ISL68222IRAZ - Digital 5-Phase PWM Controller | Renesas | POL/DDR
Référence : ISL68222IRAZ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $3.58 | $3,58 |
| 10 | $3.22 | $32,20 |
| 100 | $2.87 | $287,00 |
| 500 | $2.55 | $1 275,00 |
| 1 000 | $2.27 | $2 270,00 |
ISL68222IRAZ Présentation
A buck (step-down) DC-DC controller is a power management IC that drives external MOSFETs to convert a higher DC input voltage to a lower regulated output voltage. Digital multiphase controllers like the ISL68222IRAZ add PMBus telemetry, adaptive dead-time control, diode emulation, and automatic phase add/drop for light-load efficiency. They sit in the power management hierarchy as follows: PMIC → DC-DC controller → multiphase buck controller → voltage regulator module (VRM) for CPU/GPU/DDR rails.
Key features include: support for up to five phases across two outputs (e.g., 4+1, 3+2, 3+1, 2+1, or 5+0), per-phase cycle-by-cycle current limiting with adaptive overcurrent protection, differential remote voltage sensing, ±0.5% output voltage accuracy across line/load/temperature, configurable switching frequency, AVSBus and PMBus v1.3 compliance, and extensive fault logging via SMBus. Diode emulation and automatic phase add/drop optimize light-load efficiency, while the synthetic current modulation scheme minimizes output capacitor count.
The ISL68222IRAZ uses a digital core with proprietary Renesas modulation firmware, replacing analog compensation networks with adaptive digital control. This simplifies loop compensation, enables configuration changes via PMBus instead of hardware rework, and provides oscilloscope-like telemetry of VIN/VOUT/IIN/IOUT/PIN/POUT/TEMP for advanced power-system health monitoring. The 40-pin 5x5 TQFN package exposes multiple PWM outputs, current-sense inputs, and the AVSBus/PMBus/SMBus serial interfaces.
Typical applications include DDR5/DDR4 memory VRPM (voltage regulation with power management), server and datacentre CPU/SoC core rails, FPGA and ASIC POL supplies, telecom base-station point-of-load converters, and high-end graphics card power. The dual-output flexibility also supports designs that need one rail for VDDQ and another for VTT termination, with phase shedding across both rails for maximum light-load efficiency.
When designing with the ISL68222IRAZ, use Renesas PowerNavigator software to configure the part over PMBus and tune the per-loop PID coefficients. Place the ISL68222IRAZ close to the driver/MOSFET power stage, keep the current-sense traces short and matched, and provide adequate copper pour for the 40-pin TQFN thermal pad (this is a controller, not a power dissipator, so thermal concerns are modest).
This page synthesizes distributor pricing, real drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ISL68222IRAZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ISL68222IRAZ (même facteur de forme et même empreinte) — différant par Number of Outputs, Operating Temperature, Package, Topology.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ISL68233IRAZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL68222IRAZ-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL68222IRAZ Valeurs maximales et caractéristiques électriques
| Topologie | Synchronous Step-Down (Buck) Controller |
| Nombre de sorties | 2 (configurable, X + Y ≤ 5 phases) |
| Maximum Total Phases | 5 |
| Output Configuration Examples | 5+0, 4+1, 3+2, 3+1, 2+1, 1+1 |
| Output Voltage Accuracy | ±0.5% (line/load/temperature) |
| Serial Interface | PMBus v1.3 / AVSBus / SMBus |
| Current Sense | Per-phase, adaptive overcurrent protection |
| Fréquence de commutation | Configurable via PMBus |
| Light-Load Efficiency | Diode emulation + automatic phase add/drop |
| Telemetry | VIN, VOUT, IIN, IOUT, PIN, POUT, TEMP |
| Fault Protection | OCP, OVP, UVP, OTP, cycle-by-cycle current limit |
| Boîtier | 40-pin TQFN (5x5 mm) |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40C to +85C (industrial) |
| Statut RoHS | Compliant |
Guide de configuration des broches du ISL68222IRAZ 40-pin tqfn (5x5 mm)
Configuration des broches du ISL68222IRAZ (boîtier 40-pin tqfn (5x5 mm)). Ce composant de puissance comporte des bornes de grille, de drain et de source. Pour les boîtiers non polarisés, consultez la fiche technique du fabricant pour l'orientation exacte de la broche 1 et les détails de l'empreinte. Les applications courantes incluent la conception d'alimentations, la commande de moteurs et la commutation de charges.
Aucune donnée de brochage détaillée disponible pour ISL68222IRAZ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ISL68222IRAZ convient pour 6 applications: DDR5 / DDR4 Memory VRPM, Server / Datacentre CPU and SoC POL, FPGA / ASIC Point-of-Load Supplies, Telecom Base-Station Point-of-Load, High-End Graphics Card / GPU VRM, Industrial Embedded Computing / Edge Server.
DDR5 / DDR4 Memory VRPM
The ISL68222IRAZ's dual-output architecture (X+Y ≤ 5) makes it ideal for DDR5/DDR4 memory VRPM rails: configure phases as 2+1 or 3+1 to power VDDQ plus the VTT termination rail from one IC. Its ±0.5% VOUT accuracy across line/load/temperature meets JEDEC DDR rail tolerances, while PMBus v1.3 telemetry of IIN/IOUT/PIN/POUT supports memory-rail health monitoring. Diode emulation and automatic phase add/drop keep efficiency high during DDR self-refresh and idle states. Placed between the 12V bus and the DIMM-side output inductors with per-phase current sense, the controller outperforms analog-only multiphase solutions with adaptive digital transient response.
Recommandé
Server / Datacentre CPU and SoC POL
For server CPU and SoC point-of-load rails in the 80–200 A range, the ISL68222IRAZ in a 5+0 or 4+1 configuration drives external smart power stages with cycle-by-cycle current limiting and adaptive overcurrent protection. The proprietary synthetic current modulation scheme minimizes output capacitor count while delivering fast transient response for load steps typical of compute workloads. AVSBus compliance allows integration into advanced telemetry frameworks used by datacentre power managers. The 40-pin TQFN (5x5) keeps the controller footprint compact next to the power stages, freeing board area for dense compute layouts.
Recommandé
FPGA / ASIC Point-of-Load Supplies
FPGAs and ASICs demand tight-core-rail regulation with fast transient response - the ISL68222IRAZ delivers both via its digital control loop with ±0.5% accuracy and adaptive transient tuning. Configurable switching frequency lets designers trade off efficiency vs ripple for FPGA power-sensitive SerDes rails, while PMBus v1.3 enables firmware-driven VID changes for ASIC dynamic voltage scaling. Two independent outputs (1+1, 2+1) handle core plus auxiliary rails from a single controller, simplifying the BOM. Used widely in networking, telecom, and test-and-measurement equipment that combines an FPGA with a companion ASIC.
Recommandé
Telecom Base-Station Point-of-Load
Telecom base-station boards need robust POL converters for baseband ASICs, FPGAs, and memory. The ISL68222IRAZ's industrial -40C to +85C operating range, extensive fault protection (OCP, OVP, UVP, OTP), and PMBus fault logging make it suitable for outdoor-cabinet telecom equipment. The dual-output flexibility supports both the baseband core and its memory from one controller, reducing component count and board area. Phase add/drop keeps efficiency high during idle periods typical of base-station traffic patterns. Renesas' long-term product support and PMBus configurability simplify compliance with telecom power-management protocols.
Recommandé
High-End Graphics Card / GPU VRM
Discrete GPU and accelerator cards need multiphase VRMs with telemetry - the ISL68222IRAZ supports up to 5 phases with full PMBus telemetry of current, voltage, and power for GPU power-bracket management. The synthetic current modulation scheme provides fast transient response for GPU boost-clock load steps, while diode emulation and automatic phase add/drop keep light-load efficiency high for idle/desktop use cases. The dual-output option lets a single IC power GPU VDD plus memory VDDQ if needed. Configuration via Renesas PowerNavigator accelerates bring-up versus analog-compensation-based controllers.
Recommandé
Industrial Embedded Computing / Edge Server
Edge servers and industrial embedded computing platforms need compact, high-efficiency multiphase POL converters - the ISL68222IRAZ's 40-pin 5x5 TQFN fits dense board layouts while its digital control eliminates analog compensation networks that drift over temperature. Configurable as 3+1, 2+1, or 1+1, it can power a CPU core plus DDR plus auxiliary rail from one controller, lowering BOM cost in space-constrained designs. PMBus v1.3 interface integrates with industrial BMC (baseboard management controller) telemetry stacks, and the -40C to +85C industrial temperature range suits factory and outdoor edge deployments.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL68222IRAZ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL68233IRAZ | ISL68222IRAZ-T |
|---|---|---|---|
| Package | 40-pin TQFN (5x5) | 40-pin TQFN (5x5) - same | 40-pin TQFN (5x5) - same |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Maximum Total Phases | 5 | 5 | 5 |
| Number of Outputs | 2 (X+Y ≤ 5) | 2 (X+Y ≤ 5) | 2 (X+Y ≤ 5) |
| Output Voltage Accuracy | ±0.5% | ±0.5% | ±0.5% |
| Serial Interface | PMBus v1.3 / AVSBus / SMBus | PMBus v1.3 / AVSBus / SMBus | PMBus v1.3 / AVSBus / SMBus |
| Light-Load Efficiency | Diode emulation + auto phase add/drop | Diode emulation + auto phase add/drop | Diode emulation + auto phase add/drop |
| Telemetry | VIN/VOUT/IIN/IOUT/PIN/POUT/TEMP | VIN/VOUT/IIN/IOUT/PIN/POUT/TEMP | VIN/VOUT/IIN/IOUT/PIN/POUT/TEMP |
| Packaging | Tube | Tube (or T/R) | Tape & Reel |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C |
Principaux différenciateurs
- Dual-output flexibility in a single 5-phase controller (vs ISL68236IRAZ-T (9-phase, 52-pin QFN))
- AVSBus compliance for advanced telemetry (vs ISL68222IRAZ-T (T&R variant))
- Synthetic current modulation for adaptive transient response (vs ISL68233IRAZ (firmware-tuning variant))
Notes de conception
Place the ISL68222IRAZ close to its smart power stages (e.g., Renesas ISL99140) to minimize gate-drive trace inductance and current-sense loop area. Keep the per-phase current-sense traces (positive and negative) matched in length and width, and route them as a differential pair to reject common-mode noise. Provide a solid ground plane on layer 2 directly under the 40-pin TQFN thermal pad and stitch it with multiple vias to lower layers for thermal and EMI performance. Decouple the AVIN/PVIN supply pins with 1uF and 0.1uF ceramic capacitors placed as close as possible to the pins.
Avoid using generic I2C pull-up resistors on the PMBus/AVSBus/SMBus lines - consult the datasheet for the recommended pull-up value (typically 2.2k to 4.7k ohms depending on bus capacitance and speed). Do not leave unused PWM outputs floating when configured for fewer phases; tie them to known states per the datasheet. When configuring phase assignments, ensure the firmware (via PowerNavigator) reflects the actual hardware phase wiring - a 3+2 vs 4+1 mismatch can cause catastrophic current sharing errors. Always validate output voltage at the load point, not at the inductor, when using differential remote sense.
The ISL68222IRAZ is a controller (not a power dissipator), so its 40-pin TQFN thermal pad primarily conducts heat from the digital core and gate drivers. Estimated: with 5 active phases driving external MOSFETs at 500 kHz switching frequency, the controller itself typically dissipates under 1 W. A 4-layer PCB with a 1 oz copper inner plane connected to the thermal pad is generally sufficient; for very high ambient temperatures, expand the copper area or add a small thermal via array directly under the exposed pad to inner copper layers.
The PMBus v1.3 / AVSBus interface is sensitive to ringing on rising edges - keep SMBus/PMBus traces short (under 50 mm if possible) and avoid routing them parallel to switching node traces. Place a series resistor (typically 33 ohms) close to the ISL68222IRAZ SMBus/PMBus output pin to dampen reflections if the bus capacitance exceeds 100 pF. For AVSBus, follow the Renesas AVSBus reference design layout for stub length and termination. Decouple AVSBus/PMBus supply pins with a 0.1uF ceramic capacitor placed within 2 mm of the pin.
Informations de conformité
RoHS compliant per Renesas product listings on DigiKey/Mouser. Industrial -40C to +85C operating temperature range. Not AEC-Q100 qualified (this is an industrial/commercial part; for automotive-grade equivalent, consult Renesas).
