آخری بار خریداری کا نوٹس: INA240A4DR اپنی زندگی کے اختتام کے قریب ہے۔ آخری آرڈر کی تاریخ: ہم سے رابطہ کریں. دستیاب متبادل پرزے دیکھیں →
Texas Instruments

INA240A4DR - 80V Bidirectional Current Sense Amp | Texas Instruments (Tape & Reel)

MPN: INA240A4DR ✗ اختتامِ زندگی
-4 V to 80 V Vdss 90 µA Id 8-pin SOIC Package
MOQ: 1 |

INA240A4DR جائزہ

The Texas Instruments INA240A4DR is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V.

A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology.

The INA240A4DR provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads.

The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4DR to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems.

Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction.

For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span.

This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4DR. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

کے لیے ڈراپ اِن متبادل INA240A4DR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔

متبادل کی درخواست کریں

INA240A4DR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Product Type Bidirectional zero-drift current-sense amplifier
Number of Channels 1 channel
Common-Mode Voltage Range -4 V to 80 V
آؤٹ پٹ کی قسم Voltage output
Gain Bandwidth Product 100 kHz
Common-Mode Rejection Ratio 120 dB
Input Bias Current 90 µA
Operating Supply Current 1.8 mA
Minimum Operating Temperature -40 °C
Maximum Operating Temperature +125 °C
پیکیج 8-pin SOIC
پن کی تعداد 8 pins
ماؤنٹنگ اسٹائل SMD/SMT surface mount
Shipping Packaging Tube
PWM Rejection Enhanced
Bidirectional Sensing Supported

INA240A4DR 8-pin soic پن کنفیگریشن گائیڈ

INA240A4DR (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

INA240A4DR کے لیے 8-pin soic پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں INA240A4DR.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

INA240A4DR کے لیے موزوں ہے 6 ایپلیکیشنs: Motor Current Feedback, Solenoid and Flyback Monitoring, Battery-Pack Current Telemetry, Industrial Power-Supply Telemetry, Inverter and Power-Stage Control, Current Sharing in Paralleled Supplies.

🏭

Motor Current Feedback

The INA240A4DR is suitable for motor-current feedback because it measures shunt-resistor voltage across a -4 V to 80 V common-mode range and supports bidirectional current. Its 120 dB CMRR helps the controller distinguish the small differential shunt signal from voltage excursions on the motor-supply node. Place the device near the shunt and route the input pair as a compact differential pair. The design must confirm that the expected positive and negative shunt voltages, the amplifier gain, and the controller input range produce an accurate signal without exceeding the output limits.

⚡

Solenoid and Flyback Monitoring

The negative common-mode capability of the INA240A4DR is useful in solenoid-driver systems where the monitored node can move below ground during flyback. Its -4 V to 80 V common-mode range allows one amplifier to monitor a shunt during both driven and decay intervals, while enhanced PWM rejection improves behavior during rapid switching transitions. The circuit should include properly rated flyback protection and keep the amplifier input path close to the shunt. Verify the shunt dissipation, transient margins, and the output range for both current directions before production use.

🔋

Battery-Pack Current Telemetry

INA240A4DR can support battery-pack current telemetry when the shunt and sensing platform must accommodate voltages below ground or up to 80 V. Its bidirectional measurement supports charge, discharge, and regeneration monitoring without reversing the signal path, while the 1.8 mA operating supply current is useful for power-conscious systems. The shunt must be sized for maximum current, and the amplifier output must be checked against the ADC range. Local supply decoupling and careful common-mode layout remain necessary despite the amplifier's high CMRR.

🏭

Industrial Power-Supply Telemetry

The INA240A4DR is appropriate for reporting current in industrial power converters where the sensing node can sit at a high common-mode voltage relative to the measurement electronics. Its common-mode range is independent of the supply voltage, allowing a low-voltage sensing supply to monitor a higher-voltage power rail. The 100 kHz gain-bandwidth product supports the bandwidth available for current-loop feedback, although the complete loop must also be assessed for phase margin. Use the manufacturer electrical tables to confirm gain, output swing, and response time against the converter's requirements.

⚡

Inverter and Power-Stage Control

INA240A4DR can provide isolated-current information for inverter and power-stage control because it accepts a wide common-mode range and rejects common-mode disturbance through 120 dB CMRR. Enhanced PWM rejection is valuable when switching transitions create large voltage changes across the monitored node. The amplifier output can be routed to a controller or ADC for protection and closed-loop current regulation. Designers should preserve the differential geometry of the shunt connections and account for propagation delay when tuning the control loop.

🖥️

Current Sharing in Paralleled Supplies

INA240A4DR can measure individual branch current in a system that uses paralleled power converters, allowing a controller to compare branch loading and adjust each converter. Bidirectional sensing makes the measurement useful during startup transitions and when power flow changes between branches. The shunt should be placed in the branch whose current is being controlled, while the amplifier input traces should be minimized to reduce pickup from adjacent switching nodes. Confirm that the selected gain preserves adequate resolution at light load and that the output remains within range at maximum branch current.

What is the INA240A4DR?
The INA240A4DR is a single-channel, bidirectional, voltage-output current-sense amplifier from Texas Instruments. According to the manufacturer datasheet, Revision C, it senses shunt-resistor voltage over a -4 V to 80 V common-mode range, provides enhanced PWM rejection, and is packaged in an 8-pin SOIC. Its zero-drift operation supports accurate monitoring of positive and negative current in power-conversion and motor-control systems.
What is the common-mode voltage range of INA240A4DR?
The INA240A4DR operates across a -4 V to 80 V common-mode voltage range, independently of its supply voltage. According to the Texas Instruments INA240 datasheet, Revision C, the negative margin allows the input to remain below ground during the flyback period of typical solenoid applications, while the 80 V upper limit supports monitoring of higher-voltage power buses.
What are the key specifications of INA240A4DR that engineers should know?
The INA240A4DR combines a -4 V to 80 V common-mode range with 120 dB CMRR, a 100 kHz gain-bandwidth product, 90 µA input bias current, and 1.8 mA operating supply current. Texas Instruments specifies a -40 °C to +125 °C operating-temperature range and an 8-pin SOIC package. These specifications make it suitable for precision current feedback in electrically noisy power systems.
Where can I download the INA240A4DR datasheet PDF?
The official INA240A4DR datasheet PDF is available from the Texas Instruments document link on this page. The manufacturer identifies the document as Revision C and describes the INA240 as a -4 V to 80 V bidirectional current-sense amplifier with enhanced PWM rejection. Use the manufacturer PDF for the complete pin description, electrical characteristics, timing information, and application guidance.
Where can I find the INA240A4DR pinout?
The INA240A4DR uses an 8-pin SOIC package, but its complete numbered pin description is not reproduced on this page. Use the pin-description table in the Texas Instruments INA240 datasheet, Revision C, when assigning PCB tracks and confirming input, output, supply, and ground connections. The device also has an exposed thermal pad arrangement that must be checked in the package drawing.
Is the INA240A4DR still in production?
No, the manufacturer lists the INA240A4DR as no longer in production. Texas Instruments identifies the part as a -4 V to 80 V bidirectional current-sense amplifier in an 8-pin SOIC package, but its part-details page still provides a datasheet and alternate-part information. For a new production design, request the current lifecycle and sourcing position through the Request a Quote form on this page.
Where can I buy INA240A4DR online?
Use the Request a Quote form on this page to request the INA240A4DR, current availability, package quantity, and a formal quotation. The manufacturer lists the standard INA240A4DR in tube packaging, while the device is no longer in production. A quote request allows the production status, lot traceability, and any available surplus to be confirmed before committing an active design to this orderable variant.
What is the price of INA240A4DR?
The current commercial terms for INA240A4DR should be requested through the Request a Quote form on this page. Because Texas Instruments identifies this orderable variant as no longer in production, its commercial status can change independently of the historical catalog listing. The quote process is the appropriate way to confirm unit availability, quantity breaks, and any traceability requirements for your planned volume.
What is the lead time for INA240A4DR?
The current lead time for INA240A4DR should be confirmed through the Request a Quote form on this page. The manufacturer lists the part as no longer in production, so a production lead time cannot be inferred from the product-page description alone. Request a quotation for the required quantity and tube package to obtain an accurate schedule, including any available surplus or scheduled allocation.
Is INA240A4DR in stock?
Stock for INA240A4DR should be confirmed through the Request a Quote form on this page. The manufacturer states that this variant is no longer in production, while distributor catalog pages can continue to display historical product records after supply changes. Ask the quote team to verify the exact INA240A4DR suffix, package, quantity, date code, and inspectability requirements before treating the device as available.
What is the difference between INA240 and INA240A4DR?
INA240 is the amplifier-family name, while INA240A4DR identifies one specific gain and package configuration in that family. Texas Instruments describes both as -4 V to 80 V bidirectional, zero-drift current-sense amplifiers with enhanced PWM rejection. The INA240A4DR is specifically offered in an 8-pin SOIC package with an operating range of -40 °C to +125 °C.
INA240A4DR vs INA240A3D - which is better for motor-current feedback?
The correct choice depends primarily on the required shunt voltage and ADC input range because INA240A4DR and INA240A3D belong to the same pin-compatible family but represent different gain settings. Compare the target full-scale shunt drop against both amplifier gain options and the downstream converter limit. The manufacturer datasheet should be used to select the gain that provides useful resolution without clipping.
When should I choose INA240A4DR over another INA240 gain option?
Choose INA240A4DR when its higher-gain configuration maps the expected shunt voltage into the available ADC or controller input range with suitable headroom. The decision must also account for output swing, offset accuracy, bandwidth, and the -4 V to 80 V common-mode requirement. Because the part is no longer in production, choose it primarily for controlled replacement or existing-product continuity.
Is INA240A4DR suitable for bidirectional motor-current measurement?
Yes, INA240A4DR supports bidirectional current measurement because it is a bidirectional voltage-output current-sense amplifier with a -4 V to 80 V common-mode range. According to the Texas Instruments datasheet, Revision C, the negative common-mode capability also accommodates the below-ground flyback period of typical solenoid applications. The shunt, gain, and output range must be sized together for the expected positive and negative current.
What can replace INA240A4DR?
A valid replacement must preserve the 8-pin SOIC footprint, pin functions, -4 V to 80 V common-mode operation, bidirectional measurement behavior, and the required gain and accuracy. The manufacturer part-details page provides alternate-part information for the INA240 family, while no verified cross-brand, pin-compatible replacement is established here. Use the Request a Quote form to request an active alternate and confirm its electrical and lifecycle equivalence.
What is the best Texas Instruments equivalent for INA240A4DR?
The closest manufacturer-family choice is an active INA240 variant with the same gain, electrical ratings, and 8-pin SOIC pin arrangement. TI's part-details page lists INA240A4DR as no longer in production and provides alternate-part information, but the required gain and lifecycle must be confirmed before substitution. Request current alternates through the Request a Quote form rather than changing the PCB footprint without manufacturer verification.

کے لیے انجینئرنگ ریفرنس ڈیٹا INA240A4DR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose INA240A4DR for controlled continuity of an existing design that uses its specific gain, 8-pin SOIC footprint, -4 V to 80 V common-mode range, and enhanced PWM-rejection behavior. It is especially relevant in bidirectional motor, solenoid, battery, and industrial power-conversion systems where the sensed node can move below ground. Its 120 dB CMRR, 100 kHz gain-bandwidth product, and 1.8 mA operating supply current support precise low-power monitoring. However, Texas Instruments lists this exact variant as no longer in production. For a new design, request an active INA240-family alternative and verify gain, output swing, offset, common-mode limits, package, and lifecycle. Do not substitute solely by package name: the shunt range, output swing, control-loop bandwidth, and thermal requirements must also remain compatible.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ
Package 8-pin SOIC
Brand Texas Instruments
Product Type Bidirectional voltage-output current-sense amplifier
Number of Channels 1 channel
Common-Mode Voltage Range -4 V to 80 V
CMRR 120 dB
Gain-Bandwidth Product 100 kHz
Input Bias Current 90 µA
Operating Supply Current 1.8 mA
Operating Temperature -40 °C to +125 °C

ڈیزائن نوٹس

Route the two shunt connections to INA240A4DR as a compact, symmetric differential pair. Keep the amplifier close to the shunt so that the sensed voltage is not exposed to additional copper area or switching-node pickup. The -4 V to 80 V common-mode range allows a wide sensing voltage span, but it does not remove the need for careful high-impedance layout around the input pins.

Connect the supply bypass capacitor close to the device's supply and ground pins, and provide a low-impedance return path from the amplifier to the system ground. Verify that the PCB land pattern and thermal-pad connection match the 8-pin SOIC package drawing for INA240A4DR. Incorrect exposed-pad soldering or an unintended connection can affect stability, thermal performance, and measurement accuracy.

Do not select the amplifier gain without checking the maximum shunt drop and the downstream ADC or controller input range. Excessive gain can clip the output, while insufficient gain can waste ADC resolution. Also verify that the shunt's pulse rating covers motor, solenoid, or inverter transients rather than relying only on its steady-state resistance.

Enhanced PWM rejection does not remove every requirement for good signal-chain design. Minimize shunt-node copper, avoid routing the input pair beneath high dv/dt power paths, and use the input-filter approach specified by the manufacturer for the intended bandwidth. Confirm that filtering does not add excessive phase delay to a closed-loop current-control path.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer identifies INA240A4DR as no longer in production. Compliance status was not stated in the manufacturer or distributor catalog information and therefore remains unknown.

متعلقہ تلاشیں

INA240A4DR datasheet INA240A4DR pinout INA240A4DR datasheet pdf INA240A4DR equivalent INA240A4DR replacement INA240A4DR footprint INA240A4DR application circuit INA240A4DR price Texas Instruments INA240A4DR INA240A4DR vs INA240A3D INA240A4DR current sense amplifier INA240A4DR -4V 80V

متعلقہ اجزاء اور اصطلاحات

Texas Instruments INA240A4DR INA240 current-sense amplifier instrumentation amplifier voltage-output amplifier bidirectional current sensing zero-drift amplifier common-mode voltage common-mode rejection ratio CMRR enhanced PWM rejection gain-bandwidth product GBP shunt resistor flyback voltage motor-control feedback battery telemetry industrial power conversion 8-pin SOIC SOIC package family surface-mount package SMD/SMT RoHS REACH AEC-Q100
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں