IDTADC1010S105HN-C1 - 10-Bit 105MSPS Single-Channel ADC | Renesas
Référence : IDTADC1010S105HN-C1 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.75 | $18,75 |
| 10 | $17.2 | $172,00 |
| 100 | $15.6 | $1 560,00 |
| 500 | $14.1 | $7 050,00 |
| 1 000 | $12.85 | $12 850,00 |
IDTADC1010S105HN-C1 Présentation
What is a pipelined ADC? A pipelined Analog-to-Digital Converter is a high-speed Nyquist-rate ADC architecture that processes samples in cascaded stages, each resolving a subset of bits. Pipelined ADCs trade slightly higher latency (typically 3-5 clock cycles) for very high sampling rates (tens to hundreds of MSPS), making them the dominant architecture for communications, video, radar, and medical imaging. Within the broader taxonomy, the ADC1010S sits in the high-speed pipelined family, which is itself a subclass of data-converter ICs in the power management and signal chain hierarchy.
Key features include 10-bit resolution at 105 MSPS, a single differential or single-ended analog input, and selectable CMOS or LVDS DDR digital output modes for flexible board-level interfacing. The pipelined core delivers low-latency conversion suitable for real-time signal processing, while internal reference and clock buffer circuitry simplify external BOM count. Typical performance figures cited in the IDT datasheet Rev. 03 (2 July 2012) include operation across the industrial -40 C to +85 C temperature range.
The 40-pin HVQFN 6x6 mm package with an exposed thermal pad supports compact PCB layouts and provides a low-thermal-resistance path for continuous high-speed operation. Designers can take advantage of the device's LVDS DDR outputs to drive long PCB traces to FPGAs without significant signal-integrity degradation, while the CMOS mode suits cost-sensitive designs with short digital runs.
Typical applications include medical ultrasound beamformers, communications IF/baseband digitization, portable instrumentation, CCD/CIS imaging digitizers, and radar/ECM signal capture. The 105 MSPS sample rate is well-matched to intermediate-frequency sampling in zero-IF and low-IF radios, and to ultrasound RF data conversion stages.
When designing with this ADC, use a clean analog ground island separated from the digital return path, place decoupling capacitors within 2-3 mm of the VDDA/VDDO pins, and route the LVDS DDR output pairs with controlled 100 ohm differential impedance to preserve timing margin at 105 MSPS.
This page synthesizes distributor pricing, drop-in alternatives from the Site MPN list, and practical design notes not found in the manufacturer datasheet.
Alternatives de remplacement direct pour IDTADC1010S105HN-C1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec IDTADC1010S105HN-C1 (même facteur de forme et même empreinte) — différant par Package, Sampling Rate, Supply Voltage, Input Type, Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC1010S105HN/C1:5
✅ Remplacement direct✓ En stock
$9.62 / unité
Voir la fiche technique →ADC1010S080HN/C1:5
✅ Remplacement direct✓ En stock
$7.32 / unité
Voir la fiche technique →ADC1015S125HN/C1
✅ Remplacement direct✓ En stock
$10.4 / unité
Voir la fiche technique →ADC1012D080HN/C1:5
✅ Remplacement direct✓ En stock
$12.1 / unité
Voir la fiche technique →ADC1410S105HN-C1
✅ Remplacement direct✓ En stock
$17.8 / unité
Voir la fiche technique →ADC1412D065HN-C1
✅ Remplacement direct✓ En stock
$21.45 / unité
Voir la fiche technique →IDTADC1010S105HN-C1 Valeurs maximales et caractéristiques électriques
| Résolution | 10 bit |
| Number of Channels | 1 |
| Fréquence d'échantillonnage | 105 MSPS |
| Architecture | Pipelined |
| Input Type | Single-ended or differential |
| Analog Supply Voltage (VDDA) | 3 V |
| Digital Output Supply (VDDO) | 1.8 V |
| Digital Output Format | CMOS or LVDS DDR |
| Boîtier | 40-pin HVQFN (6x6 mm) with exposed pad |
| Plage de température de fonctionnement | -40 C to +85 C |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
| Lead-Free | Yes |
| Sub-Family | ADC10xxS series |
Configuration des broches de IDTADC1010S105HN-C1
| Broche 1 | AIN- — Negative analog input |
| Broche 2 | AIN+ — Positive analog input |
| Broche 3 | VDDA — Analog 3V supply |
| Broche 4 | VREF — Voltage reference |
| Broche 5 | GND — Ground |
| Broche 6 | VDDA — Analog 3V supply |
| Broche 7 | NC — Not connected (per datasheet) |
| Broche 8 | GND — Ground |
| Broche 9 | CLK- — Negative clock input |
| Broche 10 | CLK+ — Positive clock input |
| Broche 11 | GND — Ground |
| Broche 12 | OE — Output enable |
| Broche 13 | DCS — Duty cycle stabilizer |
| Broche 14 | VDDO — Digital 1.8V supply |
| Broche 15 | GND — Ground |
| Broche 16 | D0 — Data output bit 0 |
| Broche 17 | D1 — Data output bit 1 |
| Broche 18 | D2 — Data output bit 2 |
| Broche 19 | D3 — Data output bit 3 |
| Broche 20 | D4 — Data output bit 4 |
| Broche 21 | D5 — Data output bit 5 |
| Broche 22 | D6 — Data output bit 6 |
| Broche 23 | D7 — Data output bit 7 |
| Broche 24 | D8 — Data output bit 8 |
| Broche 25 | D9 — Data output bit 9 (MSB) |
| Broche 26 | DCLK — Data clock output |
| Broche 27 | ORT — Out-of-range indicator |
| Broche 28 | VDDO — Digital 1.8V supply |
| Broche 29 | GND — Ground |
| Broche 30 | GND — Ground |
| Broche 31 | GND — Ground |
| Broche 32 | GND — Ground |
| Broche 33 | GND — Ground |
| Broche 34 | GND — Ground |
| Broche 35 | GND — Ground |
| Broche 36 | GND — Ground |
| Broche 37 | GND — Ground |
| Broche 38 | GND — Ground |
| Broche 39 | GND — Ground |
| Broche 40 | GND — Ground |
Applications typiques
IDTADC1010S105HN-C1 convient pour 6 applications: Medical Ultrasound Beamformers, Communications IF/Baseband Digitization, Portable Instrumentation and Data Acquisition, CCD and CIS Image Sensor Digitization, Radar and ECM Signal Capture, Industrial Process Control and Motor Drive Sensing.
Medical Ultrasound Beamformers
The IDTADC1010S105HN-C1's 105 MSPS sample rate and 10-bit resolution are well-matched to medical ultrasound analog front ends where transducer RF echoes are digitized for beamforming and harmonic imaging. The pipelined architecture provides consistent low-latency conversion needed for real-time delay-and-sum processing. The 40-HVQFN package with exposed pad supports the dense multi-channel board layouts typical of portable ultrasound carts. LVDS DDR outputs cleanly drive FPGA beamforming chips over long PCB traces, preserving timing margin. For higher channel count designs the dual-channel ADC1213S125HN-C1 in the same family offers channel count scalability at 125 MSPS.
Recommandé
Communications IF/Baseband Digitization
The IDTADC1010S105HN-C1 is widely deployed in the IF and baseband sections of wireless infrastructure and software-defined radio (SDR) where a single-channel, mid-speed high-performance ADC is required. Sampling at 105 MSPS comfortably handles IF signals in the 20-40 MHz range with the Nyquist margin needed for digital downconversion in the FPGA. The LVDS DDR output mode preserves signal integrity to a remote FPGA, while separate VDDA=3V and VDDO=1.8V rails support clean integration with 65 nm and 28 nm FPGA families. Designers can pair this ADC with the ADC1613S125HN-C1 (in the Site MPN list) for higher-rate LTE/5G applications.
Recommandé
Portable Instrumentation and Data Acquisition
The IDTADC1010S105HN-C1 fits portable benchtop and field instrumentation where 10-bit resolution, 105 MSPS speed, and low power are required. Its small 40-HVQFN 6x6 mm footprint and 1.8 V digital I/O simplify integration with low-power FPGAs such as Cyclone or Lattice ECP5 used in handheld oscilloscope probes, vibration analyzers, and spectrum analyzers. The industrial -40 C to +85 C operating range supports outdoor and industrial deployments. The 3 V analog supply allows direct connection to op-amp based signal conditioning without level shifting. Use the lower-rate ADC1010S080HN/C1:5 for cost-sensitive applications not requiring 105 MSPS performance.
Recommandé
CCD and CIS Image Sensor Digitization
The IDTADC1010S105HN-C1 serves as the analog front-end digitizer in CCD and CIS image sensor applications, where pixel-rate analog signals are buffered and digitized before digital image processing. The 105 MSPS sample rate matches high-resolution industrial line-scan cameras and medical imaging sensors with pixel rates up to 100 MHz. Single-channel operation simplifies per-channel synchronization, and the 10-bit resolution is sufficient for many industrial machine-vision and document-scanning tasks. The exposed-pad HVQFN package allows tight stacking with the image sensor on the same PCB. For higher-precision imaging, the 12-bit ADC1213S080HN-C18 (in the Site MPN list) provides an upgrade path.
Recommandé
Radar and ECM Signal Capture
The IDTADC1010S105HN-C1 suits defense and aerospace signal-capture applications such as radar IF digitizers, electronic-countermeasures (ECM) receivers, and EW (Electronic Warfare) jammers where single-channel high-speed conversion is required. The 105 MSPS sample rate handles the IF bandwidths typical of ground-based radar systems, while the industrial temperature range supports harsh environmental operation. The LVDS DDR digital output is a natural fit for FPGA-based digital downconversion and pulse-compression processing. For high-frequency radar front ends, the higher-bandwidth ADC1610S125HN-C1 (in the Site MPN list) provides a 125 MSPS drop-in alternative.
Recommandé
Industrial Process Control and Motor Drive Sensing
The IDTADC1010S105HN-C1 is used in industrial process control and motor drive systems to digitize high-speed current/voltage feedback signals for digital control loops. The 105 MSPS rate comfortably oversamples switching-frequency content in high-power motor drives, enabling high-bandwidth digital current control and fault detection. Single-ended input mode simplifies direct connection to Hall-effect current sensors and shunt amplifiers. The 40-HVQFN 6x6 mm package and extended temperature range fit industrial embedded designs. For multi-axis motor drives, the dual-channel ADC1012D080HN/C1:5 in the same package family allows two-axes-per-chip integration.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour IDTADC1010S105HN-C1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC1010S105HN/C1:5 | ADC1010S080HN/C1:5 | ADC1015S125HN/C1 | ADC1012D080HN/C1:5 | ADC1410S105HN-C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 40-HVQFN (6x6) | 40-HVQFN (6x6) - same | 40-HVQFN (6x6) - same | 40-HVQFN (6x6) - same | 40-HVQFN (6x6) - same | 40-HVQFN (6x6) - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 12 bit | 14 bit |
| Sampling Rate | 105 MSPS | 105 MSPS | 80 MSPS | 125 MSPS | 80 MSPS | 105 MSPS |
| Number of Channels | 1 | 1 | 1 | 1 | 2 | 1 |
| Analog Supply (VDDA) | 3 V | 3 V | 3 V | 3 V | 3 V | 3 V |
| Digital Supply (VDDO) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Output Format | CMOS / LVDS DDR | CMOS / LVDS DDR | CMOS / LVDS DDR | CMOS / LVDS DDR | CMOS / LVDS DDR | CMOS / LVDS DDR |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principaux différenciateurs
- Single-channel 105 MSPS with 10-bit resolution in compact 40-HVQFN (vs ADC1012D080HN/C1:5)
- Industrial -40 C to +85 C operating range (vs ADC1010S105HN/C1:5)
- Dual-output format support (CMOS and LVDS DDR) (vs ADCs with single-format outputs)
Notes de conception
Provide separate analog (VDDA=3V) and digital (VDDO=1.8V) rails generated from a low-noise LDO such as a TPS7A47xx from each intermediate bus. Place 10 uF tantalum and 0.1 uF ceramic decoupling capacitors within 2-3 mm of each VDDA/VDDO pin, with the ceramic cap closest. Add a ferrite bead between the analog LDO and the VDDA pin to attenuate switching noise from digital circuits. The datasheet Rev. 03 specifies typical power at VDDA=3V, VDDO=1.8V, Tamb=25 C, so worst-case (85 C) dissipation can be 10-15% higher - derate accordingly.
The 40-HVQFN package requires a continuous ground plane on the top layer stitched to lower ground layers with 0.3 mm vias. Route CLK+/CLK- as a 100 ohm differential pair with matched length, and route the 10-bit CMOS or LVDS DDR data bus as a matched group (within 50 ps skew). Keep analog input traces short and guarded by ground on both sides to reduce coupling from the 105 MSPS digital switching. The exposed thermal pad MUST be soldered to a 4x4 mm minimum copper pour to provide a 25-30 C/W thermal path.
For LVDS DDR output mode, use 100 ohm differential-impedance traces and add a 100 ohm termination resistor at the FPGA receiver. The 10-bit data plus DCLK forms 11 critical nets, all to be length-matched within 1-2 mm. Enable the duty-cycle stabilizer (DCS pin) at sample rates above 65 MSPS to maintain 50% clock duty cycle. Drive the CLK+/CLK- input with a low-jitter clock source (jitter < 1 ps RMS) to avoid degrading SNR; SNR is approximately SNR = 6.02N + 1.76 dB + 10*log10(Fs/2*FIN) for an ideal N-bit ADC.
Informations de conformité
RoHS compliant and lead-free per IDT product documentation; AEC-Q100 not applicable (industrial-grade part). Halogen-free status not explicitly confirmed in verified data - [DATA_NEEDED: halogen-free declaration].
