LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics
Référence : LM2901Q4T ✓ ActifLM2901Q4T Présentation
A voltage comparator is an analog mixed-signal IC that evaluates two input voltages and changes its output when the difference crosses a defined threshold. The comparator category belongs to the broader interface IC and signal-conditioning hierarchy. Open-collector outputs permit several comparator outputs to share a wired bus when an external pull-up is present, making quad comparators useful for monitoring four independent signals in one compact device.
The LM2901Q4T combines four independent comparison channels with very low supply current of 1.1 mA, input offset voltage of 1 mV, input bias current of 25 nA, and response times of 1.3 microseconds. Its rail-to-rail input capability lets each channel operate across the supply range. The operating-temperature range of -40°C to +125°C supports industrial and extended-temperature equipment, while the 3 mm by 3 mm QFN-16-EP package reduces board area compared with larger quad comparator packages.
Each open-collector output can sink current while remaining in a high-impedance state when inactive. This architecture requires a pull-up resistor to establish a logic-high voltage. Because the output transistor can remain off, several channels may be connected to a common bus only when their wired-collector behavior and application logic are compatible. Input and output timing should be evaluated together when detecting slow crossings, short pulses, or noisy thresholds.
Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, sensor threshold conditioning, window comparison, power-supply sequencing, and four-channel logic-level translation. The 2 V to 36 V supply range is particularly useful when the comparator must monitor signals above a conventional 5 V logic rail while operating from a higher system supply.
For PCB design, place bypass capacitance close to the supply pins and route the exposed pad to a thermal copper area according to the manufacturer land pattern. Keep sensitive inverting and non-inverting traces short, avoid routing them beside high-current switching paths, and select the external output pull-up to establish the required logic-high level and sink-current margin.
This product page combines exact electrical and package attributes, application-specific engineering guidance, threshold-level design notes, and a parameter comparison framework. It also distinguishes confirmed drop-in replacements from functionally similar devices whose channel count, package, or electrical behavior prevents direct PCB substitution.
Alternatives de remplacement direct pour LM2901Q4T — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesLM2901Q4T Valeurs maximales et caractéristiques électriques
| Comparator Type | General-purpose low-power voltage comparator |
| Number of Channels | 4 channels |
| Single-Supply Voltage Range | 2 V to 36 V |
| Dual-Supply Voltage Range | ±1 V to ±18 V |
| Courant d'alimentation | 1.1 mA |
| Power per Comparator at 5 V | 1.4 mW |
| Input Offset Voltage | 1 mV |
| Input Bias Current | 25 nA |
| Input Offset Current | 5 nA |
| Propagation Delay | 1.3 microseconds |
| Type de sortie | Open-collector |
| Logic Compatibility | CMOS, DTL, TTL, MOS, and ECL |
| Input Common-Mode Range | Rail-to-rail input |
| Plage de température de fonctionnement | -40°C to +125°C |
| Boîtier | 16-QFN-EP (3 mm by 3 mm) |
| Type de montage | Surface mount |
| Statut RoHS | Compliant |
| Output Pull-Up Requirement | External pull-up resistor required |
| Absolute Maximum Supply Voltage | 36 V |
| Exposed Pad | Present |
Guide de configuration des broches du LM2901Q4T 16-qfn-ep (3 mm by 3 mm)
Configuration des broches du LM2901Q4T (boîtier 16-qfn-ep (3 mm by 3 mm)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LM2901Q4T.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LM2901Q4T convient pour 6 applications: Industrial Overvoltage Detection, Power-Supply Sequencing, Sensor Threshold Conditioning, Window Comparison, Battery Monitoring, Logic-Level Compatibility.
Industrial Overvoltage Detection
The LM2901Q4T is suitable for monitoring several industrial supply rails in one compact package. Each of its four channels can compare a divided voltage against a reference, with 1 mV input offset voltage supporting threshold decisions close to the reference value. The 2 V to 36 V operating range allows channels to monitor signals above conventional 5 V logic levels. Use the open-collector outputs with suitable pull-up resistors, and account for the 1.3 microsecond response time when detecting fast transients.
Recommandé
Power-Supply Sequencing
The four independent LM2901Q4T channels can supervise separate supply rails and indicate their relative status to a controller. Each comparator output provides an open-collector signal that can be pulled up to the logic voltage used by the sequencing controller. With 1.1 mA supply current, the device adds little continuous overhead to a multi-rail system, while rail-to-rail inputs help compare signals near either supply rail. The 3 mm by 3 mm package also reduces the area required for four supervision channels.
Recommandé
Sensor Threshold Conditioning
The LM2901Q4T can condition four independent sensor outputs by comparing each analog level against a local threshold. Its 25 nA input bias current limits loading on high-impedance sensors, and the 1 mV offset specification defines the nominal precision of the comparison around the reference. Four channels allow a compact implementation of temperature, level, pressure, or position sensing. Place sensitive input traces away from switching nodes and choose reference and feedback components with tolerances appropriate to the required threshold accuracy.
Recommandé
Window Comparison
A window comparator can be implemented by using two LM2901Q4T channels, one for the upper threshold and one for the lower threshold. This approach is useful when a monitored voltage must remain between two limits. The device's four-channel capacity leaves two channels available for additional measurements in the same design. Because the outputs are open collector, pull-ups define the logic-high state and permit interface with compatible CMOS or TTL systems. Input filtering and hysteresis should be added when the monitored signal crosses the limits repeatedly.
Recommandé
Battery Monitoring
The LM2901Q4T can monitor four battery-related voltages, such as individual cells, a pack terminal, or charger status signals, when the sensed levels remain within its supported operating conditions. Its low 1.1 mA supply current reduces consumption in continuously monitored equipment, and the broad 2 V to 36 V range accommodates many industrial battery packs. Resistor-divider ratios must keep every input within the device's absolute limits, and channel output states should be checked during battery isolation or reverse-polarity events.
Recommandé
Logic-Level Compatibility
The LM2901Q4T can compare external logic signals against a local reference and drive CMOS, TTL, DTL, MOS, or ECL-compatible receiver stages through open-collector outputs. This makes the device useful in equipment that combines higher-voltage sensing with lower-voltage digital control. Each output requires a pull-up, and the pull-up voltage determines the resulting high level rather than the comparator supply alone. Confirm sink-current requirements and logic thresholds in the receiver datasheet before finalizing the interface.
Recommandé
Données de référence d'ingénierie pour LM2901Q4T — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Brand | STMicroelectronics |
| Package | 16-QFN-EP (3 mm by 3 mm) |
| Comparator Channels | 4 channels |
| Single-Supply Voltage Range | 2 V to 36 V |
| Dual-Supply Voltage Range | ±1 V to ±18 V |
| Supply Current | 1.1 mA |
| Input Offset Voltage | 1 mV |
| Input Bias Current | 25 nA |
| Propagation Delay | 1.3 microseconds |
| Output Type | Open-collector |
| Operating Temperature Range | -40°C to +125°C |
| Logic Compatibility | CMOS, DTL, TTL, MOS, and ECL |
Principaux différenciateurs
- Four independent monitoring channels in one package (vs TLV3701)
- Broader single-supply operating range (vs MCP6541)
- Open-collector output architecture (vs Push-pull comparator)
Notes de conception
Each open-collector output requires an external pull-up resistor. Select the resistor so the pull-up voltage establishes the required logic-high level while providing adequate sink-current margin for the receiving gate and any wired-collector load. Avoid making the pull-up resistance unnecessarily low, because the output must continuously dissipate current during a low output state. When multiple outputs share a bus, verify that every attached channel can safely enter the high-impedance state during normal operation.
The 16-QFN-EP package includes an exposed thermal pad that should be connected to a copper area on the PCB. Follow the manufacturer land pattern and thermal-via recommendation rather than relying on the nominal package size alone. Although the device has a 1.1 mA supply-current specification, sustained output sinking and elevated ambient temperature still create thermal conditions that should be checked against the manufacturer junction-temperature limit.
Keep the inverting and non-inverting input routes short and place them away from high-current switching traces and inductors. Connect the supply bypass capacitor directly to the appropriate supply pins with a minimal return path, and route the exposed pad to the thermal copper plane without creating accidental connections to sensitive input nets. Differential pairs are not normally required, but matched routing and a quiet reference node can reduce threshold variation.
Do not treat the similar LM2902Q4T as a pin-compatible substitute solely because both use a compact 16-QFN format; the LM2902 family is an operational-amplifier product, not the same comparator function. Also do not assume that an open-collector output reaches a valid logic-high voltage when the comparator is inactive. The output remains high impedance until the external pull-up establishes the high state, and input voltages must remain within the datasheet limits during power transitions.
Informations de conformité
The manufacturer product listing identifies the LM2901Q4T as RoHS compliant. No separate qualification claims for REACH, AEC-Q100, halogen-free status, lead-free status, or conflict-minerals reporting were identified.