DSPIC30F6014A-30I/PT - 30 MIPS 16-bit DSC, 144KB Flash, TQFP-80 | Microchip
Référence : DSPIC30F6014A-30I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.78 | $167,80 |
| 100 | $14.95 | $1 495,00 |
| 500 | $13.2 | $6 600,00 |
| 1 000 | $11.85 | $11 850,00 |
DSPIC30F6014A-30I/PT Présentation
A Digital Signal Controller is a hybrid architecture that merges a microcontroller's deterministic interrupt-driven control loop with a digital signal processor's parallel math engine, occupying the conceptual middle ground between MCU and DSP. Within the broader taxonomy, the dsPIC30F6014A sits at the IC tier, inside the Embedded Controllers branch, and is a sibling of the dsPIC33F and PIC24F device families that share peripheral IP and toolchain. It supports operation from 2.5 V to 5.5 V, enabling direct interface to 5 V analog front-ends without level shifters.
Key features include 8 KB SRAM, 4 KB EEPROM, two UART/SPI/I2C modules, two CAN 2.0B controllers, eight 16-bit timers, a 12-bit ADC with up to 16 channels and 200 ksps throughput, plus a 16-bit PWM module with up to 8 outputs and complementary mode. The dedicated DSP engine features zero-overhead looping, bit-reverse addressing, and fractional/integer math support, allowing real-time FFT and FIR/IIR filter execution without starving the control loop.
On the integration side, the device embeds an on-chip 8 MHz and 32 kHz RC oscillator, a 5-bit programmable dead-time controller, an input capture module, and a quadrature encoder interface, eliminating many external analog and timing components. The wide 2.5-5.5 V supply range combined with low standby current makes it suitable for both line-powered and battery-backed designs, while the integrated CAN bus and multiple serial interfaces reduce BOM in industrial and automotive networked systems.
Typical applications include three-phase AC induction and BLDC/PMSM motor drives, solar micro-inverters and digital power factor correction, industrial sensor signal conditioning, UPS and switch-mode power supplies, and automotive body/comfort modules requiring on-chip CAN. Industrial designers favor this part for motion control; automotive engineers select it for CAN-connected actuator nodes. Educational users adopt it for control-theory and DSP lab courses.
When designing with the DSPIC30F6014A, pay close attention to the 80-pin TQFP-12x12 (PT) footprint versus the larger 14x14 (PF) variant - both share the same silicon but differ in package body, which can affect PCB layout and clearance for high-voltage isolated designs. Use the MPLAB XC16 compiler and MPLAB X IDE for code development, and choose the motor-control or digital-power dsPIC30F peripheral libraries to shorten firmware bring-up. For new designs, evaluate migrating to the dsPIC33F or dsPIC33E family for higher MIPS and more peripherals while preserving peripheral-level code portability.
This page synthesizes distributor pricing, same-package TQFP-80 drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - including cross-reference to the 14x14 TQFP (PF) variant and migration guidance to the dsPIC33E family.
Alternatives de remplacement direct pour DSPIC30F6014A-30I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC30F6014A-30I/PT (même facteur de forme et même empreinte) — différant par Core Architecture, Operating Temperature, Package, ADC, DSP Engine.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC30F6014A-30I/PF
✅ Remplacement direct✓ En stock
$8.65 / unité
Voir la fiche technique →DSPIC30F6014A-20I/PT
✅ Remplacement direct✓ En stock
$7.65 / unité
Voir la fiche technique →DSPIC30F6014-30I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC30F6013A-30I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$10.93 / unité
Voir la fiche technique →DSPIC30F6012A-30I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC30F6011A-30I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC30F6014A-30I/PT Valeurs maximales et caractéristiques électriques
| Core Architecture | dsPIC30F 16-bit modified Harvard |
| CPU Clock Speed | 40 MHz (30 MIPS) |
| Program Memory (Flash) | 144 KB |
| Data RAM | 8 KB |
| Data EEPROM | 4 KB |
| Supply Voltage (VDD) | 2.5 V to 5.5 V |
| I/O Pins | 68 |
| ADC | 12-bit, up to 16 channels, 200 ksps |
| PWM Outputs | 8 x 16-bit (with complementary mode) |
| Timers | 8 x 16-bit |
| UART | 2 modules |
| SPI | 2 modules |
| I2C | 2 modules |
| CAN | 2 x CAN 2.0B |
| Quadrature Encoder Interface | Yes |
| Input Capture | 8 channels |
| Température de fonctionnement | -40 C to +85 C (Industrial) |
| Boîtier | TQFP-80 (PT), 12x12 mm |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
Configuration des broches de DSPIC30F6014A-30I/PT
| Broche 1 | RD12 — Remappable digital I/O / PWM4H |
| Broche 2 | RD13 — Remappable digital I/O |
| Broche 3 | AVDD — Analog supply voltage |
| Broche 4 | AVSS — Analog ground |
| Broche 5 | AN0 — Analog input 0 / VREF+ |
| Broche 6 | AN1 — Analog input 1 / VREF- |
| Broche 7 | AN2 — Analog input 2 |
| Broche 8 | AN3 — Analog input 3 |
| Broche 9 | AN4 — Analog input 4 |
| Broche 10 | AN5 — Analog input 5 |
| Broche 11 | AN6 — Analog input 6 |
| Broche 12 | AN7 — Analog input 7 |
| Broche 13 | AN8 — Analog input 8 |
| Broche 14 | AN9 — Analog input 9 |
| Broche 15 | AN10 — Analog input 10 |
| Broche 16 | AN11 — Analog input 11 |
| Broche 17 | AN12 — Analog input 12 |
| Broche 18 | AN13 — Analog input 13 |
| Broche 19 | AN14 — Analog input 14 |
| Broche 20 | AN15 — Analog input 15 |
| Broche 21 | VDD — Digital supply voltage |
| Broche 22 | VSS — Digital ground |
| Broche 23 | OSC1 — Crystal oscillator input |
| Broche 24 | OSC2 — Crystal oscillator output |
| Broche 25 | RC13 — Digital I/O |
| Broche 26 | RC14 — Digital I/O / SOSCO |
| Broche 27 | RC15 — Digital I/O / SOSCI |
| Broche 28 | FLTA — PWM fault A input |
| Broche 29 | PWM1L — PWM1 low-side output |
| Broche 30 | PWM1H — PWM1 high-side output |
| Broche 31 | PWM2L — PWM2 low-side output |
| Broche 32 | PWM2H — PWM2 high-side output |
| Broche 33 | PWM3L — PWM3 low-side output |
| Broche 34 | PWM3H — PWM3 high-side output |
| Broche 35 | PWM4L — PWM4 low-side output |
| Broche 36 | PWM4H — PWM4 high-side output |
| Broche 37 | QEA — Quadrature encoder A input |
| Broche 38 | QEB — Quadrature encoder B input |
| Broche 39 | INDX — Quadrature encoder index input |
| Broche 40 | IC1 — Input capture 1 |
| Broche 41 | IC2 — Input capture 2 |
| Broche 42 | IC3 — Input capture 3 |
| Broche 43 | IC4 — Input capture 4 |
| Broche 44 | IC5 — Input capture 5 |
| Broche 45 | IC6 — Input capture 6 |
| Broche 46 | IC7 — Input capture 7 |
| Broche 47 | IC8 — Input capture 8 |
| Broche 48 | OC1 — Output compare 1 |
| Broche 49 | OC2 — Output compare 2 |
| Broche 50 | OC3 — Output compare 3 |
| Broche 51 | OC4 — Output compare 4 |
| Broche 52 | OC5 — Output compare 5 |
| Broche 53 | OC6 — Output compare 6 |
| Broche 54 | OC7 — Output compare 7 |
| Broche 55 | OC8 — Output compare 8 |
| Broche 56 | T1CK — Timer1 external clock |
| Broche 57 | T2CK — Timer2 external clock |
| Broche 58 | T3CK — Timer3 external clock |
| Broche 59 | T4CK — Timer4 external clock |
| Broche 60 | U1RX — UART1 receive / remappable |
| Broche 61 | U1TX — UART1 transmit / remappable |
| Broche 62 | U2RX — UART2 receive |
| Broche 63 | U2TX — UART2 transmit |
| Broche 64 | SCK1 — SPI1 clock |
| Broche 65 | SDI1 — SPI1 data in |
| Broche 66 | SDO1 — SPI1 data out |
| Broche 67 | SS1 — SPI1 slave select |
| Broche 68 | SDA1 — I2C1 data |
| Broche 69 | SCL1 — I2C1 clock |
| Broche 70 | C1RX — CAN1 receive |
| Broche 71 | C1TX — CAN1 transmit |
| Broche 72 | C2RX — CAN2 receive |
| Broche 73 | C2TX — CAN2 transmit |
| Broche 74 | RD0 — Remappable digital I/O |
| Broche 75 | RD1 — Remappable digital I/O |
| Broche 76 | RD2 — Remappable digital I/O |
| Broche 77 | RD3 — Remappable digital I/O |
| Broche 78 | MCLR — Master clear / reset input |
| Broche 79 | VDD — Digital supply voltage |
| Broche 80 | VSS — Digital ground |
Applications typiques
DSPIC30F6014A-30I/PT convient pour 7 applications: Three-Phase BLDC / PMSM Motor Control, Digital Power Conversion (PFC, Solar Inverter, UPS), Industrial Sensor Signal Conditioning, Automotive Body & Comfort CAN Nodes, Switch-Mode Power Supply (SMPS) Digital Control, Audio / Voice-band DSP Front-End, Uninterruptible Power Supply (UPS) Control.
Three-Phase BLDC / PMSM Motor Control
The DSPIC30F6014A-30I/PT's 30 MIPS DSP engine and 8-channel 16-bit PWM with programmable dead-time make it ideally suited for sensorless and sensored field-oriented control of three-phase BLDC and PMSM motors. The integrated quadrature encoder interface (QEI) handles sensored rotor-position feedback, while the 12-bit 200 ksps ADC samples phase currents at the 30+ kHz rates typical of FOC loops. With 144 KB Flash the device stores complete Clarke/Park transforms, SVPWM tables, and PI controllers without external memory, and the dual CAN 2.0B ports expose the drive to industrial fieldbuses (CANopen, DeviceNet) for multi-axis machinery.
Recommandé
Digital Power Conversion (PFC, Solar Inverter, UPS)
The 30 MIPS throughput, single-cycle MAC, and high-resolution PWM let the DSPIC30F6014A-30I/PT implement totem-pole PFC, LLC resonant control, and MPPT loops for solar micro-inverters in the 1-5 kW range. The 12-bit ADC at 200 ksps samples inductor current and DC-bus voltage at the 100+ kHz switching frequencies common in modern SiC/GaN converters, while the on-chip DSP ALU runs the control law with sub-microsecond latency. Wide 2.5-5.5 V supply operation supports direct connection to 3.3 V or 5 V auxiliary rails, and the dual CAN interfaces integrate the inverter into smart-grid and battery-storage systems with minimal external logic.
Recommandé
Industrial Sensor Signal Conditioning
In factory automation, the DSPIC30F6014A-30I/PT combines DSP-class FIR/IIR filtering with deterministic MCU-class I/O to clean and linearize signals from load cells, strain gauges, flow meters, and industrial thermocouples. The 144 KB Flash accommodates multi-rate decimation filters and look-up-table linearization without external memory, while dual CAN 2.0B ports expose the calibrated reading to PLCs and SCADA networks. Operating from -40 C to +85 C with 2.5-5.5 V supply lets the same board drive both 24 V industrial sensors and 5 V analog front-ends after simple resistive dividers.
Recommandé
Automotive Body & Comfort CAN Nodes
Although not AEC-Q100 qualified, the DSPIC30F6014A-30I/PT is widely used in non-safety automotive body-electronics modules such as seat controllers, mirror adjusters, HVAC blend-door actuators, and central-locking nodes that communicate over CAN 2.0B at 125-500 kbps. The wide 2.5-5.5 V supply tolerance handles load-dump and cold-crank transients when paired with a TVS clamp, while 8 KB SRAM buffers diagnostic-trouble-code (DTC) snapshots for UDS services. Two CAN controllers allow bridge or gateway operation between powertrain and body CAN buses with firmware-controlled bit-rate switching.
Recommandé
Switch-Mode Power Supply (SMPS) Digital Control
Replacing analog PWM controllers with the DSPIC30F6014A-30I/PT enables programmable soft-start, adaptive dead-time compensation, and firmware-driven current-mode control for AC/DC and DC/DC converters from 50 W to 2 kW. The 16-bit PWM module generates switching frequencies from 1 kHz to 1 MHz with 25 ns resolution, while the 12-bit ADC samples feedback signals synchronously to the PWM carrier for cycle-by-cycle current limiting. The 144 KB Flash stores multiple firmware-configurable converter personalities (e.g., 12 V/24 V/48 V bus) and the dual UART modules support PMBus or SCPI command interfaces.
Recommandé
Audio / Voice-band DSP Front-End
For voice-band and 20 kHz audio front-ends, the DSPIC30F6014A-30I/PT's zero-overhead looping, bit-reverse addressing, and 17x17 hardware MAC execute real-time FFTs, FIR filters, and noise-cancelling algorithms at 30 MIPS without burdening the control loop. Typical use cases include hands-free intercom systems, public-address DSP front-ends, acoustic echo cancellation, and active noise control in HVAC ducts. The 12-bit ADC and PWM can also generate sigma-delta-class audio CODEC interfaces when paired with external op-amps, while dual UART ports bridge to Bluetooth or DSP-processor expansion boards for higher-bandwidth audio paths.
Recommandé
Uninterruptible Power Supply (UPS) Control
Online and line-interactive UPS systems in the 1-10 kVA range use the DSPIC30F6014A-30I/PT to run inverter control, battery management, and grid-synchronization loops in a single MCU. The 8-channel PWM drives the full-bridge IGBT inverter at 20-50 kHz with programmable dead-time, while dual CAN ports expose telemetry (battery state-of-charge, load, faults) to the system display and remote-monitoring service. Wide 2.5-5.5 V supply operation lets the controller run directly from a 3.3 V or 5 V aux rail while the 144 KB Flash stores multiple firmware personalities for 120 V/230 V/240 V grid regions selected at manufacturing time.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC30F6014A-30I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC30F6014A-30I/PF | DSPIC30F6014A-20I/PT | DSPIC30F6014-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6012A-30I/PT | DSPIC30F6011A-30I/PT |
|---|---|---|---|---|---|---|---|
| Package | TQFP-80 (PT), 12x12 mm | TQFP-80 (PF), 14x14 mm | TQFP-80 (PT), 12x12 mm - same | TQFP-80 (PT), 12x12 mm - same | TQFP-80 (PT), 12x12 mm - same | TQFP-80 (PT), 12x12 mm - same | TQFP-80 (PT), 12x12 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Clock | 40 MHz (30 MIPS) | 40 MHz (30 MIPS) | 33 MHz (20 MIPS) | 40 MHz (30 MIPS) | 40 MHz (30 MIPS) | 40 MHz (30 MIPS) | 40 MHz (30 MIPS) |
| Program Flash | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB | 132 KB |
| Data RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 6 KB | 6 KB |
| Data EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| I/O Pins | 68 | 68 | 68 | 68 | 68 | 52 | 52 |
| CAN Modules | 2 x CAN 2.0B | 2 x CAN 2.0B | 2 x CAN 2.0B | 2 x CAN 2.0B | 2 x CAN 2.0B | 2 x CAN 2.0B | 2 x CAN 2.0B |
| Supply Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principaux différenciateurs
- Highest memory configuration in the 601x family (vs DSPIC30F6012A-30I/PT)
- Faster CPU clock than the -20I variant (vs DSPIC30F6014A-20I/PT)
- Smaller PCB footprint than the -PF variant (vs DSPIC30F6014A-30I/PF)
Notes de conception
Estimated: At 40 MHz CPU clock and 30 MIPS sustained operation with all peripherals enabled, the DSPIC30F6014A-30I/PT typically draws 60-80 mA from VDD. Place a 10 uF bulk + 0.1 uF decoupling capacitor pair within 5 mm of every VDD/VSS pin pair, plus a 1 uF + 0.1 uF pair on AVDD/AVSS to keep ADC readings stable. The 2.5-5.5 V supply range means a single 3.3 V LDO can power both the MCU and 3.3 V sensors, simplifying the BOM. Decouple the PLL VDD pin with a dedicated 0.1 uF X7R capacitor to prevent jitter on the 40 MHz internal clock.
Estimated: At 3.3 V supply and 80 mA active current, the device dissipates roughly 0.26 W - well within the 80-pin TQFP's 1 W+ thermal envelope without a heatsink. The exposed thermal pad of the 12x12 mm TQFP-80 (PT) body should be soldered to a 1 sq in copper pour on the top layer and stitched with thermal vias to inner ground planes to spread heat during sustained motor-control loops where the CPU is at 100 percent utilization. For industrial applications at +85 C ambient, this keep-out zone is mandatory to keep the junction below +125 C.
Route the analog AGND/AVDD traces separately from the digital GND/VDD traces and join them at a single point beneath the IC's exposed pad to avoid ground-loop noise coupling into the ADC. Place the external 8 MHz crystal within 5 mm of OSC1/OSC2 with short, symmetrical traces and guard the traces with a ground ring to minimize EMI injection into the PLL. For CAN bus designs, keep the CANRX/CANTX traces shorter than 50 mm and add a 120 ohm termination resistor at each end of the bus to meet ISO 11898 signal-integrity requirements.
Estimated: The 12-bit ADC achieves its 200 ksps throughput with 12 ENOB only when the analog input source impedance is below 1 kohm - pair the analog channels with op-amp buffers (e.g., MCP6002) when sourcing from high-impedance sensors. For motor-control current sensing, synchronize ADC sampling to the PWM zero-crossing event to reject switching noise; Microchip application note AN1078 documents the exact register configuration. When using the CAN peripherals at 1 Mbps, ensure the CAN transceiver (e.g., MCP2551 or TLE7259) has a split-termination network to suppress common-mode ringing.
Common pitfalls: (1) Do not confuse the PT (12x12 mm) and PF (14x14 mm) TQFP-80 package suffixes - they require different PCB footprints despite the same pinout. (2) The internal 8 MHz RC oscillator has +/- 2 percent accuracy, which is unsuitable for CAN 2.0B at 500 kbps - always use an external crystal for bus timing. (3) The 30 MIPS rating assumes sequential instruction fetch from Flash; loops with frequent branches can drop to 50-70 percent of nominal MIPS - verify with the MPLAB SIM simulator before committing to firmware timing budgets.
Informations de conformité
RoHS compliant and lead-free per Microchip product page; the part is industrial temperature grade (-40 C to +85 C) and is not AEC-Q100 qualified - automotive safety-critical designs should use the dsPIC33EV-Q1 family instead.
