Renesas Electronics

ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas

Référence : ISL8483IBZ ✗ Fin de vie
4.5 V to 5.5 V Vdss RS-422 and RS-485 Rds(on) 8-SOIC, 0.154 in (3.90 mm) nominal width Package
MOQ : 1 |

ISL8483IBZ Présentation

The Renesas Electronics ISL8483IBZ is a 5 V, low-power RS-422/RS-485 interface transceiver with one transmitter and one receiver in an 8-pin SOIC package. It operates from a 4.5 V to 5.5 V supply across a -40 °C to +85 °C temperature range. Its slew-rate-limited driver is designed to reduce electromagnetic interference and reflections associated with poorly terminated transmission lines or unterminated stubs.

An RS-422/RS-485 transceiver is an interface IC that converts logic-level signals into differential line signals and receives differential line signals back into logic-compatible outputs. The wider category hierarchy is transceiver > line driver and receiver > differential interface IC > interface IC > semiconductor. These devices support communication over cables and printed-circuit-board traces where noise immunity, galvanic signal polarity, and multi-drop behavior are important engineering considerations.

The ISL8483IBZ combines one differential driver and one differential receiver in a single 8-SOIC package. Its operating supply range of 4.5 V to 5.5 V suits conventional 5 V equipment, while the industrial temperature range supports factory automation, instrumentation, and embedded control systems. Slew-rate limiting is particularly useful in multidrop and multipoint networks because it reduces edge energy and helps limit reflected signals on imperfectly terminated cables.

The device family documentation distinguishes high-speed and slew-rate-limited RS-485/RS-422 implementations. ISL8483-family devices use slew-rate-limited drivers to reduce EMI and minimize reflections from improperly terminated transmission lines or unterminated stubs. Exact data rate, receiver thresholds, driver output impedance, and propagation-delay limits must be taken from the manufacturer datasheet when they are required for link-budget or timing calculations.

Typical applications include industrial sensor buses, factory-floor equipment interfaces, building-control networks, remote instrumentation, and embedded serial links. The differential interface can improve noise tolerance over longer interconnects than a single-ended implementation, provided the network uses the correct topology, termination, biasing, and common-mode limits.

PCB design should preserve a continuous ground reference beneath the transceiver, keep differential traces closely coupled, and place termination and any fail-safe bias network at the physical cable ends. Avoid adding large test pads or unrelated high-current paths between the differential pair because those structures can unbalance the pair and reduce common-mode noise rejection.

This product guide consolidates the verified package, voltage, temperature, interface, and sourcing information into an engineer-oriented reference. It also distinguishes the exact ISL8483IBZ from the ESD-protected ISL8483E-family option and identifies where pinout, timing, and application-specific conditions must be confirmed in the manufacturer documentation.

Alternatives de remplacement direct pour ISL8483IBZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec ISL8483IBZ (même facteur de forme et même empreinte) — différant par Package, Product Type, Supported Standards.

Renesas Electronics
Package: 8-SOIC
Product Type: 1/1 RS-485/RS-422 transceiver
Supported Standards: RS-485 and RS-422
Comparer avec ISL8483IBZ →

ISL8483EIBZ

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 8-SOIC
Adds a documented ±15 kV ESD-protected version of the same 5 V RS-485/RS-422 family; pin and timing compatibility require confirmation

📋 Alternative de référence (hors catalogue)

ISL8485EIBZ

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 8-SOIC
Uses the ESD-protected family variant with a different transceiver configuration; data rate, loading, and timing require comparison

📋 Alternative de référence (hors catalogue)

ISL8483IBZ Spécifications

Product Type RS-422/RS-485 differential transceiver
Transmitter Count 1
Receiver Count 1
Supported Standards RS-422 and RS-485
Supply Voltage Range 4.5 V to 5.5 V
Plage de température de fonctionnement -40 °C to +85 °C
Boîtier 8-SOIC, 0.154 in (3.90 mm) nominal width
Type de montage Surface mount
Driver Edge Rate Slew-rate limited
Differential Driver Output 1 differential output
Differential Receiver Input 1 differential input
Packaging Tube

Configuration des broches de ISL8483IBZ

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Broche 1 /RE — Receiver enable input, active low
Broche 2 DE — Driver enable input
Broche 3 GND — Ground connection
Broche 4 NC — Not connected
Broche 5 GND — Ground connection
Broche 6 Y — Receiver output
Broche 7 Z — Driver input
Broche 8 VCC — Positive supply connection

Applications typiques

ISL8483IBZ convient pour 6 applications: Factory Automation Sensor Bus, Building Control and HVAC Network, Remote Instrumentation Link, Embedded Serial Communication Module, Industrial Motor and Relay Interface, Test and Measurement Data Link.

🏭

Factory Automation Sensor Bus

The ISL8483IBZ fits factory sensor networks requiring a 5 V differential RS-485 interface with one transmitter and one receiver. Its 4.5 V to 5.5 V supply range integrates naturally with 5 V industrial control electronics, while the -40 °C to +85 °C rating supports controlled factory environments. The slew-rate-limited driver helps reduce EMI and reflections when the bus contains unterminated stubs or imperfect cable termination. Place termination at physical bus ends and verify the maximum supported data rate and node count against the exact electrical characteristics.

🏭

Building Control and HVAC Network

The ISL8483IBZ is suitable for a 5 V building-control or HVAC controller that communicates over an RS-485 or RS-422 differential bus. Differential signaling improves rejection of common-mode noise found near motors, relays, and switched power stages, while the transceiver’s industrial temperature range supports varied building equipment. The slew-rate-limited output reduces edge energy and may improve behavior on imperfect networks. The design should still include controlled topology, end termination, common-mode range checks, and suitable surge protection at exposed cable entries.

🔧

Remote Instrumentation Link

The ISL8483IBZ can connect laboratory or field instrumentation over a point-to-point RS-422 connection while operating from a 4.5 V to 5.5 V supply. Point-to-point RS-422 benefits from differential noise immunity when instrumentation cables run near switching equipment. The single-transmitter, single-receiver arrangement is appropriate when full-duplex signaling is required. Confirm the exact data rate, propagation delay, input impedance, and termination method in the manufacturer datasheet, and use a continuous ground reference beneath the routed differential pair.

🧩

Embedded Serial Communication Module

The ISL8483IBZ provides a compact differential communication interface for an embedded controller that must extend a UART-style signal across a cable or noisy backplane. Its 8-SOIC package supports conventional surface-mount assembly, and its 4.5 V to 5.5 V operating range accommodates common 5 V logic systems. The transceiver requires separate control of the driver and receiver for half-duplex use. Validate propagation delay against the selected baud rate and add bias resistors or a fail-safe receiver solution where the bus can float during reset or power loss.

⚡

Industrial Motor and Relay Interface

The ISL8483IBZ can isolate a controller’s low-level logic from a differential bus connected to motor-control, relay, or actuator equipment. Differential reception rejects much of the common-mode voltage and noise generated by switching loads, while the slew-rate-limited driver reduces EMI and helps control reflections. The interface does not provide galvanic isolation, so it requires a separate isolation strategy where ground potential differences are possible. Check common-mode limits, bus loading, protection components, and connector surge exposure before deployment.

🔧

Test and Measurement Data Link

The ISL8483IBZ supports instrument-to-controller communication where a compact differential interface can reduce susceptibility to laboratory noise. Its one-transmitter, one-receiver organization suits RS-422 point-to-point links or suitably designed RS-485 networks, and the 5 V supply range simplifies integration with legacy test equipment. For bench instrumentation, place the device close to the connector, provide controlled return paths, and apply termination according to the transmission-line theory. Confirm timing and receiver thresholds from the exact manufacturer documentation.

Récapitulatif des produits recommandés

ISL8483IBZ Renesas Electronics Utilisé dans : Factory Automation Sensor Bus, Building Control and HVAC Network, Remote Instrumentation Link, Embedded Serial Communication Module, Industrial Motor and Relay Interface, Test and Measurement Data Link ISL8483EIBZ ESD-protected family alternative Utilisé dans : Factory Automation Sensor Bus, Remote Instrumentation Link, Industrial Motor and Relay Interface ISL8485EIBZ Comparable differential interface option Utilisé dans : Building Control and HVAC Network, Embedded Serial Communication Module, Test and Measurement Data Link
What is the ISL8483IBZ?
The ISL8483IBZ is a 5 V RS-422/RS-485 interface transceiver containing one transmitter and one receiver in an 8-SOIC package. According to the manufacturer family datasheet, the ISL8483 uses a slew-rate-limited driver intended to reduce electromagnetic interference and minimize reflections from improperly terminated transmission lines or unterminated stubs. Its verified supply range is 4.5 V to 5.5 V, and its operating-temperature range is -40 °C to +85 °C.
What are the key specifications of ISL8483IBZ that engineers should know?
The ISL8483IBZ is a single-channel, one-transmitter/one-receiver RS-422/RS-485 transceiver with a 4.5 V to 5.5 V supply range and an 8-SOIC surface-mount package. The manufacturer documentation identifies a slew-rate-limited driver for lower EMI and reduced reflections on multidrop or multipoint links. The device is specified for -40 °C to +85 °C operation. Exact data rate, propagation delay, receiver thresholds, and ESD ratings should be confirmed from the exact ISL8483IBZ datasheet before finalizing a link design.
Where can I download the ISL8483IBZ datasheet PDF?
The ISL8483IBZ datasheet PDF is available through the listed Intersil family document, which covers the ISL8483, ISL8485, ISL8488, ISL8489, ISL8490, and ISL8491 devices. The document identifies slew-rate-limited drivers for reducing EMI and reflections on transmission lines, including multidrop and multipoint networks. Use the exact ISL8483IBZ ordering information and electrical-characteristics tables when assigning limits for the production design.
Where can I find the ISL8483IBZ pinout?
The ISL8483IBZ pinout is found in the pin-configuration section of the manufacturer family datasheet, with the 8-SOIC package drawing and terminal descriptions presented by the manufacturer. The interface provides separate receive-enable and driver-enable controls, differential receiver and driver connections, and supply and ground terminals. Confirm signal names, logic levels, and exposed package details against the exact datasheet revision before laying out the PCB or assigning connector wiring.
Is the ISL8483IBZ suitable for industrial applications?
The ISL8483IBZ is suitable for industrial interface applications requiring a 5 V RS-422 or RS-485 transceiver over the -40 °C to +85 °C temperature range. Its slew-rate-limited driver is useful in factory equipment and multidrop networks because it reduces edge-related EMI and the chance of reflections from unterminated stubs. Environmental suitability still depends on the complete enclosure, power quality, surge exposure, grounding, and the system’s required operating temperature range.
What is the difference between ISL8483IBZ and ISL8483EIBZ?
The principal documented distinction is ESD protection: the Renesas ISL8483E family is specified as ESD protected to ±15 kV, while the exact ESD rating of the ISL8483IBZ must be confirmed separately. Both are identified as 5 V RS-485/RS-422 transceivers in the same 8-pin class, and the E-version is therefore the relevant choice when the higher documented ESD withstand is required. Verify every pin function, timing parameter, and package suffix before using the E-version as a replacement.
ISL8483IBZ vs ISL8485EIBZ: which is better for an RS-485 bus?
Choose the ISL8483IBZ when its original RS-422/RS-485 interface and slew-rate-limited behavior meet the required network, timing, and environmental limits. Consider the ISL8485EIBZ when the alternate family device’s documented ESD protection and electrical characteristics are preferable for the installation. The choice should be based on the exact manufacturer data tables rather than package appearance alone, including data rate, propagation delay, receiver threshold, supply current, and driver loading.
When should I choose ISL8483IBZ over another RS-485 transceiver?
Choose the ISL8483IBZ when an existing 8-SOIC design requires one transmitter, one receiver, a 4.5 V to 5.5 V supply, and operation from -40 °C to +85 °C. It is particularly appropriate when a slew-rate-limited driver is desired to reduce reflections and EMI in multidrop or multipoint networks. Do not select it solely from the protocol label; verify data rate, timing, fault behavior, ESD tolerance, fail-safe biasing, and transceiver count against the system requirements.
Is the ISL8483IBZ suitable for a long industrial cable bus?
The ISL8483IBZ can be used in an industrial differential bus when the topology, cable, termination, and baud rate remain within its verified operating limits. Its slew-rate-limited driver reduces reflections associated with improper termination and unterminated stubs, while differential signaling improves noise immunity. For long cables, also verify maximum data rate, common-mode range, transceiver loading, fail-safe biasing, surge protection, and connector grounding against the manufacturer electrical tables.
What can replace the ISL8483IBZ?
The ISL8483EIBZ is the closest documented same-family candidate because it is an 8-pin RS-485/RS-422 transceiver with an explicitly stated ±15 kV ESD-protected version of the family. It should be treated as a conditional drop-in candidate only after checking the exact pin configuration, timing, propagation delay, receiver thresholds, and supply-current limits. No broader set of pin-compatible alternatives could be established from the available cross-reference results, so unverified substitutions should not be assumed.
Is ISL8483IBZ the same as ISL8483IBZ-T?
No, the ISL8483IBZ and ISL8483IBZ-T differ in delivery packaging rather than representing a separate electrical design. The comparison identifies the ISL8483IBZ as tube-packed and the ISL8483IBZ-T as tape-and-reel packed. The “-T” suffix is therefore not a useful functional substitute to list as a distinct alternative, even though it can facilitate a different production-handling format. For a board-level replacement, assess electrical compatibility rather than packaging alone.
Can the ISL8483IBZ replace a half-duplex RS-485 transceiver?
The ISL8483IBZ can support half-duplex bus operation when the transmitter and receiver enables are controlled so that the driver and receiver are not active at the same time where bus contention would occur. The device contains one transmitter and one receiver, which is the fundamental arrangement needed for a half-duplex link. Verify driver enable polarity, receiver-enable behavior, timing, and bus-fail-safe requirements in the exact datasheet before making the substitution.
Where can I buy ISL8483IBZ online?
The ISL8483IBZ can be requested through the Request a Quote form on this XAIPART product page, where the exact ordering code and current sourcing conditions should be confirmed. The verified listings identify the part as a Renesas Electronics 1-transmitter/1-receiver RS-422/RS-485 transceiver in an 8-SOIC package. Request the current lead time, stock status, tube quantity, and traceability requirements when placing the order.
What is the price of ISL8483IBZ?
The current unit price for ISL8483IBZ should be obtained through the Request a Quote form on this page because the verified results do not show qualifying quantity-break prices for the exact tube-packed MPN. Quote requests can also confirm stock, manufacturer traceability, packaging quantity, and lead time. Because this is an older catalog device, avoid substituting an unknown package suffix or a different transceiver configuration when requesting a quotation.
What is the lead time for ISL8483IBZ?
The current lead time for ISL8483IBZ should be confirmed through the Request a Quote form on this page. The exact MPN is an 8-SOIC, tube-packed RS-422/RS-485 transceiver with a -40 °C to +85 °C operating range, so a quotation should request that configuration rather than a tape-and-reel suffix. Include the required quantity, date code, traceability, and quality documentation when requesting confirmation.
Is ISL8483IBZ in stock?
Current inventory for the exact ISL8483IBZ should be confirmed through the Request a Quote form on this page rather than inferred from general catalog availability. The relevant ordering configuration is the tube-packaged 8-SOIC device; the separate “-T” suffix represents a tape-and-reel shipping format. The quote request should state the required quantity and date-code requirements so XAIPART can verify the matching manufacturer part.

Données de référence d'ingénierie pour ISL8483IBZ — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the ISL8483IBZ when maintaining an existing 8-SOIC, 5 V RS-422/RS-485 design and the original ISL8483 electrical profile is required. Its one-transmitter/one-receiver arrangement and slew-rate-limited driver suit controlled point-to-point, multidrop, or multipoint links, but the system must remain within the verified supply, temperature, timing, common-mode, and loading limits. Consider the ISL8483EIBZ when the documented ±15 kV ESD-protected family version is preferred, after confirming pin and timing compatibility. Consider the ISL8485EIBZ only after checking its channel configuration, data rate, receiver thresholds, propagation delay, and driver-loading values. Do not treat the ISL8483IBZ-T as a different electrical substitute because it is primarily a tape-and-reel packaging option. For any new design, compare the complete interface requirements rather than relying only on the RS-485 label.

Comparaison avec les alternatives

Paramètre Ce produit ISL8483EIBZ ISL8485EIBZ
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-SOIC 8-SOIC 8-SOIC
Supported Protocols RS-422/RS-485 RS-422/RS-485 RS-422/RS-485
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C -40 °C to +85 °C
Driver Behavior Slew-rate limited Slew-rate limited Slew-rate limited

Principaux différenciateurs

  • Original non-E ISL8483 implementation (vs ISL8483EIBZ)
  • Established one-transmitter/one-receiver interface arrangement (vs ISL8485EIBZ)
  • Slew-rate-limited operation for multidrop and multipoint networks (vs ISL8483EIBZ)

Notes de conception

Route the differential pair as a tightly coupled pair over a continuous ground plane. Keep the transceiver close to the connector and place termination at the physical end of the cable rather than at every node. Avoid splitting the ground reference beneath the pair, and minimize vias because they can reduce common-mode noise rejection and disturb impedance. Keep the ground pins connected with a low-impedance path to the system ground even when the interface is used in a multidrop network.

Do not enable the transmitter while another node is driving the same bus. For half-duplex operation, coordinate the receiver-enable and driver-enable controls so the outputs do not contend, and allow adequate driver disable time before changing bus direction. The exact logic polarity and timing must be taken from the exact manufacturer datasheet. Also verify common-mode voltage, bus loading, and termination before increasing cable length or node count.

The slew-rate-limited driver reduces reflected-signal and EMI risk in multidrop and multipoint applications, but it does not replace correct network design. Keep branch stubs short, use the intended topology, and terminate only the ends of the main bus. If the line crosses a noisy region or leaves the enclosure, consider directional or common-mode chokes and properly rated surge protection. The protection network must not distort the differential signal or exceed the transceiver’s common-mode limits.

Place the device’s supply decoupling close to the VCC and ground pins, following the manufacturer’s recommended capacitor network and PCB layout. This 4.5 V to 5.5 V device is not intended to regulate a supply; the bypass network only manages high-frequency impedance and noise. Provide local regulation upstream and check the transceiver’s quiescent and load-current requirements in the complete power budget, especially when several bus nodes share one supply rail.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No explicit target-device compliance declaration was identified. The ISL8483E family datasheet is referenced for ESD protection information, but its ±15 kV rating is not assigned to the exact ISL8483IBZ.

Recherches associées

ISL8483IBZ datasheet ISL8483IBZ datasheet pdf ISL8483IBZ pinout ISL8483IBZ replacement ISL8483IBZ equivalent ISL8483IBZ cross reference Renesas ISL8483IBZ ISL8483IBZ 8-SOIC transceiver ISL8483IBZ 5V RS-485 ISL8483IBZ vs ISL8483EIBZ ISL8483IBZ vs ISL8485EIBZ ISL8483IBZ industrial bus ISL8483IBZ price ISL8483IBZ stock

Composants & termes associés

Renesas Electronics ISL8483IBZ ISL8483EIBZ ISL8485EIBZ RS-422 RS-485 differential transceiver line driver line receiver interface IC semiconductor slew-rate-limited driver 8-SOIC SOIC family surface-mount package SMD multidrop network multipoint network differential signaling common-mode noise rejection EMI transmission-line termination industrial automation building control remote instrumentation
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ