INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)
Référence : INA240A4DR ✗ Fin de vieINA240A4DR Présentation
A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology.
The INA240A4DR provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads.
The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4DR to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems.
Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction.
For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span.
This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4DR. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.
Alternatives de remplacement direct pour INA240A4DR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesINA240A4DR Valeurs maximales et caractéristiques électriques
| Product Type | Bidirectional zero-drift current-sense amplifier |
| Number of Channels | 1 channel |
| Common-Mode Voltage Range | -4 V to 80 V |
| Type de sortie | Voltage output |
| Gain Bandwidth Product | 100 kHz |
| Common-Mode Rejection Ratio | 120 dB |
| Input Bias Current | 90 µA |
| Operating Supply Current | 1.8 mA |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +125 °C |
| Boîtier | 8-pin SOIC |
| Nombre de broches | 8 pins |
| Style de montage | SMD/SMT surface mount |
| Shipping Packaging | Tube |
| PWM Rejection | Enhanced |
| Bidirectional Sensing | Supported |
Guide de configuration des broches du INA240A4DR 8-pin soic
Configuration des broches du INA240A4DR (boîtier 8-pin soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour INA240A4DR.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
INA240A4DR convient pour 6 applications: Motor Current Feedback, Solenoid and Flyback Monitoring, Battery-Pack Current Telemetry, Industrial Power-Supply Telemetry, Inverter and Power-Stage Control, Current Sharing in Paralleled Supplies.
Motor Current Feedback
The INA240A4DR is suitable for motor-current feedback because it measures shunt-resistor voltage across a -4 V to 80 V common-mode range and supports bidirectional current. Its 120 dB CMRR helps the controller distinguish the small differential shunt signal from voltage excursions on the motor-supply node. Place the device near the shunt and route the input pair as a compact differential pair. The design must confirm that the expected positive and negative shunt voltages, the amplifier gain, and the controller input range produce an accurate signal without exceeding the output limits.
Solenoid and Flyback Monitoring
The negative common-mode capability of the INA240A4DR is useful in solenoid-driver systems where the monitored node can move below ground during flyback. Its -4 V to 80 V common-mode range allows one amplifier to monitor a shunt during both driven and decay intervals, while enhanced PWM rejection improves behavior during rapid switching transitions. The circuit should include properly rated flyback protection and keep the amplifier input path close to the shunt. Verify the shunt dissipation, transient margins, and the output range for both current directions before production use.
Battery-Pack Current Telemetry
INA240A4DR can support battery-pack current telemetry when the shunt and sensing platform must accommodate voltages below ground or up to 80 V. Its bidirectional measurement supports charge, discharge, and regeneration monitoring without reversing the signal path, while the 1.8 mA operating supply current is useful for power-conscious systems. The shunt must be sized for maximum current, and the amplifier output must be checked against the ADC range. Local supply decoupling and careful common-mode layout remain necessary despite the amplifier's high CMRR.
Industrial Power-Supply Telemetry
The INA240A4DR is appropriate for reporting current in industrial power converters where the sensing node can sit at a high common-mode voltage relative to the measurement electronics. Its common-mode range is independent of the supply voltage, allowing a low-voltage sensing supply to monitor a higher-voltage power rail. The 100 kHz gain-bandwidth product supports the bandwidth available for current-loop feedback, although the complete loop must also be assessed for phase margin. Use the manufacturer electrical tables to confirm gain, output swing, and response time against the converter's requirements.
Inverter and Power-Stage Control
INA240A4DR can provide isolated-current information for inverter and power-stage control because it accepts a wide common-mode range and rejects common-mode disturbance through 120 dB CMRR. Enhanced PWM rejection is valuable when switching transitions create large voltage changes across the monitored node. The amplifier output can be routed to a controller or ADC for protection and closed-loop current regulation. Designers should preserve the differential geometry of the shunt connections and account for propagation delay when tuning the control loop.
Current Sharing in Paralleled Supplies
INA240A4DR can measure individual branch current in a system that uses paralleled power converters, allowing a controller to compare branch loading and adjust each converter. Bidirectional sensing makes the measurement useful during startup transitions and when power flow changes between branches. The shunt should be placed in the branch whose current is being controlled, while the amplifier input traces should be minimized to reduce pickup from adjacent switching nodes. Confirm that the selected gain preserves adequate resolution at light load and that the output remains within range at maximum branch current.
Données de référence d'ingénierie pour INA240A4DR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 8-pin SOIC |
| Brand | Texas Instruments |
| Product Type | Bidirectional voltage-output current-sense amplifier |
| Number of Channels | 1 channel |
| Common-Mode Voltage Range | -4 V to 80 V |
| CMRR | 120 dB |
| Gain-Bandwidth Product | 100 kHz |
| Input Bias Current | 90 µA |
| Operating Supply Current | 1.8 mA |
| Operating Temperature | -40 °C to +125 °C |
Notes de conception
Route the two shunt connections to INA240A4DR as a compact, symmetric differential pair. Keep the amplifier close to the shunt so that the sensed voltage is not exposed to additional copper area or switching-node pickup. The -4 V to 80 V common-mode range allows a wide sensing voltage span, but it does not remove the need for careful high-impedance layout around the input pins.
Connect the supply bypass capacitor close to the device's supply and ground pins, and provide a low-impedance return path from the amplifier to the system ground. Verify that the PCB land pattern and thermal-pad connection match the 8-pin SOIC package drawing for INA240A4DR. Incorrect exposed-pad soldering or an unintended connection can affect stability, thermal performance, and measurement accuracy.
Do not select the amplifier gain without checking the maximum shunt drop and the downstream ADC or controller input range. Excessive gain can clip the output, while insufficient gain can waste ADC resolution. Also verify that the shunt's pulse rating covers motor, solenoid, or inverter transients rather than relying only on its steady-state resistance.
Enhanced PWM rejection does not remove every requirement for good signal-chain design. Minimize shunt-node copper, avoid routing the input pair beneath high dv/dt power paths, and use the input-filter approach specified by the manufacturer for the intended bandwidth. Confirm that filtering does not add excessive phase delay to a closed-loop current-control path.
Informations de conformité
The manufacturer identifies INA240A4DR as no longer in production. Compliance status was not stated in the manufacturer or distributor catalog information and therefore remains unknown.