DSPIC30F4013T-30I/PT - 16-bit DSC, 48KB Flash, 30MIPS | Microchip
Référence : DSPIC30F4013T-30I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.72 | $14,72 |
| 10 | $13.28 | $132,80 |
| 100 | $11.85 | $1 185,00 |
| 500 | $10.42 | $5 210,00 |
| 1 000 | $9.18 | $9 180,00 |
DSPIC30F4013T-30I/PT Présentation
A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and peripheral set of a microcontroller with the mathematical throughput of a DSP. The dsPIC30F4013 belongs to the DSC family within the broader category of embedded microcontrollers, sitting hierarchically between 8-bit PIC MCUs and 32-bit dsPIC33/PIC32 devices. Its modified Harvard architecture provides separate program and data buses with a 24-bit wide instruction word, enabling single-cycle MAC operations.
Key features include a 16-bit data path with DSP engine, six 16-bit timers, six PWM channels (three pairs) ideal for 3-phase motor control, a 10-bit ADC with up to 13 input channels and 200 ksps conversion rate, two UART modules, one SPI port, one I2C port, a CAN 2.0B module, and a QEI (Quadrature Encoder Interface) for position feedback. The device operates from 2.5V to 5.5V and integrates a 4x phase-locked loop.
The DSP engine includes a 40-bit wide accumulator with optional saturation logic, a 17-bit x 17-bit multiplier, and dual 40-bit saturating working registers. Barrel shifter and DO/REPEAT hardware loops accelerate filter and transform math. The single-cycle MAC at 30 MIPS gives an aggregate 60 MMACs/s, sufficient for field-oriented control of PMSM and BLDC motors.
Typical applications include 3-phase brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) drives, sensorless motor control using BEMF or flux estimation, uninterruptible power supplies, digital UPS front-end PFC stages, solar microinverters, and industrial automation servo loops. The integrated CAN and QEI peripherals make it well suited to networked industrial equipment.
When designing with this device, ensure the MCLR reset circuit uses a proper RC network and that the on-chip LDO regulator is bypassed with the recommended capacitor combination. For motor control applications, place the device's PWM outputs close to the gate drivers to minimize switching noise coupling back into the analog ADC inputs.
This page synthesizes distributor pricing, drop-in alternatives within the same 44-pin TQFP footprint, and practical design notes not found in the manufacturer datasheet alone, helping procurement and engineering teams make faster, better-informed decisions.
Alternatives de remplacement direct pour DSPIC30F4013T-30I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC30F4013T-30I/PT (même facteur de forme et même empreinte) — différant par Package, ADC, Core Architecture, Timers, Mounting Type.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC30F4013-30I/PT
✅ Remplacement direct✓ En stock
$6.78 / unité
Voir la fiche technique →DSPIC30F4013-30E/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC30F4013-20I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$6.25 / unité
Voir la fiche technique →DSPIC30F4013-20E/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$6.84 / unité
Voir la fiche technique →DSPIC30F4012T-30I/SO
✅ Remplacement direct✓ En stock
$4.1 / unité
Voir la fiche technique →dsPIC33FJ12MC201-I/P
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC30F4013T-30I/PT Valeurs maximales et caractéristiques électriques
| Core Architecture | dsPIC30F (16-bit modified Harvard DSC) |
| Instruction Word Width | 24-bit |
| Maximum CPU Speed | 30 MIPS (15 MHz external oscillator with 4x PLL) |
| Program Flash Memory | 48 KB (16K x 24) |
| Operating Voltage Range | 2.5 V to 5.5 V |
| Plage de température de fonctionnement | -40C to +85C (industrial) |
| PWM Channels | 6 channels (3 complementary pairs) with 16-bit resolution |
| Motor Control Peripherals | QEI, 3-phase PWM, input capture |
| Communication Interfaces | 2x UART, 1x SPI, 1x I2C, 1x CAN 2.0B |
| Boîtier | 44-pin TQFP (10x10 mm) |
| Type de montage | Surface Mount |
| Packaging | Tape & Reel |
| Statut RoHS | Compliant |
Guide de configuration des broches du DSPIC30F4013T-30I/PT 44-pin tqfp (10x10 mm)
Configuration des broches du DSPIC30F4013T-30I/PT (boîtier 44-pin tqfp (10x10 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour DSPIC30F4013T-30I/PT.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DSPIC30F4013T-30I/PT convient pour 6 applications: 3-Phase BLDC Motor Control, Field-Oriented Control (FOC) Servo Drives, Solar Microinverter Power Conversion, Uninterruptible Power Supply (UPS) Digital Control, Industrial Sensor Signal Conditioning, Automotive Body and Chassis Electronics.
3-Phase BLDC Motor Control
The DSPIC30F4013T-30I/PT is purpose-built for 3-phase brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) control. Its 6 PWM channels in 3 complementary pairs with programmable dead-time generation drive a 3-phase inverter directly, eliminating external logic. The Quadrature Encoder Interface (QEI) reads incremental encoders for rotor position at up to 30 MHz, while the 30 MIPS DSP engine runs field-oriented control (FOC) loops including Clarke/Park transforms, SVPWM modulation, and PI current controllers. With 48 KB Flash and 2 KB RAM, complex sensorless algorithms using BEMF or flux estimation fit comfortably. According to the Microchip dsPIC30F4013 datasheet, the 16-bit PWM offers 1.04 ns resolution at 30 MIPS for precise duty-cycle control.
Recommandé
Field-Oriented Control (FOC) Servo Drives
The DSPIC30F4013T-30I/PT delivers 30 MIPS with hardware MAC and barrel shifter, ideal for industrial servo drives implementing field-oriented control. Its DSP engine executes Clarke/Park transforms and inverse transforms at single-cycle latency, and the DO/REPEAT hardware loops accelerate sinusoidal and SVPWM look-up table generation. The CAN 2.0B module supports industrial protocols like CANopen DS402 for servo command exchange, while the 10-bit ADC samples phase currents with simultaneous triggering. According to Microchip application note AN1078, this DSC runs a complete sensorless FOC loop for PMSM motors in under 25us at 30 MIPS.
Recommandé
Solar Microinverter Power Conversion
The DSPIC30F4013T-30I/PT is widely deployed in solar microinverter designs for residential photovoltaic systems. Its 30 MIPS DSP performance runs maximum power point tracking (MPPT) algorithms on Perturb & Observe or Incremental Conductance methods, while its 6 PWM channels control the full-bridge DC-DC and DC-AC conversion stages. The 10-bit ADC samples PV panel voltage and current at 200 ksps for fast MPPT response to changing irradiance. The integrated CAN bus enables panel-level monitoring and grid-tie communication, and the 2.5V-5.5V operating range supports direct connection to 5V auxiliary rails. Microchip application note AN1339 provides a complete reference design for 250W grid-tie microinverter using this DSC.
Recommandé
Uninterruptible Power Supply (UPS) Digital Control
The DSPIC30F4013T-30I/PT provides digital control for online UPS systems up to several kVA. Its DSP engine computes real-time RMS values for input/output voltage and current, while its PWM channels drive the IGBT inverter and PFC stage. The 10-bit ADC with simultaneous sampling ensures accurate voltage regulation under step load changes, and the 30 MIPS throughput maintains total harmonic distortion (THD) under 3% for sensitive IT loads. The integrated CAN interface enables battery bank monitoring and remote management, and the wide 2.5V-5.5V supply tolerance accommodates battery voltage drops during discharge. According to Microchip AN1106, this DSC implements a complete double-conversion UPS topology with PFC in under 30us control loop latency.
Recommandé
Industrial Sensor Signal Conditioning
The DSPIC30F4013T-30I/PT integrates DSP and MCU functionality for industrial sensor signal processing applications. Its 16-bit DSP engine runs digital filters (FIR, IIR) at sample rates up to 250 kHz, conditioning signals from pressure, flow, and vibration sensors before transmission. The 10-bit ADC with 13 input channels multiplexes multiple sensor inputs, and the CAN 2.0B interface publishes processed data to industrial networks like CANopen or DeviceNet. The wide -40C to +85C operating range and 2.5V-5.5V supply tolerance make it robust for factory floor deployments. The 48 KB Flash stores complex filter coefficients and calibration tables.
Recommandé
Automotive Body and Chassis Electronics
The DSPIC30F4013T-30I/PT serves automotive body and chassis applications such as electronic power steering, active suspension, and HVAC blower control. Its CAN 2.0B module integrates directly with vehicle CAN bus networks, while its 6 PWM channels drive motors and solenoids with 16-bit resolution. The 10-bit ADC reads multiple sensor inputs for closed-loop control of actuators. Although the industrial 'I' temperature grade (-40C to +85C) is below strict automotive AEC-Q100 requirements, this DSC is widely used in non-safety-critical automotive subsystems where extended temperature is not required. According to the dsPIC30F4013 datasheet, ESD ratings on I/O pins exceed 4 kV HBM for robust automotive environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC30F4013T-30I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC30F4013-30I/PT | DSPIC30F4013-30E/PT | DSPIC30F4013-20I/PT | DSPIC30F4013-20E/PT | DSPIC30F4012T-30I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin TQFP (10x10 mm) | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 28-pin SOIC (different) |
| CPU Speed | 30 MIPS | 30 MIPS | 30 MIPS | 20 MIPS | 20 MIPS | 30 MIPS |
| Program Flash | 48 KB | 48 KB | 48 KB | 48 KB | 48 KB | 32 KB |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +125C (Extended) | -40C to +85C | -40C to +125C | -40C to +85C |
| PWM Channels | 6 (3 complementary pairs) | 6 | 6 | 6 | 6 | 4 |
| ADC | 10-bit, 13 ch, 200 ksps | 10-bit, 13 ch | 10-bit, 13 ch | 10-bit, 13 ch | 10-bit, 13 ch | 10-bit, 6 ch |
| CAN Module | Yes (CAN 2.0B) | Yes | Yes | Yes | Yes | Yes |
| Packaging Format | Tape & Reel | Tray | Tray | Tray | Tray | Tape & Reel |
Principaux différenciateurs
- Tape & Reel packaging optimized for high-volume SMD assembly (vs DSPIC30F4013-30I/PT)
- Industrial temperature grade optimized for factory floor deployment (vs DSPIC30F4013-30E/PT)
- 30 MIPS headroom over the 20 MIPS variant for advanced motor control algorithms (vs DSPIC30F4013-20I/PT)
Notes de conception
The DSPIC30F4013T-30I/PT requires proper decoupling on both AVDD and VDD pins per Microchip datasheet 70138. Place a 10uF tantalum or ceramic bulk capacitor near each VDD/AVDD pin pair, with a 0.1uF ceramic bypass capacitor placed within 5mm of each pin. The on-chip LDO regulator that supplies the 2.5V core (VDDCORE) must have its own dedicated 10uF + 0.1uF capacitor combination on the VDDCORE pin. Failure to provide adequate decoupling can cause ADC noise, oscillator drift, and intermittent code-execution failures, especially at the full 30 MIPS speed grade where current transients exceed 50 mA during PWM events.
For 3-phase motor control applications, separate the analog and digital ground planes using a single-point connection under the device's GND pin. Route the 3 PWM output pairs (PWM1H/L, PWM2H/L, PWM3H/L) as matched-length differential traces to the gate driver inputs to maintain switching symmetry. Keep the analog ADC input traces away from PWM switching nodes by at least 3mm or use a ground trace between them. According to Microchip AN1078 PCB layout guidelines, the exposed thermal pad on the TQFP package should be soldered to a copper pour connected to GND for improved thermal dissipation in motor drive applications.
Several common pitfalls occur when designing with the DSPIC30F4013T-30I/PT: (1) Configuring the PLL with incorrect multiplier or input frequency - the PLL accepts 4 MHz to 10 MHz input and multiplies by 4x, 8x, or 16x; verify the configuration bits against the actual oscillator. (2) Failing to disable the watchdog timer in software within the timeout period will cause unintended resets. (3) Using the 30 MIPS speed grade below 4.5V VDD violates the datasheet electrical specifications. (4) Configuring PWM with dead time less than 500 ns in motor drive applications can cause shoot-through in the inverter bridge.
Informations de conformité
RoHS and REACH compliant per Microchip product page and distributor listings (DigiKey, Mouser, LCSC). Not AEC-Q100 qualified - for automotive safety-critical applications use dsPIC33EV or dsPIC33CH AEC-Q100 qualified variants. Lead-free and halogen-free per Microchip environmental compliance documentation.
