STMicroelectronics

LM2903WYPT - Dual Low-Power Comparator, 36V, TSSOP-8 | ST

Référence : LM2903WYPT ✓ Actif
2 V to 36 V Vdss 250 nA Id TSSOP-8 Package
MOQ : 1 |

LM2903WYPT Présentation

The STMicroelectronics LM2903WYPT is a low-power dual voltage comparator featuring two independent comparator channels with open-collector outputs, rated for supply voltages from 2V to 36V (or 1V to 18V split supplies), housed in an 8-pin TSSOP package with an operating temperature range of -40C to +125C.

A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC family, alongside op-amps and difference amplifiers, and form a core part of analog signal conditioning chains in power management, sensing, and control systems. The LM2903 family is one of the most widely used comparator families in the industry, valued for single-supply operation and wide voltage tolerance.

The LM2903WYPT key features include a wide 2V to 36V single-supply operating range, very low input bias current of 250 nA (typical family figure), and open-collector outputs that support wired-OR configurations and level shifting to logic rails up to 36V. The W-grade variant adds enhanced robustness targeted at automotive and industrial environments, and the part is AEC-Q100 qualified, making it suitable for vehicle-level electronics where reliability over temperature is mandatory.

Technically, the device operates from a single supply over a wide voltage range, and operation from split supplies is also possible. The input common-mode range includes ground, allowing the comparator to sense signals near 0V without additional biasing circuitry. The low supply current draw per comparator makes it suitable for battery-powered designs, while the open-collector stage requires an external pull-up resistor to define the output logic level.

Typical applications include automotive sensor interfaces and threshold detection, overvoltage and undervoltage supervision in industrial power supplies, window comparators in battery chargers and motor control feedback, and limit detection in consumer and instrumentation circuits where a low-cost, rugged dual comparator is required.

When designing with this device, remember to fit a pull-up resistor on each open-collector output; without it, the output cannot reach a defined high state. Input and output voltages should never be taken below the negative supply rail, and response time must be budgeted against the low-power biasing.

This page synthesizes distributor listings, drop-in same-family alternatives, AEC-Q100 qualification status, and practical design guidance in one place, going beyond the information found on a typical distributor product card.

Alternatives de remplacement direct pour LM2903WYPT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec LM2903WYPT (même facteur de forme et même empreinte) — différant par Input Bias Current, Output Type, Package.

STMicroelectronics
Input Bias Current: 25 nA typical
Output Type: Open-collector
Package: 8-pin TSSOP
Comparer avec LM2903WYPT →

LM2903YPT

✅ Remplacement direct
STMicroelectronics
📦 TSSOP-8
Low-power dual voltage comparator · 2 channels · 2 independent comparators · +2 V to +36 V · ±1 V to ±18 V · 0.4 mA, independent of supply voltage · 1 mW at +5 V · 25 nA typical

Contactez-nous pour le prix

Voir la fiche technique →
ℹ️ 1 référence(s) à boîtier différent masquée(s) — un boîtier différent exige une retouche du PCB et ne constitue pas un remplacement direct. Contactez-nous si vous souhaitez des suggestions de boîtiers équivalents.

LM2903WYPT Valeurs maximales et caractéristiques électriques

Comparator Channels 2 (dual)
Supply Voltage Range (Single) 2 V to 36 V
Supply Voltage Range (Split) 1 V to 18 V
Input Bias Current 250 nA
Type de sortie Open-Collector, Rail-to-Rail
Input Common-Mode Range Includes ground
Température de fonctionnement -40C to +125C
Boîtier TSSOP-8
Type de montage Surface Mount
Product Series LM2903W
Automotive Qualification AEC-Q100 qualified

Guide de configuration des broches du LM2903WYPT tssop-8

Configuration des broches du LM2903WYPT (boîtier tssop-8). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier tssop-8 pour le LM2903WYPT

Aucune donnée de brochage détaillée disponible pour LM2903WYPT.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

LM2903WYPT convient pour 6 applications: Automotive Sensor Threshold Detection, Overvoltage and Undervoltage Supervision, Battery Charger and BMS Window Comparators, Motor Control Current Limit Detection, Industrial PLC and Limit Detection, Low-Battery Indicators in Portable Devices.

🚗

Automotive Sensor Threshold Detection

In automotive electronics, the LM2903WYPT compares sensor outputs such as pressure switches, coolant-level probes, and position potentiometers against reference thresholds to generate clean digital status signals. Its AEC-Q100 qualification and -40C to +125C rating directly match under-hood and body-electronics environments where temperature cycling is severe. The input common-mode range including ground lets one input be tied to a resistor divider reference near 0V while the other monitors the sensor, all on a single 5V or 12V vehicle rail. Open-collector outputs with pull-ups to the logic rail give fault-safe signaling to the MCU: a broken wire or failed comparator leaves the line low, which the controller interprets as a fault rather than an ambiguous state. The 250 nA input bias current keeps divider networks accurate even with high-impedance sensor sources, minimizing threshold error over the full automotive temperature span.

⚡

Overvoltage and Undervoltage Supervision

Power-supply and industrial-control boards use the LM2903WYPT as a dual-threshold supervisor: one comparator trips on overvoltage and the other on undervoltage, using a resistor divider from the monitored rail against a reference such as a TL431 or Zener. The 2V to 36V supply range means the same part supervises 5V logic rails, 12V and 24V industrial buses, and even 36V telecom inputs without redesign. Its low quiescent current keeps the supervisor's contribution to standby power negligible in always-on equipment. Hysteresis is added easily with positive feedback from the open-collector output through a high-value resistor, giving clean, chatter-free trips near the threshold. Because the outputs are open-collector, the two comparator outputs can be wired-OR into a single active-low RESET or FAULT line pulled up to the controller's logic rail, simplifying interface design in multi-rail systems.

🔋

Battery Charger and BMS Window Comparators

Battery chargers and battery-management front ends deploy the LM2903WYPT as a window comparator: one comparator detects the overcharge voltage ceiling and the other the deep-discharge floor, defining the acceptable cell voltage window. The 2V minimum supply allows monitoring lithium cells directly near their end-of-discharge voltage, and the ground-inclusive common-mode range means the low threshold can sit right at 0V reference. The 250 nA bias current permits large-value (100k to 1M) divider resistors, so the monitoring network itself draws microamps - critical in portable and backup-battery products where the supervision circuit must run for years. Charge-complete detection is similarly implemented by comparing the battery voltage against a reference with a small hysteresis band, and the open-collector output pulls low to signal the charge controller, giving a defined state even during brownout conditions.

⚙️

Motor Control Current Limit Detection

In motor drives, the LM2903WYPT monitors the voltage across a low-side current-sense shunt and trips when the motor current exceeds the programmed limit, feeding a fault line to the driver or MCU. Its common-mode range extending to ground is essential here, because the shunt sits at ground potential in low-side sensing, and many comparators cannot sense signals at their own negative rail. The 36V rating provides ample headroom for 12V and 24V drive systems, including automotive actuators covered by the part's AEC-Q100 qualification. Response to overcurrent should account for the low-power family's propagation delay, so fast-switching designs add a small amount of filtering or pair the comparator with driver-level protection. The open-collector output pulls low on fault, allowing wired-OR combination of multiple limit detectors - per-phase current, bus overvoltage, and thermal flags - into one interrupt line.

🏭

Industrial PLC and Limit Detection

Programmable logic controllers and industrial instrumentation use dual comparators like the LM2903WYPT for limit switches, level detection, and analog-to-logic interfacing on 24V control systems. The part's 2V to 36V supply range covers the industrial 24V rail directly, eliminating an extra regulator just for the comparison stage, while its -40C to +125C rating suits unconditioned cabinets and outdoor panels. Inputs tolerate signals referenced to ground or a mid-rail reference, so the same design compares 4-20mA-derived voltages, thermistor bridges, or potentiometer position feedback. Outputs pulled up to a 5V logic rail safely interface with the controller's digital inputs despite the 24V analog domain, thanks to the open-collector architecture. Designers commonly add RC filtering at the inputs and slight hysteresis to reject contact bounce and industrial noise, producing robust, debounce-free limit signals for the PLC scan cycle.

📱

Low-Battery Indicators in Portable Devices

Portable and battery-backed products use one comparator of the LM2903WYPT to generate a low-battery flag: the cell voltage is divided and compared against a stable reference, and when it falls below the threshold the open-collector output pulls low to light an LED or wake the microcontroller. Total quiescent draw is dominated by the divider network rather than the comparator, so with high-value resistors the indicator adds only microamps of continuous load - decisive for devices expected to hold charge for months. The 2V minimum supply keeps the comparator alive down near lithium end-of-discharge, ensuring the warning itself still works at the very moment it matters. The second comparator is often used as a charge-present detector or to gate the indicator during charging. The TSSOP-8 footprint fits dense portable layouts, and the low cost makes dual-function supervision essentially free in the bill of materials.

What is the operating voltage range of LM2903WYPT?
The LM2903WYPT operates from a single supply of 2V to 36V, or from split supplies of 1V to 18V per rail. According to the STMicroelectronics LM2903W datasheet, the device consists of two independent low-power voltage comparators designed specifically to operate from a single supply over a wide range of voltages, and operation from split power supplies is also possible. This wide range lets one part serve 5V, 12V, 24V, and 36V industrial rails without redesign.
What package does LM2903WYPT come in?
The LM2903WYPT is supplied in an 8-pin TSSOP package (surface mount). DigiKey lists it as a general-purpose dual comparator with open-collector, rail-to-rail output in an 8-TSSOP body. The TSSOP-8 footprint is a common industry outline, which means second-source layouts based on other LM2903-family SOIC-8 or TSSOP-8 parts can often be reused, though the SOIC-8 and TSSOP-8 outlines differ and the PCB land pattern must match the chosen package exactly.
Is LM2903WYPT AEC-Q100 qualified for automotive applications?
Yes, the LM2903WYPT is AEC-Q100 qualified and rated for the -40C to +125C temperature grade required by automotive electronics. The W suffix in the ST part number denotes the enhanced automotive-grade variant of the LM2903 family. ST's own product page for the LM2903W series describes it as suitable for single-supply operation over a wide voltage range, and the qualification makes it acceptable for vehicle sensor interfaces, body electronics, and power supervision modules subject to automotive quality flows.
What is the difference between LM2903WYPT and LM2903YPT?
Both are STMicroelectronics dual comparators in the same TSSOP-8 package with the same 2V to 36V rating, but the LM2903WYPT is the W-grade automotive variant with AEC-Q100 qualification, while the LM2903YPT is the standard industrial/commercial grade. For consumer or industrial boards the standard LM2903YPT is usually sufficient and lower cost; for automotive or high-reliability designs the WYPT should be chosen. Verify the exact parametric deltas in the two datasheet revisions before substituting in a production layout.
Can LM2903WYPT replace LM2903QPWRG4Q1?
Yes, the LM2903WYPT can generally replace the TI LM2903QPWRG4Q1 in automotive applications, since both are AEC-Q100 qualified dual comparators with open-collector outputs and similar electrical characteristics in 8-pin TSSOP packages. However, always verify pinout and footprint alignment in your PCB layout before committing the swap - pin assignment of the two comparators and supply pins must match the land pattern. A prototype build and bench validation of switching thresholds and response time is strongly recommended for safety-relevant automotive circuits.
Does LM2903WYPT need pull-up resistors on its outputs?
Yes, the LM2903WYPT has open-collector outputs, so each output requires an external pull-up resistor to the desired logic rail to produce a defined high level. Without a pull-up, the output can only pull low and floats when the comparator releases. The pull-up can connect to a voltage different from the comparator supply, enabling level shifting to 3.3V or 5V logic. Typical pull-up values of 1k to 100k trade speed against current consumption; lower values give faster rising edges but draw more current when the output is low.
Where can I download the LM2903WYPT datasheet PDF?
The official LM2903WYPT datasheet PDF is available from STMicroelectronics at st.com, on the LM2903W product page under the Documentation section. The same document covers the full LM2903W family, including pinout diagrams, absolute maximum ratings, electrical characteristics over temperature, and typical application circuits. Third-party datasheet mirrors exist, but the ST website always carries the latest revision, so use it as the authoritative source when checking parameters for production designs.
What is the input bias current of LM2903WYPT?
The LM2903WYPT family is characterized with an input bias current of approximately 250 nA, as reflected in distributor parametric listings for the LM2903 series dual 36V comparator. This low bias current means very high input impedance, so large-value divider resistors (100k and above) can be used in threshold networks without significant error. For precision threshold designs, always check the datasheet's bias-current-versus-temperature curves, because bias current rises with temperature and can shift detection thresholds in hot environments such as engine bays.
Is LM2903WYPT suitable for battery-powered designs?
Yes, the LM2903WYPT belongs to the low-power LM2903 family, consuming very little quiescent current per comparator, which makes it suitable for battery-powered supervision circuits such as low-battery indicators and over-discharge cut-off detection. Combined with its 2V minimum supply, it can monitor cells down near end-of-charge voltage. Add generous value resistors in the divider network and use the open-collector output with a high-value pull-up to minimize total current draw; with 100k network resistors the comparator's 250 nA bias current contributes only tens of microvolts of error.
What are the key specifications of LM2903WYPT that engineers should know?
The LM2903WYPT is a dual low-power voltage comparator in TSSOP-8 from STMicroelectronics. Key specifications: supply range 2V to 36V single (1V to 18V split), input bias current around 250 nA, open-collector rail-to-rail outputs with wired-OR capability, input common-mode range including ground, operating temperature -40C to +125C, and AEC-Q100 automotive qualification. The two independent comparators share supply pins, and each output needs a pull-up resistor. These figures come from the ST LM2903W datasheet and distributor parametric data.
What is the best drop-in replacement for LM2903WYPT?
The closest drop-in replacement is the STMicroelectronics LM2903YPT, which shares the same TSSOP-8 package, pinout, 2V to 36V range, and open-collector outputs; the only material difference is that it is the non-W industrial grade rather than the AEC-Q100 automotive grade, so it suits consumer and industrial boards but not automotive flows. Within the LM2903 ecosystem, TI's LM2903B family is also a pin-for-pin equivalent in function, but its SOIC-8 package differs from TSSOP-8, so a PCB footprint change would be needed - not a true drop-in.
What is the difference between LM2903 and LM2903W?
The LM2903W is STMicroelectronics' enhanced automotive-grade version of the standard LM2903 dual comparator. Both offer two independent low-power comparators with open-collector outputs designed to operate from a single supply over a wide voltage range, per the ST LM2903W datasheet. The W version carries AEC-Q100 automotive qualification and the corresponding -40C to +125C temperature rating, plus process enhancements for high-humidity reliability and parametric stability over temperature. Standard LM2903 parts remain fine for industrial and consumer use where automotive qualification is not required.
Where to buy LM2903WYPT online?
You can request LM2903WYPT through the Request a Quote form on this XAIPART product page, which is answered with current stock, pricing, and lead time. The part is an active STMicroelectronics catalog item carried by major authorized distributors, so availability is generally good. When sourcing, insist on original ST parts with traceability - counterfeit LM2903-family parts are common in the open market. For volume production, request tape-and-reel packing quantities and confirm date codes for long-life programs.
What is the lead time and packaging of LM2903WYPT?
The LM2903WYPT is an active, generally well-stocked catalog part, so lead times are typically short, but exact figures change with market conditions - request the current lead time through the Request a Quote form on this page. Standard factory packaging is tape and reel for automated SMT assembly; cut tape and tube options are commonly available through distributors for prototype builds. Because the part is AEC-Q100 qualified, automotive customers may specify delivery with ST certificate of conformance documentation, so state your documentation needs when requesting a quote.
Can LM2903WYPT operate from a 5V single supply with ground-referenced inputs?
Yes, the LM2903WYPT operates from 2V to 36V single supply, so a 5V rail is fully within range, and its input common-mode voltage range includes ground. This means one input can be tied directly to 0V (for example as a reference) while the other senses a signal near ground, without requiring a negative rail or bias network. The open-collector output with a pull-up to 3.3V or 5V delivers a clean logic-level trip signal to a microcontroller. This ground-sensing capability is a signature strength of the LM2903 family for low-side current and threshold detection.
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ