dans : Digital Video Processing, Printer and Imaging Equipment, Security and Surveillance Equipment DS90CR286MTD Texas Instruments Utilisé dans : Display Controller Interconnects, Industrial Control and Data Acquisition DS90CR286AMTD/NOPB Related no-lead-finish receiver ordering option Utilisé dans : Display Controller Interconnects, Security and Surveillance Equipment DS90CR286AMTDX/NOPB Related no-lead-finish ordering configuration Utilisé dans : Printer and Imaging Equipment
What is the DS90CR286AMTDX?
The DS90CR286AMTDX is a Texas Instruments 3.3 V rising-edge data-strobe LVDS receiver for 28-bit Channel Link transfers. It operates at up to 66 MHz and is packaged in a 56-pin DGG TSSOP. According to the Texas Instruments DS90CR286A product page, the family supports 20 MHz to 66 MHz shift-clock operation, a 50% receiver-output-clock duty cycle, and compatibility with TIA/EIA-644 LVDS signaling.
What is the DS90CR286AMTDX pinout and package?
The DS90CR286AMTDX uses the 56-pin DGG TSSOP package, with 48-pin or 56-pin low-profile DGG options identified for the DS90CR286A family. Use the manufacturer datasheet pin-description and connection diagrams when assigning PCB tracks, especially for differential data and clock inputs. The requested package-diagram library does not contain a 56-pin TSSOP key, so this page uses the generic package drawing rather than presenting a potentially incorrect numbered pin map.
Where can I download the DS90CR286AMTDX datasheet PDF?
The official DS90CR286A product page is the primary starting point for the DS90CR286AMTDX datasheet, ordering information, and support documents. It identifies the device as a 3.3 V, 28-bit Channel Link receiver operating to 66 MHz. Texas Instruments also lists the exact DS90CR286AMTD/NOPB orderable configuration in its part-details section, which is useful when comparing the target ordering code with the no-lead-finish designation.
What is the maximum clock frequency of DS90CR286AMTDX?
The DS90CR286AMTDX supports a maximum shift-clock frequency of 66 MHz. The manufacturer describes operation across a 20 MHz to 66 MHz range, with rising-edge data transfer and a 50% duty cycle on the receiver output clock. Your interconnect must also meet the timing and signal-integrity requirements of the associated parallel bus rather than treating 66 MHz as the only design criterion.
What is the operating temperature range of DS90CR286AMTDX?
The DS90CR286AMTDX is specified for operation from -40°C to 85°C. According to the Texas Instruments DS90CR286A product page, the DS90CR286AMTD/NOPB configuration is listed in a 56-pin DGG TSSOP with that temperature range. Confirm the exact orderable suffix when purchasing because lead-free, packaging, and automotive-grade ordering options can use different MPN endings.
Is DS90CR286AMTDX compatible with TIA/EIA-644 LVDS?
Yes, the DS90CR286AMTDX is compatible with TIA/EIA-644 LVDS signaling. The manufacturer identifies this standard alongside the device's 3.3 V operation, 20 MHz to 66 MHz clock range, and low-power receiver implementation. LVDS is a differential, low-voltage interface that is commonly used to carry high-speed parallel data and a separate clock across a compact board-level or cable connection.
Where to buy DS90CR286AMTDX online?
Use the Request a Quote form on this page to request DS90CR286AMTDX availability, current pricing, and lead time. The target is listed as a 56-TSSOP interface IC, and its ordering code should be matched carefully with the required tube or reel configuration. Submit the exact MPN DS90CR286AMTDX on the form so the returned quotation applies to the correct Texas Instruments device.
What is the price of DS90CR286AMTDX?
Current DS90CR286AMTDX pricing is obtained through the Request a Quote form on this page. The visible structured pricing fields are refreshed from current channel information rather than from an old catalog amount. For comparison, the exact suffix, package, quantity, and delivery requirements should accompany the request because changes in the no-lead-finish or shipping designation can alter availability and commercial terms.
What is the lead time for DS90CR286AMTDX?
The current lead time for DS90CR286AMTDX should be requested through the Request a Quote form on this page. Lead time can depend on exact orderable suffix, quantity, tube or reel packaging, and factory scheduling. The target designation refers to a 56-TSSOP device, so include any required DGG packaging details in the request to avoid ambiguity when the quotation is prepared.
Is DS90CR286AMTDX in stock?
Request current DS90CR286AMTDX stock status through the Request a Quote form on this page. Because the part is distributed under several closely related ordering designations, provide the complete MPN and required package quantity with the inquiry. The form is the appropriate route for confirming stock, scheduled delivery, and any minimum-order constraints for the exact configuration.
DS90CR286AMTDX vs DS90CR286MTD — which is better?
Choose the ordering option that exactly satisfies your PCB footprint, temperature, lead-free, and packaging requirements. The comparison information identifies DS90CR286MTD and DS90CR286AMTDX/NOPB as related 56-pin, 3 V receiver designs, but it also indicates that circuit details should be checked before substitution. For a new design, the DS90CR286AMTDX designation should be reconciled directly with the Texas Instruments ordering table.
What is the difference between DS90CR286AMTDX and DS90CR286AMTD/NOPB?
The principal documented distinction is the ordering designation: the Texas Instruments part-details page lists DS90CR286AMTD/NOPB, while the target is identified as DS90CR286AMTDX. Both are associated with the 3.3 V, 28-bit, 66 MHz LVDS receiver family and a 56-pin DGG TSSOP. Verify the complete ordering table for finish, reel or tube, and marking details before treating one suffix as interchangeable with the other.
When should I choose DS90CR286AMTDX over another LVDS receiver?
Choose DS90CR286AMTDX when the design specifically uses a 28-bit rising-edge data-strobe Channel Link link at 3.3 V and up to 66 MHz and can use the 56-pin DGG TSSOP interface. Select another receiver only after confirming channel count, clocking method, pin assignment, supply level, timing, and connector requirements all match; a shared TSSOP outline alone does not establish pin compatibility.
Is DS90CR286AMTDX suitable for industrial and machine-vision systems?
The DS90CR286AMTDX is suitable for industrial and machine-vision interfaces when the system uses its specific 28-bit Channel Link architecture and specified operating range. The manufacturer identifies display, printer, machine-vision, and digital-video applications for this interface family. The board still needs correct differential routing, controlled return paths, suitable terminations, and timing margin against the receiving logic.
What can replace DS90CR286AMTDX?
The closest documented replacement candidate is DS90CR286AMTDX/NOPB because it denotes the no-lead-finish configuration of the same 56-pin receiver ordering family. Other related 56-pin designations require configuration review. A valid drop-in replacement must match the DGG footprint, all 56 electrical connections, 3.3 V supply, 28-bit data-strobe protocol, clock range, and receiver timing; package similarity alone is not sufficient.
What are the key specifications of DS90CR286AMTDX that engineers should know?
The key DS90CR286AMTDX specifications are a 3.3 V supply, 28-bit Channel Link receiver operation, a 20 MHz to 66 MHz clock range, rising-edge data transfer, a 50% receiver-output-clock duty cycle, and a -40°C to 85°C operating range. Texas Instruments identifies TIA/EIA-644 compatibility, less than 270 mW receiver power consumption, and 56-pin DGG TSSOP packaging. The exact suffix and automotive qualification must be checked in the ordering table.
Is DS90CR286AMTDX suitable for display and video interfaces?
The DS90CR286AMTDX can support suitable display and video equipment when the source uses a compatible 28-bit rising-edge data-strobe LVDS interface. Its 66 MHz maximum clock and separate clock channel support wide parallel transfers, but the receiver is not a general-purpose LVDS display interface for every connector or video timing standard. Confirm channel mapping, electrical timing, cable length, and connector pinout before integration.

Données de référence d'ingénierie pour DS90CR286AMTDX — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose DS90CR286AMTDX for a new design that requires a 3.3 V, 28-bit rising-edge data-strobe LVDS link operating from 20 MHz to 66 MHz and a 56-pin DGG TSSOP footprint. DS90CR286AMTDX/NOPB is the preferred procurement comparison when the no-lead-finish designation is acceptable, while DS90CR286AMTD/NOPB and DS90CR286AMTD are related ordering configurations whose finish, marking, and packaging must be checked against the orderable table. Consider DS90CR286MTD only after confirming its circuit details, clock limits, temperature rating, and electrical pin assignments against the target. Do not choose a receiver solely by package outline: channel count, data-strobe protocol, differential input mapping, output timing, termination, and connector assignments must all match. For automotive systems, confirm whether the required AEC-Q100 Grade 3 ordering option is needed rather than assuming that the complete DS90CR286A family qualification applies to every suffix.

Comparaison avec les alternatives

Paramètre Ce produit DS90CR286AMTDX/NOPB DS90CR286AMTD/NOPB DS90CR286MTD DS90CR286AMTD
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 56-pin DGG TSSOP 56-pin DGG TSSOP 56-pin DGG TSSOP 56-pin TSSOP 56-pin TSSOP
Function 28-bit rising-edge data-strobe LVDS receiver 28-bit rising-edge data-strobe LVDS receiver 28-bit rising-edge data-strobe LVDS receiver 28-bit LVDS receiver 28-bit LVDS receiver
Supply Voltage 3.3 V 3.3 V 3.3 V 3 V 3.3 V

Principaux différenciateurs

  • Exact 56-pin DGG family configuration with documented 28-bit Channel Link operation (vs DS90CR286MTD)
  • No-lead-finish ordering alternative is available for exact procurement flexibility (vs DS90CR286AMTDX/NOPB)
  • Family-level support for TIA/EIA-644 signaling and 20 MHz-to-66 MHz operation (vs DS90CR286AMTD)

Notes de conception

Route each LVDS data or clock pair as a tightly coupled differential pair with a continuous reference plane. Keep the pair length matched, avoid test-pad stubs, and do not route over plane splits. The clock pair deserves the same geometry discipline as the 28 data pairs because timing margin can be lost through skew even when the receiver is operating below its 66 MHz maximum. Observe the manufacturer layout recommendations for connector escape geometry and via placement.

Confirm the transmitter's LVDS bias, termination, and AC-coupling arrangement before powering the receiver. Termination and bias belong to the complete Channel Link and should not be duplicated without calculating the resulting divider and load. Check receiver output setup and hold timing against the destination device at the actual shift rate. Because the family supports 20 MHz to 66 MHz operation, timing validation must cover the slowest required operating condition as well as the maximum frequency.

Provide a stable 3.3 V rail and place the receiver's local decoupling capacitors close to the supply and ground pins. Although the manufacturer reports less than 270 mW receiver power consumption for the family, the complete link also includes transmitter, termination, protection, and connector power. Measure supply noise and ground bounce at the receiver rather than inferring interface integrity from the receiver's power figure alone.

Do not substitute a receiver solely because it has a 56-pin TSSOP outline. Verify electrical pin assignment, differential data-channel count, clock polarity, receiver propagation delay, output timing, supply requirements, and connector mapping. The related ordering designations DS90CR286AMTDX/NOPB, DS90CR286AMTD/NOPB, DS90CR286MTD, and DS90CR286AMTD require configuration review for finish, marking, package form, and any functional or circuit differences.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

Texas Instruments identifies an AEC-Q100 Grade 3 option in the DS90CR286A family, but the exact ordering suffix must be confirmed for the target configuration. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for DS90CR286AMTDX were not established.

Recherches associées

ds90cr286amtdx nopb DS90CR286AMTDX datasheet DS90CR286AMTDX datasheet pdf DS90CR286AMTDX pinout DS90CR286AMTDX equivalent DS90CR286AMTDX replacement DS90CR286AMTDX cross reference DS90CR286AMTDX vs DS90CR286MTD DS90CR286AMTDX price DS90CR286AMTDX stock Texas Instruments DS90CR286AMTDX DS90CR286AMTDX 56-TSSOP DS90CR286AMTDX application circuit

Composants & termes associés

Texas Instruments DS90CR286AMTDX DS90CR286AMTDX/NOPB DS90CR286AMTD/NOPB DS90CR286MTD DS90CR286AMTD DS90CR286A DS90CR286 SN75LVDS82DGGG4 LVDS Low-Voltage Differential Signaling TIA/EIA-644 Channel Link data-strobe receiver interface IC signal transceiver semiconductor DGG TSSOP surface mount AEC-Q100 AEC-Q100 Grade 3 machine vision digital video rising-edge transfer
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ