STMicroelectronics

LM2901Q4T - 4-Channel Low-Power Comparator | STMicroelectronics

料号: LM2901Q4T ✓ 量产中
2 V to 36 V Vdss 1.1 mA Id 16-QFN-EP (3 mm by 3 mm) Package
最小起订量: 1 |

LM2901Q4T 概述

The STMicroelectronics LM2901Q4T is a four-channel low-power voltage comparator with a 2 V to 36 V single-supply range, support for ±1 V to ±18 V dual supplies, and a 16-QFN exposed-pad package measuring 3 mm by 3 mm. Each of its four channels compares an inverting input with a non-inverting input and supports open-collector output operation compatible with CMOS, DTL, TTL, MOS, and ECL logic families.

A voltage comparator is an analog mixed-signal IC that evaluates two input voltages and changes its output when the difference crosses a defined threshold. The comparator category belongs to the broader interface IC and signal-conditioning hierarchy. Open-collector outputs permit several comparator outputs to share a wired bus when an external pull-up is present, making quad comparators useful for monitoring four independent signals in one compact device.

The LM2901Q4T combines four independent comparison channels with very low supply current of 1.1 mA, input offset voltage of 1 mV, input bias current of 25 nA, and response times of 1.3 microseconds. Its rail-to-rail input capability lets each channel operate across the supply range. The operating-temperature range of -40°C to +125°C supports industrial and extended-temperature equipment, while the 3 mm by 3 mm QFN-16-EP package reduces board area compared with larger quad comparator packages.

Each open-collector output can sink current while remaining in a high-impedance state when inactive. This architecture requires a pull-up resistor to establish a logic-high voltage. Because the output transistor can remain off, several channels may be connected to a common bus only when their wired-collector behavior and application logic are compatible. Input and output timing should be evaluated together when detecting slow crossings, short pulses, or noisy thresholds.

Typical uses include industrial control and monitoring, overvoltage and undervoltage detection, sensor threshold conditioning, window comparison, power-supply sequencing, and four-channel logic-level translation. The 2 V to 36 V supply range is particularly useful when the comparator must monitor signals above a conventional 5 V logic rail while operating from a higher system supply.

For PCB design, place bypass capacitance close to the supply pins and route the exposed pad to a thermal copper area according to the manufacturer land pattern. Keep sensitive inverting and non-inverting traces short, avoid routing them beside high-current switching paths, and select the external output pull-up to establish the required logic-high level and sink-current margin.

This product page combines exact electrical and package attributes, application-specific engineering guidance, threshold-level design notes, and a parameter comparison framework. It also distinguishes confirmed drop-in replacements from functionally similar devices whose channel count, package, or electrical behavior prevents direct PCB substitution.

直接替换替代料: LM2901Q4T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

该产品暂无直接替换替代料。

请求替代料

LM2901Q4T 最大额定值与电气特性

Comparator Type General-purpose low-power voltage comparator
Number of Channels 4 channels
Single-Supply Voltage Range 2 V to 36 V
Dual-Supply Voltage Range ±1 V to ±18 V
电源电流 1.1 mA
Power per Comparator at 5 V 1.4 mW
Input Offset Voltage 1 mV
Input Bias Current 25 nA
Input Offset Current 5 nA
Propagation Delay 1.3 microseconds
输出类型 Open-collector
Logic Compatibility CMOS, DTL, TTL, MOS, and ECL
Input Common-Mode Range Rail-to-rail input
工作温度范围 -40°C to +125°C
封装 16-QFN-EP (3 mm by 3 mm)
安装类型 Surface mount
RoHS 状态 Compliant
Output Pull-Up Requirement External pull-up resistor required
Absolute Maximum Supply Voltage 36 V
Exposed Pad Present

LM2901Q4T 16-qfn-ep (3 mm by 3 mm) 引脚配置指南

LM2901Q4T(16-qfn-ep (3 mm by 3 mm) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

LM2901Q4T 的 16-qfn-ep (3 mm by 3 mm) 封装引脚图

暂无详细引脚数据: LM2901Q4T.

请参阅 数据手册 以查看完整引脚配置。

典型应用

LM2901Q4T 适用于 6 应用s: Industrial Overvoltage Detection, Power-Supply Sequencing, Sensor Threshold Conditioning, Window Comparison, Battery Monitoring, Logic-Level Compatibility.

🏭

Industrial Overvoltage Detection

The LM2901Q4T is suitable for monitoring several industrial supply rails in one compact package. Each of its four channels can compare a divided voltage against a reference, with 1 mV input offset voltage supporting threshold decisions close to the reference value. The 2 V to 36 V operating range allows channels to monitor signals above conventional 5 V logic levels. Use the open-collector outputs with suitable pull-up resistors, and account for the 1.3 microsecond response time when detecting fast transients.

⚡

Power-Supply Sequencing

The four independent LM2901Q4T channels can supervise separate supply rails and indicate their relative status to a controller. Each comparator output provides an open-collector signal that can be pulled up to the logic voltage used by the sequencing controller. With 1.1 mA supply current, the device adds little continuous overhead to a multi-rail system, while rail-to-rail inputs help compare signals near either supply rail. The 3 mm by 3 mm package also reduces the area required for four supervision channels.

🧩

Sensor Threshold Conditioning

The LM2901Q4T can condition four independent sensor outputs by comparing each analog level against a local threshold. Its 25 nA input bias current limits loading on high-impedance sensors, and the 1 mV offset specification defines the nominal precision of the comparison around the reference. Four channels allow a compact implementation of temperature, level, pressure, or position sensing. Place sensitive input traces away from switching nodes and choose reference and feedback components with tolerances appropriate to the required threshold accuracy.

📺

Window Comparison

A window comparator can be implemented by using two LM2901Q4T channels, one for the upper threshold and one for the lower threshold. This approach is useful when a monitored voltage must remain between two limits. The device's four-channel capacity leaves two channels available for additional measurements in the same design. Because the outputs are open collector, pull-ups define the logic-high state and permit interface with compatible CMOS or TTL systems. Input filtering and hysteresis should be added when the monitored signal crosses the limits repeatedly.

⚡

Battery Monitoring

The LM2901Q4T can monitor four battery-related voltages, such as individual cells, a pack terminal, or charger status signals, when the sensed levels remain within its supported operating conditions. Its low 1.1 mA supply current reduces consumption in continuously monitored equipment, and the broad 2 V to 36 V range accommodates many industrial battery packs. Resistor-divider ratios must keep every input within the device's absolute limits, and channel output states should be checked during battery isolation or reverse-polarity events.

🔧

Logic-Level Compatibility

The LM2901Q4T can compare external logic signals against a local reference and drive CMOS, TTL, DTL, MOS, or ECL-compatible receiver stages through open-collector outputs. This makes the device useful in equipment that combines higher-voltage sensing with lower-voltage digital control. Each output requires a pull-up, and the pull-up voltage determines the resulting high level rather than the comparator supply alone. Confirm sink-current requirements and logic thresholds in the receiver datasheet before finalizing the interface.

What is the LM2901Q4T and what are its main specifications?
The STMicroelectronics LM2901Q4T is a four-channel, low-power, open-collector voltage comparator designed for operation from 2 V to 36 V. Its key specifications include 1.1 mA supply current, 1 mV input offset voltage, 25 nA input bias current, 1.3 microsecond propagation delay, and a -40°C to +125°C temperature range. The manufacturer lists the device in a 16-QFN-EP package measuring 3 mm by 3 mm.
What supply voltage can the LM2901Q4T use?
The LM2901Q4T can operate from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. This unusually broad operating range allows it to monitor signals beyond 5 V while remaining compatible with lower-voltage systems. According to the manufacturer datasheet, the maximum listed absolute supply voltage is 36 V, so the supply must not exceed that limit under any operating condition.
How many comparators are integrated into the LM2901Q4T?
The LM2901Q4T integrates four independent comparator channels in one package. Each channel has its own pair of differential inputs and open-collector output, allowing four separate threshold measurements to be performed simultaneously. The four-channel arrangement reduces package count and board space compared with four individual comparator ICs while preserving separate output states for each monitored signal.
What is the response time of the LM2901Q4T?
The LM2901Q4T has a listed propagation delay of 1.3 microseconds. This response time is suitable for general-purpose threshold detection, power monitoring, and industrial control functions that do not require the sub-microsecond timing of a dedicated high-speed comparator. The manufacturer datasheet should be consulted for the exact test conditions associated with the delay specification.
Does the LM2901Q4T need an output pull-up resistor?
Yes, each open-collector output on the LM2901Q4T requires an external pull-up resistor to produce a logic-high voltage. The output transistor actively sinks current when the comparison state calls for a low output, but it otherwise remains in a high-impedance state. Select the pull-up resistor and logic supply so the output remains compatible with the connected CMOS, TTL, DTL, MOS, or ECL circuit.
Where can I download the LM2901Q4T datasheet PDF?
The LM2901Q4T datasheet PDF is available from the manufacturer documentation listing and through the linked technical document page. The manufacturer describes the device as a low-power quad voltage comparator, while the document index identifies the LM2901Q4T data sheet as a 17-page PDF. Use the manufacturer version for final electrical characteristics, pin descriptions, and recommended land-pattern details.
Where can I find the LM2901Q4T pinout?
The LM2901Q4T pinout is found in the manufacturer datasheet and must be matched to the 16-QFN-EP land pattern before PCB routing. The package is a compact 3 mm by 3 mm QFN with an exposed pad, so thermal-pad connection and paste-layout details are as important as the numbered signal assignments. Do not infer the pinout from another LM2901 package because exposed-pad and lead configurations can differ.
Is the LM2901Q4T suitable for industrial temperature applications?
The LM2901Q4T is suitable for extended industrial environments because its specified operating-temperature range is -40°C to +125°C. Its wide 2 V to 36 V supply range also supports industrial monitoring circuits that operate above low-voltage logic levels. Temperature derating, input limits, and exposed-pad thermal performance must still be evaluated for the final board and enclosure.
How does the LM2901Q4T compare with a single-channel comparator?
The LM2901Q4T integrates four open-collector comparison channels into one 16-QFN-EP package, while single-channel devices use one comparison channel and therefore require a different package and pinout. A single-channel part can reduce cost when only one threshold function is needed, but the LM2901Q4T simplifies four-monitor designs by reducing component count and providing four independent outputs within one package.
When should I choose the LM2901Q4T instead of a single-channel comparator?
Choose the LM2901Q4T when the design requires four independent voltage comparisons in one compact package. Its four channels can monitor separate supply rails, sensor thresholds, or control signals without using four single-channel ICs. Select a single-channel comparator instead when the design has only one comparison function and needs a lower-cost or smaller-footprint package.
What is the best drop-in replacement for the LM2901Q4T?
No drop-in replacement for the LM2901Q4T can be confirmed from the available manufacturer and distributor documentation. The LM2902Q4T has a similar 16-QFN package family, but it is a quad operational amplifier rather than a quad comparator, so package similarity alone does not establish pin-to-pin compatibility. Treat TLV3701 and MCP6541 as functionally related single-channel comparators, not direct PCB replacements, and verify a proposed substitute against both pinout and electrical requirements.
Can a TLV3701 or MCP6541 replace the LM2901Q4T?
Neither TLV3701 nor MCP6541 is a direct drop-in replacement for the LM2901Q4T because both are single-channel comparators, while the LM2901Q4T contains four channels. They also use different packages and output characteristics, so a board redesign would be required. These devices may be suitable alternatives when the design can be changed to one channel and its electrical conditions are revalidated.
Where can I buy the LM2901Q4T and request current availability?
Use the Request a Quote form on this page to request current LM2901Q4T availability, minimum order quantity, and delivery information for your required quantity and packaging. The manufacturer offers the part in a 16-QFN-EP package, and multiple authorized distribution channels list the exact MPN. A quote request provides the most appropriate way to confirm current supply without relying on stale catalog availability.
How much does the LM2901Q4T cost and what is its lead time?
Use the Request a Quote form on this page for the current LM2901Q4T unit price, quantity breaks, stock position, and lead time. Pricing and delivery depend on order quantity, package format, market conditions, and current factory allocation. The structured pricing information on this page is refreshed as qualifying distributor listings become available.
Is the LM2901Q4T in stock?
Current stock for the LM2901Q4T should be confirmed through the Request a Quote form on this page using the required quantity and package format. Distributor listings indicate market availability, but inventory can change quickly and may differ by order quantity. Provide your scheduled consumption, shipment destination, and acceptable lead time so the quote can reflect the appropriate supply option.

工程参考数据: LM2901Q4T ——对比、设计指导和合规信息。

选型指南

Choose the LM2901Q4T when the design needs four independent threshold comparisons in a compact 3 mm by 3 mm package. It is particularly useful for industrial voltage supervision, power sequencing, battery monitoring, and sensor conditioning where the monitored signals may require a supply range broader than 5 V. Its 1.1 mA supply current and -40°C to +125°C operating range also suit compact extended-temperature equipment. Select a single-channel comparator such as the TLV3701 or MCP6541 only when one channel is required and a PCB redesign is acceptable. Do not substitute the LM2902Q4T on package similarity alone: although both are quad devices in 16-QFN-related packages, the LM2902 is an operational amplifier and does not establish pin-to-pin comparator compatibility. For any proposed replacement, verify signal assignments, exposed-pad treatment, supply limits, output topology, offset voltage, and propagation delay.

与替代料对比

参数 本产品
Brand STMicroelectronics
Package 16-QFN-EP (3 mm by 3 mm)
Comparator Channels 4 channels
Single-Supply Voltage Range 2 V to 36 V
Dual-Supply Voltage Range ±1 V to ±18 V
Supply Current 1.1 mA
Input Offset Voltage 1 mV
Input Bias Current 25 nA
Propagation Delay 1.3 microseconds
Output Type Open-collector
Operating Temperature Range -40°C to +125°C
Logic Compatibility CMOS, DTL, TTL, MOS, and ECL

关键差异点

  • Four independent monitoring channels in one package (对比 TLV3701)
  • Broader single-supply operating range (对比 MCP6541)
  • Open-collector output architecture (对比 Push-pull comparator)

设计说明

Each open-collector output requires an external pull-up resistor. Select the resistor so the pull-up voltage establishes the required logic-high level while providing adequate sink-current margin for the receiving gate and any wired-collector load. Avoid making the pull-up resistance unnecessarily low, because the output must continuously dissipate current during a low output state. When multiple outputs share a bus, verify that every attached channel can safely enter the high-impedance state during normal operation.

The 16-QFN-EP package includes an exposed thermal pad that should be connected to a copper area on the PCB. Follow the manufacturer land pattern and thermal-via recommendation rather than relying on the nominal package size alone. Although the device has a 1.1 mA supply-current specification, sustained output sinking and elevated ambient temperature still create thermal conditions that should be checked against the manufacturer junction-temperature limit.

Keep the inverting and non-inverting input routes short and place them away from high-current switching traces and inductors. Connect the supply bypass capacitor directly to the appropriate supply pins with a minimal return path, and route the exposed pad to the thermal copper plane without creating accidental connections to sensitive input nets. Differential pairs are not normally required, but matched routing and a quiet reference node can reduce threshold variation.

Do not treat the similar LM2902Q4T as a pin-compatible substitute solely because both use a compact 16-QFN format; the LM2902 family is an operational-amplifier product, not the same comparator function. Also do not assume that an open-collector output reaches a valid logic-high voltage when the comparator is inactive. The output remains high impedance until the external pull-up establishes the high state, and input voltages must remain within the datasheet limits during power transitions.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer product listing identifies the LM2901Q4T as RoHS compliant. No separate qualification claims for REACH, AEC-Q100, halogen-free status, lead-free status, or conflict-minerals reporting were identified.

数据核验日期: 2026-11-15 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

LM2901Q4T datasheet LM2901Q4T datasheet pdf LM2901Q4T pinout LM2901Q4T equivalent LM2901Q4T replacement LM2901Q4T QFN-16 LM2901Q4T price LM2901Q4T stock STMicroelectronics LM2901Q4T LM2901Q4T vs TLV3701 LM2901Q4T vs LM2902Q4T LM2901Q4T open collector application LM2901Q4T 4 channel comparator LM2901Q4T 36V comparator LM2901Q4T supply voltage

相关元器件 & 术语

STMicroelectronics LM2901Q4T LM2902Q4T TLV3701 MCP6541 LM2901 quad voltage comparator comparator IC interface IC mixed-signal IC open-collector output CMOS TTL DTL MOS ECL QFN-16-EP QFN package surface-mount package exposed pad rail-to-rail input input offset voltage input bias current propagation delay power-supply sequencing
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情