ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas
MPN: ISL8483IBZ ✗ Cuối đờiISL8483IBZ Tóm tắt
An RS-422/RS-485 transceiver is an interface IC that converts logic-level signals into differential line signals and receives differential line signals back into logic-compatible outputs. The wider category hierarchy is transceiver > line driver and receiver > differential interface IC > interface IC > semiconductor. These devices support communication over cables and printed-circuit-board traces where noise immunity, galvanic signal polarity, and multi-drop behavior are important engineering considerations.
The ISL8483IBZ combines one differential driver and one differential receiver in a single 8-SOIC package. Its operating supply range of 4.5 V to 5.5 V suits conventional 5 V equipment, while the industrial temperature range supports factory automation, instrumentation, and embedded control systems. Slew-rate limiting is particularly useful in multidrop and multipoint networks because it reduces edge energy and helps limit reflected signals on imperfectly terminated cables.
The device family documentation distinguishes high-speed and slew-rate-limited RS-485/RS-422 implementations. ISL8483-family devices use slew-rate-limited drivers to reduce EMI and minimize reflections from improperly terminated transmission lines or unterminated stubs. Exact data rate, receiver thresholds, driver output impedance, and propagation-delay limits must be taken from the manufacturer datasheet when they are required for link-budget or timing calculations.
Typical applications include industrial sensor buses, factory-floor equipment interfaces, building-control networks, remote instrumentation, and embedded serial links. The differential interface can improve noise tolerance over longer interconnects than a single-ended implementation, provided the network uses the correct topology, termination, biasing, and common-mode limits.
PCB design should preserve a continuous ground reference beneath the transceiver, keep differential traces closely coupled, and place termination and any fail-safe bias network at the physical cable ends. Avoid adding large test pads or unrelated high-current paths between the differential pair because those structures can unbalance the pair and reduce common-mode noise rejection.
This product guide consolidates the verified package, voltage, temperature, interface, and sourcing information into an engineer-oriented reference. It also distinguishes the exact ISL8483IBZ from the ESD-protected ISL8483E-family option and identifies where pinout, timing, and application-specific conditions must be confirmed in the manufacturer documentation.
Bộ thay thế dễ dàng lắp đặt cho ISL8483IBZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL8483IBZ (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Supported Standards.
ISL8483EIBZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8485EIBZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8483IBZ Thông số kỹ thuật
| Product Type | RS-422/RS-485 differential transceiver |
| Transmitter Count | 1 |
| Receiver Count | 1 |
| Supported Standards | RS-422 and RS-485 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 8-SOIC, 0.154 in (3.90 mm) nominal width |
| Kiểu lắp đặt | Surface mount |
| Driver Edge Rate | Slew-rate limited |
| Differential Driver Output | 1 differential output |
| Differential Receiver Input | 1 differential input |
| Packaging | Tube |
Cấu hình chân ISL8483IBZ
| Chân 1 | /RE — Receiver enable input, active low |
| Chân 2 | DE — Driver enable input |
| Chân 3 | GND — Ground connection |
| Chân 4 | NC — Not connected |
| Chân 5 | GND — Ground connection |
| Chân 6 | Y — Receiver output |
| Chân 7 | Z — Driver input |
| Chân 8 | VCC — Positive supply connection |
Ứng dụng tiêu biểu
ISL8483IBZ phù hợp cho 6 Áp dụngs: Factory Automation Sensor Bus, Building Control and HVAC Network, Remote Instrumentation Link, Embedded Serial Communication Module, Industrial Motor and Relay Interface, Test and Measurement Data Link.
Factory Automation Sensor Bus
The ISL8483IBZ fits factory sensor networks requiring a 5 V differential RS-485 interface with one transmitter and one receiver. Its 4.5 V to 5.5 V supply range integrates naturally with 5 V industrial control electronics, while the -40 °C to +85 °C rating supports controlled factory environments. The slew-rate-limited driver helps reduce EMI and reflections when the bus contains unterminated stubs or imperfect cable termination. Place termination at physical bus ends and verify the maximum supported data rate and node count against the exact electrical characteristics.
Được đề xuất
Building Control and HVAC Network
The ISL8483IBZ is suitable for a 5 V building-control or HVAC controller that communicates over an RS-485 or RS-422 differential bus. Differential signaling improves rejection of common-mode noise found near motors, relays, and switched power stages, while the transceiver’s industrial temperature range supports varied building equipment. The slew-rate-limited output reduces edge energy and may improve behavior on imperfect networks. The design should still include controlled topology, end termination, common-mode range checks, and suitable surge protection at exposed cable entries.
Được đề xuất
Remote Instrumentation Link
The ISL8483IBZ can connect laboratory or field instrumentation over a point-to-point RS-422 connection while operating from a 4.5 V to 5.5 V supply. Point-to-point RS-422 benefits from differential noise immunity when instrumentation cables run near switching equipment. The single-transmitter, single-receiver arrangement is appropriate when full-duplex signaling is required. Confirm the exact data rate, propagation delay, input impedance, and termination method in the manufacturer datasheet, and use a continuous ground reference beneath the routed differential pair.
Được đề xuất
Embedded Serial Communication Module
The ISL8483IBZ provides a compact differential communication interface for an embedded controller that must extend a UART-style signal across a cable or noisy backplane. Its 8-SOIC package supports conventional surface-mount assembly, and its 4.5 V to 5.5 V operating range accommodates common 5 V logic systems. The transceiver requires separate control of the driver and receiver for half-duplex use. Validate propagation delay against the selected baud rate and add bias resistors or a fail-safe receiver solution where the bus can float during reset or power loss.
Được đề xuất
Industrial Motor and Relay Interface
The ISL8483IBZ can isolate a controller’s low-level logic from a differential bus connected to motor-control, relay, or actuator equipment. Differential reception rejects much of the common-mode voltage and noise generated by switching loads, while the slew-rate-limited driver reduces EMI and helps control reflections. The interface does not provide galvanic isolation, so it requires a separate isolation strategy where ground potential differences are possible. Check common-mode limits, bus loading, protection components, and connector surge exposure before deployment.
Được đề xuất
Test and Measurement Data Link
The ISL8483IBZ supports instrument-to-controller communication where a compact differential interface can reduce susceptibility to laboratory noise. Its one-transmitter, one-receiver organization suits RS-422 point-to-point links or suitably designed RS-485 networks, and the 5 V supply range simplifies integration with legacy test equipment. For bench instrumentation, place the device close to the connector, provide controlled return paths, and apply termination according to the transmission-line theory. Confirm timing and receiver thresholds from the exact manufacturer documentation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ISL8483IBZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISL8483EIBZ | ISL8485EIBZ |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Protocols | RS-422/RS-485 | RS-422/RS-485 | RS-422/RS-485 |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Driver Behavior | Slew-rate limited | Slew-rate limited | Slew-rate limited |
Bảo phân biệt quan trọng
- Original non-E ISL8483 implementation (vsISL8483EIBZ)
- Established one-transmitter/one-receiver interface arrangement (vsISL8485EIBZ)
- Slew-rate-limited operation for multidrop and multipoint networks (vsISL8483EIBZ)
Ghi chú thiết kế
Route the differential pair as a tightly coupled pair over a continuous ground plane. Keep the transceiver close to the connector and place termination at the physical end of the cable rather than at every node. Avoid splitting the ground reference beneath the pair, and minimize vias because they can reduce common-mode noise rejection and disturb impedance. Keep the ground pins connected with a low-impedance path to the system ground even when the interface is used in a multidrop network.
Do not enable the transmitter while another node is driving the same bus. For half-duplex operation, coordinate the receiver-enable and driver-enable controls so the outputs do not contend, and allow adequate driver disable time before changing bus direction. The exact logic polarity and timing must be taken from the exact manufacturer datasheet. Also verify common-mode voltage, bus loading, and termination before increasing cable length or node count.
The slew-rate-limited driver reduces reflected-signal and EMI risk in multidrop and multipoint applications, but it does not replace correct network design. Keep branch stubs short, use the intended topology, and terminate only the ends of the main bus. If the line crosses a noisy region or leaves the enclosure, consider directional or common-mode chokes and properly rated surge protection. The protection network must not distort the differential signal or exceed the transceiver’s common-mode limits.
Place the device’s supply decoupling close to the VCC and ground pins, following the manufacturer’s recommended capacitor network and PCB layout. This 4.5 V to 5.5 V device is not intended to regulate a supply; the bypass network only manages high-frequency impedance and noise. Provide local regulation upstream and check the transceiver’s quiescent and load-current requirements in the complete power budget, especially when several bus nodes share one supply rail.
Thông tin tuân thủ
No explicit target-device compliance declaration was identified. The ISL8483E family datasheet is referenced for ESD protection information, but its ±15 kV rating is not assigned to the exact ISL8483IBZ.