DS90CR286AMTDX - 28-Bit LVDS Receiver | Texas Instruments
MPN: DS90CR286AMTDX ✓ AktifDS90CR286AMTDX Ringkasan
An LVDS receiver is an interface circuit that converts low-voltage differential signaling into a logic-level output. It belongs to the signal-chain hierarchy of transceiver ICs, interface ICs, and semiconductors. LVDS, or Low-Voltage Differential Signaling, provides a noise-resistant method for transferring high-speed data across a cable or PCB link while using low signal amplitudes. The DS90CR286A family is intended for parallel-to-serial data-strobe connections between processors, controllers, displays, imaging equipment, and other digital systems.
The receiver accepts eight LVDS data channels plus a differential clock, reconstructs the parallel data at the receiver, and supplies a data-strobe clock output. Its 20 MHz to 66 MHz shift-clock support and 50% receiver-output-clock duty cycle are important for systems that transfer wide parallel data over a compact differential link. The manufacturer also identifies compatibility with the TIA/EIA-644 LVDS standard, low-profile 56-pin or 48-pin DGG TSSOP options, and an automotive-qualified Grade 3 option within the DS90CR286A family.
Channel Link is a parallel bus architecture that separates data and clock rather than relying on source-synchronous clocking. This arrangement can simplify implementation in older computing, industrial-control, display, and machine-vision systems. By carrying data and clock across balanced differential lines, the interface reduces sensitivity to common-mode noise and can support reliable transmission where a single-ended bus would be more susceptible to crosstalk and ground-offset problems.
Typical uses include industrial imaging systems, video-processing equipment, display controllers, printers, machine-vision hardware, and embedded parallel-bus interfaces. When implementing the receiver, preserve the differential pair geometry specified by the manufacturer, provide an appropriate LVDS termination and bias network at the transmitter side, and route the recovered clock and data outputs as ordinary single-ended digital signals. Keep the receiver and its decoupling capacitors close to the source impedance and observe the recommended layer-stack and return-path arrangement to minimize edge degradation.
For clock-sensitive designs, check receiver output setup and hold timing against the receiving logic rather than relying only on the 66 MHz clock limit. The automotive Grade 3 variant should be selected only when the complete system requires that qualification; the DS90CR286AMTDX ordering designation must also be checked for its exact package, temperature range, reel or tube configuration, and lead-free status before placement. This page combines family-level specifications, ordering distinctions, drop-in candidates, and interface-level design guidance to simplify component selection and PCB integration.
Pilihan pengganti yang segera untuk DS90CR286AMTDX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
DS90CR286AMTDX/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR286AMTD/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR286MTD
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DS90CR286AMTD
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90CR286AMTDX Spesifikasi
| Product Type | 28-bit LVDS data-strobe receiver |
| Tegangan Pemberi Arus | 3.3 V |
| Frekuensi Klock Maksimum | 66 MHz |
| Minimum Shift Clock Frequency | 20 MHz |
| Channel Width | 28 bits |
| Signaling Standard | TIA/EIA-644 LVDS |
| Data Transfer Edge | Rising edge |
| Receiver Output Clock Duty Cycle | 50% |
| Gambaran Suhu Operasi | -40°C to 85°C |
| Kemasan | DGG TSSOP, 56 pins |
| Package Type | Low-profile TSSOP |
| Automotive Qualification | AEC-Q100 Grade 3 option available in DS90CR286A family |
| Receiver Power Consumption | <270 mW |
| Output Timing | Best-in-class set and hold times on receiver outputs; exact values require datasheet review |
| Kiraan Pin | 56 pins |
Panduan Konfigurasi Pin DS90CR286AMTDX low-profile tssop
Konfigurasi pin untuk DS90CR286AMTDX (low-profile tssop pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DS90CR286AMTDX.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DS90CR286AMTDX patut untuk 6 aplikasis: Industrial Machine-Vision Systems, Digital Video Processing, Display Controller Interconnects, Printer and Imaging Equipment, Industrial Control and Data Acquisition, Security and Surveillance Equipment.
Industrial Machine-Vision Systems
The DS90CR286AMTDX fits industrial machine-vision controllers that transfer a 28-bit parallel payload and a separate clock over an LVDS Channel Link. Its 3.3 V supply, 20 MHz-to-66 MHz clock range, and rising-edge data-strobe operation provide a defined interface for camera or image-processing subsystems. The differential receiver helps reduce susceptibility to common-mode disturbance encountered in industrial environments. Board implementation should preserve controlled differential geometry, provide the manufacturer-specified termination and bias network, and validate receiver output timing against the downstream image processor. The -40°C-to-85°C range supports equipment operating across typical industrial temperature conditions, although final enclosure temperature and system qualification remain separate design requirements.
Disebarkan
Digital Video Processing
The DS90CR286AMTDX is appropriate for digital video modules that receive a 28-bit data word plus a differential clock from an upstream parallel source. At rates up to 66 MHz, the receiver provides a compact way to transfer wide video-related data through low-voltage differential signaling instead of exposing many single-ended traces over longer routes. The recovered receiver clock supports a 50% output duty cycle for downstream clocking considerations. Designers should use the data-strobe protocol correctly, account for receiver propagation delay, and verify setup and hold timing at the destination device. Differential routing must also maintain a continuous return path to avoid converting common-mode noise into timing errors.
Disebarkan
Display Controller Interconnects
The DS90CR286AMTDX can be used in display-controller assemblies that distribute 28-bit parallel data and a clock over a compact LVDS connection. Its 66 MHz maximum clock supports demanding data-transfer periods while the separate Channel Link clock architecture avoids relying on embedded clocking in each data word. This arrangement can simplify an existing parallel-video architecture without changing the higher-level data format. The receiver should be paired with the appropriate transmitter, connector, and termination arrangement, and the PCB must preserve differential-pair symmetry. Before implementation, confirm that output voltage levels, timing margins, connector lane assignment, and power sequencing satisfy the display subsystem's requirements.
Disebarkan
Printer and Imaging Equipment
The DS90CR286AMTDX is suitable for printer, scanner, and imaging subsystems that carry a broad parallel payload between control electronics and an imaging engine. The 28-bit width accommodates substantial command, raster, or status data, while the 3.3 V LVDS receiver limits interface amplitude compared with a conventional single-ended bus. Operating the data strobe at up to 66 MHz can reduce the number of high-speed traces crossing internal board sections. For reliable integration, place the receiver close to the connector or source circuitry, maintain symmetric differential routing, and confirm that the transmitter's bias and termination values match the complete link. Signal simulation should include connector reflections and receiver-output timing.
Disebarkan
Industrial Control and Data Acquisition
The DS90CR286AMTDX can receive a 28-bit data-strobe stream in industrial control and data-acquisition equipment where a legacy or deterministic parallel architecture is being connected with LVDS. Its 20 MHz-to-66 MHz operating range covers the manufacturer's stated transfer domain, and TIA/EIA-644-compatible differential signaling can improve noise immunity over longer internal cable or board routes. The receiver's less-than-270-mW power figure is useful when managing thermal budget in compact control assemblies. Designers must still isolate it from motors, relays, and switching converters, provide clean 3.3 V power, and verify that grounding and cable return arrangements satisfy common-mode limits. The family-level automotive Grade 3 option should not be confused with automotive qualification of the complete control system.
Disebarkan
Security and Surveillance Equipment
The DS90CR286AMTDX is applicable in surveillance equipment that transfers a 28-bit parallel image or control payload between dedicated boards. Differential data-strobe signaling can reduce noise pickup when the receiver is separated from camera or processing electronics by a cable or connector. The receiver's 66 MHz maximum clock and rising-edge transfer mode support high-throughput parallel transfers, while its 3.3 V operation aligns with many compact digital subsystems. Layout quality remains critical: keep differential traces closely coupled, provide a continuous reference plane, avoid stubs, and confirm the connector and cable support the intended data rate. The system should also validate recovery behavior across power-up, reset, and cable-disconnection states before relying on the receiver for surveillance-video traffic.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DS90CR286AMTDX — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DS90CR286AMTDX/NOPB | DS90CR286AMTD/NOPB | DS90CR286MTD | DS90CR286AMTD |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-pin DGG TSSOP | 56-pin DGG TSSOP | 56-pin DGG TSSOP | 56-pin TSSOP | 56-pin TSSOP |
| Function | 28-bit rising-edge data-strobe LVDS receiver | 28-bit rising-edge data-strobe LVDS receiver | 28-bit rising-edge data-strobe LVDS receiver | 28-bit LVDS receiver | 28-bit LVDS receiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3 V | 3.3 V |
Penyeberangsung Jelas
- Exact 56-pin DGG family configuration with documented 28-bit Channel Link operation (vsDS90CR286MTD)
- No-lead-finish ordering alternative is available for exact procurement flexibility (vsDS90CR286AMTDX/NOPB)
- Family-level support for TIA/EIA-644 signaling and 20 MHz-to-66 MHz operation (vsDS90CR286AMTD)
Catatan Desain
Route each LVDS data or clock pair as a tightly coupled differential pair with a continuous reference plane. Keep the pair length matched, avoid test-pad stubs, and do not route over plane splits. The clock pair deserves the same geometry discipline as the 28 data pairs because timing margin can be lost through skew even when the receiver is operating below its 66 MHz maximum. Observe the manufacturer layout recommendations for connector escape geometry and via placement.
Confirm the transmitter's LVDS bias, termination, and AC-coupling arrangement before powering the receiver. Termination and bias belong to the complete Channel Link and should not be duplicated without calculating the resulting divider and load. Check receiver output setup and hold timing against the destination device at the actual shift rate. Because the family supports 20 MHz to 66 MHz operation, timing validation must cover the slowest required operating condition as well as the maximum frequency.
Provide a stable 3.3 V rail and place the receiver's local decoupling capacitors close to the supply and ground pins. Although the manufacturer reports less than 270 mW receiver power consumption for the family, the complete link also includes transmitter, termination, protection, and connector power. Measure supply noise and ground bounce at the receiver rather than inferring interface integrity from the receiver's power figure alone.
Do not substitute a receiver solely because it has a 56-pin TSSOP outline. Verify electrical pin assignment, differential data-channel count, clock polarity, receiver propagation delay, output timing, supply requirements, and connector mapping. The related ordering designations DS90CR286AMTDX/NOPB, DS90CR286AMTD/NOPB, DS90CR286MTD, and DS90CR286AMTD require configuration review for finish, marking, package form, and any functional or circuit differences.
Maklumat Kesediaan
Texas Instruments identifies an AEC-Q100 Grade 3 option in the DS90CR286A family, but the exact ordering suffix must be confirmed for the target configuration. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for DS90CR286AMTDX were not established.