ISL83385IA - 250kbps RS-232 Transceiver | Harris
Référence : ISL83385IA ✗ Fin de vieISL83385IA Présentation
An RS-232 transceiver combines a driver and receiver on one integrated circuit. It converts a host controller's logic-level transmit and receive signals into RS-232-compatible levels and converts incoming RS-232 levels back to logic. Within the device hierarchy, the ISL83385IA is an interface IC, a UART-interface component, and a physical-layer RS-232 transceiver used between digital systems and serial cabling.
Key characteristics include a 3 V to 5.5 V supply range, data signaling at up to 250 kbps, low supply current of approximately 1 µA, and ±15 kV ESD protection. These characteristics make the device suitable for low-power instruments, industrial control links, configuration ports, service interfaces, and embedded systems that exchange data over short RS-232 connections.
The transceiver integrates two transmit and two receive channels according to the family description. Integrated level translation allows a low-voltage host processor to communicate with equipment using the voltage levels defined for RS-232. Its low supply current supports compact battery-operated and portable designs, while the 20-SSOP package helps minimize PCB footprint.
Typical installations include industrial machine-to-controller links, laboratory instrument control, point-of-sale equipment, and service or programming ports. Because RS-232 is a single-ended, unbalanced interface, designers should keep cable runs practical, provide suitable grounding, and place protection components where cables enter an enclosure or industrial environment.
When designing the interface, check the logic levels, supply voltage, and cable termination requirements against the manufacturer's pin description and application information. Decoupling capacitors should be placed close to the supply pins, and external protection may still be required for severe conducted-noise or long outdoor cable environments.
This page consolidates the part's RS-232 interface characteristics, package information, procurement guidance, and application-oriented design notes. It also organizes drop-in candidates by electrical proximity so engineers can evaluate replacements before committing a PCB layout to a production design.
Alternatives de remplacement direct pour ISL83385IA — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
ISL83385EIA
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83385E
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83385IA Spécifications
| Product Type | RS-232 Transmitter/Receiver |
| Supply Voltage Range | +3 V to +5.5 V |
| Maximum Data Rate | 250 kbps |
| Courant d'alimentation | Approximately 1 µA |
| ESD Protection | ±15 kV |
| Transmitter Channels | 2 |
| Receiver Channels | 2 |
| Interface Standard | RS-232 |
| Boîtier | 20-SSOP |
| Type de montage | Surface Mount |
| Statut RoHS | unknown |
| REACH Status | unknown |
| Automotive Qualification | not_applicable |
Guide de configuration des broches du ISL83385IA 20-ssop
Configuration des broches du ISL83385IA (boîtier 20-ssop). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ISL83385IA.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ISL83385IA convient pour 6 applications: Industrial Controller Service Port, Laboratory Instrument Control, Embedded Device Configuration Interface, Point-of-Sale and Peripheral Link, Portable Test and Measurement Unit, Battery-Powered Field Sensor Interface.
Industrial Controller Service Port
The ISL83385IA suits a service or configuration port that connects a 3.3 V or 5 V controller to industrial equipment over RS-232. Its 250 kbps capability provides ample margin for short command and response transfers, while approximately 1 µA supply current supports low-power operating states. The 20-SSOP surface-mount package saves board area compared with a larger through-hole arrangement. Confirm the temperature grade and exact pin functions in the manufacturer datasheet, and terminate the cable close to the equipment chassis to reduce stress on the transceiver.
Recommandé
Laboratory Instrument Control
The ISL83385IA can connect laboratory measurement equipment to a host computer or embedded controller when a compact, low-power RS-232 interface is required. Its +3 V to +5.5 V operating range supports modern 3.3 V control electronics, and the 250 kbps maximum data rate is appropriate for short command-and-response protocols. The integrated ±15 kV ESD protection improves handling robustness, although instruments connected to long laboratory leads may benefit from external protection. Use the manufacturer recommended supply capacitance and place it adjacent to the device for reliable operation.
Recommandé
Embedded Device Configuration Interface
The ISL83385IA provides a compact bridge between an embedded controller and a legacy RS-232 configuration port. Its 250 kbps capability is more than sufficient for firmware-upload commands, diagnostic logs, and short parameter exchanges. Approximately 1 µA supply current makes the interface attractive in systems where the main controller sleeps between service operations. The surface-mount 20-SSOP package supports dense controller boards, but the exact enable, shutdown, and fault-reporting functions must be verified from the pin-description table before firmware is written.
Recommandé
Point-of-Sale and Peripheral Link
The ISL83385IA can serve in point-of-sale peripherals, receipt equipment, or service terminals that expose an RS-232 port to a host system. The 250 kbps data rate supports transactional commands and short status exchanges, while its low supply current suits cost-sensitive and space-constrained designs. The +3 V to +5.5 V range allows connection to both legacy 5 V equipment and modern 3.3 V electronics. For cables routed through commercial environments, combine the integrated ESD protection with connector-side surge protection and maintain a low-impedance signal-ground path.
Recommandé
Portable Test and Measurement Unit
A portable tester can use the ISL83385IA to communicate with fixtures or legacy peripherals through a short RS-232 cable. The approximately 1 µA supply current reduces standby burden, while the 250 kbps rate is suitable for binary measurement transfers and setup commands. Its 20-SSOP package leaves more PCB area for sensing, display, and power-management circuitry. Avoid relying only on the integrated ±15 kV ESD rating when a user-accessible connector may receive severe transients; add external protection and provide a stable reference ground.
Recommandé
Battery-Powered Field Sensor Interface
The ISL83385IA is appropriate for a battery-powered field device that periodically exchanges short packets with a service laptop or local controller. The low supply current of approximately 1 µA and the 3 V to +5.5 V range help align the transceiver with rechargeable-cell systems and modern low-power logic. The 250 kbps maximum rate allows rapid burst transfers without requiring a high-bandwidth physical layer. Because field cables can be long and exposed, add connector-side TVS protection, maintain a robust ground reference, and verify the operating-temperature grade in the manufacturer datasheet.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL83385IA — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL83385EIA | ISL83385E |
|---|---|---|---|
| Brand | Harris Corporation | Renesas Electronics Corporation | Intersil Corporation |
| Package | 20-SSOP | 20-SSOP | 20-SSOP |
| Device Type | RS-232 Transmitter/Receiver | 2/2 Transceiver, Full RS-232 | RS-232 Transmitter/Receiver |
| Supply Voltage Range | +3 V to +5.5 V | +3 V to +5.5 V | +3 V to +5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps |
| Supply Current | Approximately 1 µA | Approximately 1 µA | Approximately 1 µA |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV |
| Transmitter Channels | 2 | 2 | 2 |
| Receiver Channels | 2 | 2 | 2 |
Principaux différenciateurs
- Matches the established ISL83385 electrical headline ratings (vs ISL83385EIA)
- Low supply current supports power-conscious interfaces (vs ISL83385E)
- Integrated ESD protection supports robust connector handling (vs ISL83385EIA)
Notes de conception
Place the transceiver supply bypass capacitor directly beside the device power and ground pins, and route the connection with a short, low-impedance path. Keep the RS-232 connector and any external protection network away from sensitive analog or high-speed digital circuits. The small 20-SSOP footprint makes pin-level decoupling and ground-return routing particularly important.
Do not treat an RS-232 transceiver as a differential or long-distance communication solution. Confirm whether the interface includes transmit and receive data pins, shutdown control, and status indications before assigning connector signals. A candidate with the same package is not necessarily interchangeable unless every populated pin has the same electrical function and no connection changes are required.
RS-232 is an unbalanced interface, so cable routing and ground quality determine noise immunity. Keep the cable away from switching power nodes and high-current motor wiring, terminate the interface near the connector, and use a solid chassis or circuit-board ground reference. For exposed industrial cables, add connector-side TVS protection because the integrated ±15 kV ESD rating does not eliminate the need for surge protection.
Informations de conformité
No compliance declarations were identified for this exact orderable MPN. Confirm RoHS, REACH, halogen-free, and conflict-minerals status with the manufacturer before release.