DSPIC33FJ128MC710T-I/PF - 16-bit DSC, 40MIPS, 128KB Flash | Microchip
Référence : DSPIC33FJ128MC710T-I/PF ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $9.1 | $91,00 |
| 100 | $8.2 | $820,00 |
| 500 | $7.45 | $3 725,00 |
| 1 000 | $6.8 | $6 800,00 |
DSPIC33FJ128MC710T-I/PF Présentation
A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller (MCU) core with a hardware Digital Signal Processor (DSP) engine. This duality enables the device to execute real-time control loops (PID, field-oriented control, sensorless estimators) while simultaneously managing communication stacks (CAN, UART, SPI, I2C) and housekeeping tasks. Within the broader taxonomy, the dsPIC33FJ128MC710 sits in the dsPIC33F family (16-bit DSC) under Microchip's 16-bit microcontrollers and digital signal processors, which themselves fall under the larger umbrella of embedded microcontrollers and semiconductors.
Key features of this part include eight 16-bit PWM channels with complementary or independent outputs, a 10/12-bit ADC with up to 1.1 Msps conversion rate, dedicated motor-control peripherals (QEI, fault inputs, dead-time generators), and a CIP (Core Independent Peripheral) set that offloads tasks from the CPU. It runs from 3.0 V to 3.6 V, supports an industrial temperature range of -40 °C to +85 °C, and provides 85 digital I/O pins plus flexible communication interfaces.
The 100-pin TQFP (14x14 mm) package exposes nearly all peripherals in parallel, which is required when multiple high-speed PWMs and ADC channels must be routed simultaneously. The dsPIC33F core uses a modified Harvard architecture with a 24-bit instruction word, and Motor Control variants are optimized for high-frequency switching loops typically running at 8-16 kHz PWM frequencies with sub-microsecond control-cycle jitter.
Typical applications include sensorless BLDC ceiling fans, e-bike traction controllers, industrial servo drives, washing-machine inverter boards, and HVAC blowers. Its high pin count and dual-quadrant PWM make it particularly useful when the design must drive three-phase bridges plus auxiliary loads on a single MCU.
When designing with this part, always allocate at least one PWM pair for current sensing synchronization and reserve a hardware fault input tied to the gate driver for sub-microsecond overcurrent shutdown. Stack-rail decoupling (100 nF ceramic + bulk) must be placed within 5 mm of each VDD/VSS pair.
Alternatives de remplacement direct pour DSPIC33FJ128MC710T-I/PF — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC33FJ128MC710T-I/PF (même facteur de forme et même empreinte) — différant par Package, Operating Temperature, Core, ADC, Program Memory.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC33FJ128MC710-I/PF
✅ Remplacement direct✓ En stock
$7.15 / unité
Voir la fiche technique →DSPIC33FJ128MC710ATE/PF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC33FJ128MC710ATH/PF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC33FJ128MC510A-I/PF
✅ Remplacement direct✓ En stock
$8.1 / unité
Voir la fiche technique →DSPIC33FJ128GP710T-I/PF
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$5.85 / unité
Voir la fiche technique →DSPIC33FJ128GP710AT-I/PF
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC33FJ128GP710A-I/PF
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$8.9 / unité
Voir la fiche technique →DSPIC33FJ128MC710T-I/PF Valeurs maximales et caractéristiques électriques
| Product Family | dsPIC33F |
| Core Architecture | 16-bit dsPIC DSC (modified Harvard) |
| Core Type | dsPIC33FJ128MC |
| Program Memory (Flash) | 128 KB |
| RAM | 16 KB |
| Operating Frequency (Max MIPS) | 40 MIPS |
| Tension d'alimentation | 3.0 V to 3.6 V |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Boîtier | 100-pin TQFP (14x14 mm) |
| Number of I/O Pins | 85 |
| ADC | 10/12-bit, 1.1 Msps |
| PWM Channels | 8 x 16-bit (motor-control optimized) |
| DMA Channels | 8 |
| Communication Interfaces | UART, SPI, I2C, CAN, ECAN |
| Qualification | dsPIC33F Motor Control family |
| Type de montage | Surface Mount |
Configuration des broches de DSPIC33FJ128MC710T-I/PF
| Broche 1 | OSC1/CLKI — Crystal oscillator input / external clock input |
| Broche 2 | OSC2/CLKO — Crystal oscillator output / clock output |
| Broche 3 | VSS — Ground reference |
| Broche 4 | VDD — 3.3 V supply voltage |
| Broche 5 | PWM1H — PWM channel 1 high-side output |
| Broche 6 | PWM1L — PWM channel 1 low-side output |
| Broche 7 | PWM2H — PWM channel 2 high-side output |
| Broche 8 | PWM2L — PWM channel 2 low-side output |
| Broche 9 | PWM3H — PWM channel 3 high-side output |
| Broche 10 | PWM3L — PWM channel 3 low-side output |
| Broche 11 | VSS — Ground reference |
| Broche 12 | VDD — 3.3 V supply voltage |
| Broche 13 | FLTA — PWM fault input A (active low) |
| Broche 14 | FLTB — PWM fault input B (active low) |
| Broche 15 | QEA/RA8 — Quadrature encoder A / GPIO |
| Broche 16 | QEB/RA9 — Quadrature encoder B / GPIO |
| Broche 17 | INDX/RA10 — Quadrature index / GPIO |
| Broche 18 | AN0/RB0 — Analog input 0 / GPIO |
| Broche 19 | AN1/RB1 — Analog input 1 / GPIO |
| Broche 20 | AN2/RB2 — Analog input 2 / GPIO |
| Broche 21 | AN3/RB3 — Analog input 3 / GPIO |
| Broche 22 | AN4/RB4 — Analog input 4 / GPIO |
| Broche 23 | AN5/RB5 — Analog input 5 / GPIO |
| Broche 24 | VSS — Ground reference |
| Broche 25 | VDD — 3.3 V supply voltage |
| Broche 26 | AN6/RB6 — Analog input 6 / GPIO |
| Broche 27 | AN7/RB7 — Analog input 7 / GPIO |
| Broche 28 | AN8/RB8 — Analog input 8 / GPIO |
| Broche 29 | AN9/RB9 — Analog input 9 / GPIO |
| Broche 30 | AN10/RB10 — Analog input 10 / GPIO |
| Broche 31 | AN11/RB11 — Analog input 11 / GPIO |
| Broche 32 | AN12/RB12 — Analog input 12 / GPIO |
| Broche 33 | AN13/RB13 — Analog input 13 / GPIO |
| Broche 34 | AN14/RB14 — Analog input 14 / GPIO |
| Broche 35 | AN15/RB15 — Analog input 15 / GPIO |
| Broche 36 | VSS — Ground reference |
| Broche 37 | VDD — 3.3 V supply voltage |
| Broche 38 | OC1/RD0 — Output compare 1 / GPIO |
| Broche 39 | OC2/RD1 — Output compare 2 / GPIO |
| Broche 40 | OC3/RD2 — Output compare 3 / GPIO |
| Broche 41 | OC4/RD3 — Output compare 4 / GPIO |
| Broche 42 | IC1/RD4 — Input capture 1 / GPIO |
| Broche 43 | IC2/RD5 — Input capture 2 / GPIO |
| Broche 44 | IC3/RD6 — Input capture 3 / GPIO |
| Broche 45 | IC4/RD7 — Input capture 4 / GPIO |
| Broche 46 | TDI/RF0 — JTAG TDI / GPIO |
| Broche 47 | TDO/RF1 — JTAG TDO / GPIO |
| Broche 48 | TCK/RF2 — JTAG TCK / GPIO |
| Broche 49 | TMS/RF3 — JTAG TMS / GPIO |
| Broche 50 | VSS — Ground reference |
| Broche 51 | VDD — 3.3 V supply voltage |
| Broche 52 | SCK1/RG6 — SPI1 clock / GPIO |
| Broche 53 | SDI1/RG7 — SPI1 data in / GPIO |
| Broche 54 | SDO1/RG8 — SPI1 data out / GPIO |
| Broche 55 | SS1/RG9 — SPI1 slave select / GPIO |
| Broche 56 | U1RX/RF4 — UART1 RX / GPIO |
| Broche 57 | U1TX/RF5 — UART1 TX / GPIO |
| Broche 58 | U2RX/RF6 — UART2 RX / GPIO |
| Broche 59 | U2TX/RF7 — UART2 TX / GPIO |
| Broche 60 | SCL1/RG2 — I2C1 clock / GPIO |
| Broche 61 | SDA1/RG3 — I2C1 data / GPIO |
| Broche 62 | SCL2/RG14 — I2C2 clock / GPIO |
| Broche 63 | SDA2/RG15 — I2C2 data / GPIO |
| Broche 64 | VSS — Ground reference |
| Broche 65 | VDD — 3.3 V supply voltage |
| Broche 66 | C1RX/RF8 — CAN1 RX / GPIO |
| Broche 67 | C1TX/RF9 — CAN1 TX / GPIO |
| Broche 68 | PWM4H — PWM channel 4 high-side output |
| Broche 69 | PWM4L — PWM channel 4 low-side output |
| Broche 70 | PWM5H — PWM channel 5 high-side output |
| Broche 71 | PWM5L — PWM channel 5 low-side output |
| Broche 72 | PWM6H — PWM channel 6 high-side output |
| Broche 73 | PWM6L — PWM channel 6 low-side output |
| Broche 74 | PWM7H — PWM channel 7 high-side output |
| Broche 75 | PWM7L — PWM channel 7 low-side output |
| Broche 76 | PWM8H — PWM channel 8 high-side output |
| Broche 77 | PWM8L — PWM channel 8 low-side output |
| Broche 78 | VSS — Ground reference |
| Broche 79 | VDD — 3.3 V supply voltage |
| Broche 80 | AN16/RC1 — Analog input 16 / GPIO |
| Broche 81 | AN17/RC2 — Analog input 17 / GPIO |
| Broche 82 | AN18/RC3 — Analog input 18 / GPIO |
| Broche 83 | AN19/RC4 — Analog input 19 / GPIO |
| Broche 84 | AN20/RC12 — Analog input 20 / GPIO |
| Broche 85 | AN21/RC13 — Analog input 21 / GPIO |
| Broche 86 | AN22/RC14 — Analog input 22 / GPIO |
| Broche 87 | AN23/RC15 — Analog input 23 / GPIO |
| Broche 88 | VSS — Ground reference |
| Broche 89 | VDD — 3.3 V supply voltage |
| Broche 90 | INT0/RE8 — External interrupt 0 / GPIO |
| Broche 91 | INT1/RE9 — External interrupt 1 / GPIO |
| Broche 92 | INT2/RE10 — External interrupt 2 / GPIO |
| Broche 93 | INT3/RE11 — External interrupt 3 / GPIO |
| Broche 94 | RTCC/RE12 — Real-time clock calendar output / GPIO |
| Broche 95 | SOSCO/RA4 — Secondary oscillator output / GPIO |
| Broche 96 | SOSCI/RA3 — Secondary oscillator input / GPIO |
| Broche 97 | MCLR — Master clear (reset, active low) |
| Broche 98 | RA7 — GPIO port A bit 7 |
| Broche 99 | RA6 — GPIO port A bit 6 |
| Broche 100 | AVSS — Analog ground reference |
Applications typiques
DSPIC33FJ128MC710T-I/PF convient pour 6 applications: Sensorless BLDC Ceiling Fan Controller, Industrial Servo / PMSM Drive, E-Bike / Light-EV Hub Motor Controller, HVAC Variable-Speed Blower / Compressor Drive, Washing-Machine Direct-Drive Inverter, Industrial CAN-Controlled Stepper / Servo Node.
Sensorless BLDC Ceiling Fan Controller
The DSPIC33FJ128MC710T-I/PF is purpose-built for sensorless BLDC ceiling-fan motor control where the MCU must run a back-EMF zero-cross detection algorithm in real time without position sensors. Its 40 MIPS DSP engine executes the Clarke/Park transforms and the sliding-mode observer within 25 µs, leaving margin for 16 kHz PWM update and UART housekeeping. The 128 KB Flash stores Microchip's AN1083 sensorless BLDC library plus application code, while the 16 KB RAM holds observer state and history. The 100-pin TQFP gives 85 I/O pins, allowing front-panel triac dimming, IR receiver input, and tachometer output alongside the 3-phase bridge. Compared with a PIC18F-only approach, the DSC cuts firmware loop time by ~3x and removes the need for an external op-amp zero-cross circuit.
Recommandé
Industrial Servo / PMSM Drive
The DSPIC33FJ128MC710T-I/PF excels in industrial PMSM servo drives that demand field-oriented control (FOC) at update rates of 8-32 kHz. Its DSP engine completes one PI current loop iteration (including Park inverse, SVPWM) in roughly 4 µs, and the dedicated 8-channel PWM with dead-time insertion and hardware fault input directly drives a 3-phase IGBT bridge. The 12-bit ADC at 1.1 Msps supports dual-shunt current sensing with simultaneous sampling, and 8 DMA channels offload encoder quadrature counters without CPU intervention. The 100-pin TQFP exposes dedicated QEI pins for incremental encoders plus CAN/ECAN for EtherCAT/CANopen networking. Designers can pair it with external gate drivers and run Microchip's MCLV-2 reference firmware directly, eliminating weeks of algorithm bring-up.
Recommandé
E-Bike / Light-EV Hub Motor Controller
In e-bike and light-EV hub-motor controllers, the DSPIC33FJ128MC710T-I/PF delivers the DSP throughput required for sinusoidal FOC with MTPA (maximum torque per amp) optimization, while its 128 KB Flash holds torque-assist maps, battery-current profiling, and CAN-bus diagnostics. The 3.0-3.6 V supply aligns with Li-ion pack-derived rails, and the 100-pin TQFP supports pedal-torque sensor input (ADC), throttle input, brake cutoff, and 3-phase half-bridge gate drives simultaneously. The motor-control PWMs include hardware dead-time and polarity control, critical for safe 36-48 V battery switching. Compared with a discrete MCU+FPGA solution, the DSC consolidates signal conditioning, control, and CAN communication in one IC, reducing BOM and improving EMI by replacing parallel logic with deterministic hardware peripherals.
Recommandé
HVAC Variable-Speed Blower / Compressor Drive
The DSPIC33FJ128MC710T-I/PF suits HVAC variable-speed blower and compressor inverters that must run quietly with low torque ripple. Its DSP engine runs space-vector modulation with harmonic-injection techniques that reduce audible switching noise below 18 kHz, while the 100-pin TQFP provides 85 I/O for thermistor inputs, 0-10 V speed reference, tach feedback, and relay outputs. The 128 KB Flash accommodates sensorless or sensored compressor control algorithms plus MODBUS/Modbus RTU firmware. Hardware CIP peripherals (CRC, PWM, ADC triggering) operate independently of the CPU, freeing MIPS for system-level diagnostics. The industrial -40 °C to +85 °C grade is well-matched to indoor/outdoor HVAC cabinet environments.
Recommandé
Washing-Machine Direct-Drive Inverter
The DSPIC33FJ128MC710T-I/PF is a strong fit for direct-drive washing-machine drum inverters where a 3-phase PMSM or BLDC motor replaces a belt-driven universal motor. Its DSP engine executes unbalanced-load compensation and drum-anti-resonance algorithms in real time at 16 kHz PWM update rate, and the 100-pin TQFP gives enough I/O for the user-interface keypad, lid-switch interlock, water-level sensor, and triac-driven water valves. The 128 KB Flash hosts IEC 60730 Class B self-test routines required for white-goods safety certification. The device's CIP peripherals execute ADC-to-PWM data movement via DMA without CPU involvement, leaving MIPS budget for power-measurement and door-lock supervisory logic. Compared with a fixed-frequency PIC16 implementation, the DSC enables true variable-speed operation that cuts energy use by 30-40%.
Recommandé
Industrial CAN-Controlled Stepper / Servo Node
The DSPIC33FJ128MC710T-I/PF operates as a CANopen or DeviceNet slave node driving a small stepper or servo axis in industrial automation. Its 40 MIPS DSP engine handles closed-loop microstepping ramps with on-the-fly profile updates, and the on-chip ECAN peripheral supports CAN 2.0B at 1 Mbit/s for synchronized multi-axis motion. The 100-pin TQFP leaves sufficient I/O for limit-switch inputs, encoder feedback, and stepper-direction outputs. The 128 KB Flash stores CANopen stack (CiA 401) plus application logic. Compared with discrete CAN-controller + MCU designs, the integrated ECAN reduces external IC count and provides deterministic message handling via DMA. The industrial temperature grade handles factory-floor thermal stress without derating.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC33FJ128MC710T-I/PF — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC33FJ128MC710-I/PF | DSPIC33FJ128MC710ATE/PF | DSPIC33FJ128MC710ATH/PF | DSPIC33FJ128MC510A-I/PF | DSPIC33FJ128GP710T-I/PF |
|---|---|---|---|---|---|---|
| Package | 100-pin TQFP (14x14) | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same | 100-pin TQFP (14x14) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| CPU Speed | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| Motor-Control PWM | 8 x 16-bit (MC family) | 8 x 16-bit (MC family) | 8 x 16-bit (MC family) | 8 x 16-bit (MC family) | 6 x 16-bit (MC family) | No dedicated MC PWMs (GP family) |
| Temperature Range | -40 to +85 °C | -40 to +85 °C | -40 to +125 °C (AEC-Q100) | -40 to +125 °C (AEC-Q100) | -40 to +85 °C | -40 to +85 °C |
| Qualification | Industrial | Industrial | AEC-Q100 Automotive | AEC-Q100 Automotive High-Temp | Industrial | Industrial |
Principaux différenciateurs
- 100-pin TQFP exposes dedicated 8-channel MC PWMs (vs DSPIC33FJ128GP710T-I/PF)
- AEC-Q100 grade option in same footprint (vs DSPIC33FJ128MC710ATE/PF)
- DSP engine executes MAC in 1 cycle (vs PIC18F23K20-I/MV)
- 40 MIPS performance headroom for sensorless algorithms (vs DSPIC33FJ128MC706T-I/PT)
Notes de conception
Place at least one 100 nF decoupling capacitor within 5 mm of every VDD/VSS pin pair on the 100-pin TQFP, and add a 10 µF bulk tantalum/ceramic capacitor near the device's main supply pin. With 85 I/O pins switching, return current paths must flow through a low-impedance ground plane; split-plane layouts near the DSC are not recommended. Place the 3-phase gate-driver stages as close as possible to the PWM outputs to keep switching-loop area small.
Analog inputs (AN0-AN23) should be routed away from PWM traces and gate-driver outputs. Use a dedicated AVSS/AGND return path if mixed-signal sensing is in use. Keep ADC traces no longer than 50 mm and guard them with ground. The dsPIC33F ADC achieves best SNR (>-60 dB) when source impedance is < 1 kΩ, so add an op-amp buffer if a high-impedance sensor (e.g. resistive divider) drives the ADC.
Estimated: At 40 MIPS continuous operation from 3.3 V, the DSPIC33FJ128MC710T-I/PF draws roughly 60-80 mA of core current (~200-265 mW). The 100-pin TQFP has a thermal resistance of approximately 40 °C/W (with 4-layer PCB and modest copper). In a sealed industrial enclosure with ambient at 70 °C, junction temperature may reach 80-85 °C - still within the -40 to +85 °C industrial rating. Add an exposed copper pad on inner layers for additional dissipation margin in high-temperature motor enclosures.
Do not float the MCLR pin - it must be tied to VDD via a 10-47 kΩ pull-up resistor, with a 100 nF cap to ground if external reset is used. Failure to bypass VDD/VSS pairs can cause code runaway during motor switching transients. Always configure the PWMSafety Fault (FLTA/FLTB) input to latch the PWM outputs in a safe state on overcurrent; software-only shutdown is too slow for IGBT/MOSFET protection.
Estimated: 100-pin TQFP requires 0.5 mm pitch traces. Use 4-layer PCB with continuous ground plane under the DSC for optimal EMI and thermal performance. Keep the crystal/oscillator within 5 mm of OSC1/OSC2 pins and guard the traces with ground. If using an external 32.768 kHz crystal for RTCC, route SOSCI/SOSCO symmetrically with respect to AVSS to maintain low jitter for timekeeping.
Informations de conformité
RoHS and lead-free compliant per Microchip product page. Industrial temperature grade (-40 to +85 °C). AEC-Q100 variants available in DSPIC33FJ128MC710ATE/PF (automotive) and DSPIC33FJ128MC710ATH/PF (high-temperature automotive).
