LM2904N/NOPB Dual 1 MHz Op Amp 26 V | Texas Instruments
Référence : LM2904N/NOPB ✓ ActifLM2904N/NOPB Présentation
An operational amplifier is an amplifier IC that uses high open-loop gain to increase the voltage difference between its differential inputs. In the feedback-defined signal chain, the LM2904N/NOPB belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and semiconductor. Its two independent channels allow two separate signal paths in one package, reducing board area compared with two single-amplifier packages.
Key features include two amplifier circuits, a 26 V supply-voltage rating, 1 MHz gain-bandwidth, internal frequency compensation, and operation from a single supply or split supplies. The internal compensation removes the need for an external compensation network in ordinary closed-loop configurations. The dual-channel architecture is useful for two-stage filters, differential signal handling, buffer stages, and paired feedback networks. The 8-pin PDIP format supports through-hole assembly and prototyping systems.
The LM2904-N family is intended for general-purpose applications where a single-supply-friendly amplifier with a wide supply range is more important than rail-to-rail output swing or very high bandwidth. The device can be used as an inverting amplifier, non-inverting amplifier, voltage follower, comparator in suitable applications, or the active element in a filter. Its internally compensated architecture simplifies design, although users should account for input common-mode limitations, output swing, stability margin, and slew-rate limits when selecting feedback values.
Typical applications include low-frequency sensor interfaces, transducer signal conditioning, process-control loops, audio preamplifier stages, data-acquisition systems, and general power-control circuitry. Two amplifiers in one package are especially useful in dual-channel analog boards, instrumentation amplifiers using several gain stages, and active filter designs. The 1 MHz bandwidth supports many low- and mid-frequency industrial signals rather than high-speed video or RF tasks.
For PCB design, use the manufacturer's pin-description table and package drawing when assigning connections. Keep input and feedback traces short, provide adequate supply bypassing, and avoid placing high-impedance input nodes next to switching nodes. If the source impedance is high, add a bias resistor or buffer stage to reduce input bias-current effects and offset error. Check the operating region against the device's supply and common-mode limits.
This product page combines the LM2904N/NOPB ordering information with package, pinout, application, and drop-in replacement guidance. The comparison table highlights verified package and functional differences, while the design notes focus on practical PCB and signal-chain decisions for engineers evaluating the LM2904N/NOPB.
Alternatives de remplacement direct pour LM2904N/NOPB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2904N/NOPB (même facteur de forme et même empreinte) — différant par Package, Mounting Type, AEC-Q100 Qualification, RoHS Status.
LM2904BIDR
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LM2904N
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904N
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904N
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904N/NOPB Valeurs maximales et caractéristiques électriques
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1 MHz |
| Supply Type | Single supply or split supply |
| Frequency Compensation | Internal |
| Boîtier | 8-PDIP |
| Type de montage | Through-hole |
| AEC-Q100 Qualification | Not applicable |
Configuration des broches de LM2904N/NOPB
| Broche 1 | OUT A — Amplifier A output |
| Broche 2 | IN A- — Inverting input for amplifier A |
| Broche 3 | IN A+ — Non-inverting input for amplifier A |
| Broche 4 | V- — Negative supply connection |
| Broche 5 | IN B+ — Non-inverting input for amplifier B |
| Broche 6 | IN B- — Inverting input for amplifier B |
| Broche 7 | OUT B — Amplifier B output |
| Broche 8 | V+ — Positive supply connection |
Applications typiques
LM2904N/NOPB convient pour 6 applications: Industrial Sensor Signal Conditioning, Process Control Loops, Audio Preamplifier Stages, Data Acquisition and Instrumentation, Active Filter and Waveform Conditioning, Power Supply Feedback and Monitoring.
Industrial Sensor Signal Conditioning
The LM2904N/NOPB is useful for conditioning low-frequency industrial sensor signals because it provides two independent, internally compensated amplifiers in one 8-PDIP package. One channel can buffer the sensor while the second can perform gain or filtering, reducing board area and simplifying through-hole assembly. With a 26 V maximum supply rating and approximately 1 MHz gain-bandwidth product, it suits process signals that change slowly relative to the amplifier bandwidth. The design should still verify the sensor output range against the input common-mode limits and account for offset and bias-current error at high source impedance.
Recommandé
Process Control Loops
The LM2904N/NOPB can implement error amplifiers, comparators, and output-buffer stages in a process-control board. Its dual-channel arrangement is valuable when one amplifier processes a feedback signal and the other drives a control or monitoring path. The 26 V supply rating accommodates many industrial interface voltages, while internal frequency compensation reduces external-component requirements for ordinary closed-loop designs. Confirm the output swing at the selected load and check the common-mode range around the setpoint, because the device is not a rail-to-rail precision amplifier.
Recommandé
Audio Preamplifier Stages
The LM2904N/NOPB can serve as a low-frequency audio preamplifier or active filter stage when the operating frequency is well below its approximately 1 MHz gain-bandwidth product. Two amplifiers in one 8-PDIP package allow a compact implementation of gain and filtering functions in a through-hole design. The device is appropriate for conventional audio-control and instrumentation paths, but designers should verify output swing, slew rate, noise performance, and load capability against the source and speaker or measurement interface.
Recommandé
Data Acquisition and Instrumentation
The LM2904N/NOPB fits low-frequency data-acquisition front ends where a dual amplifier can buffer an input and implement gain, summation, or active filtering. The broad supply capability supports single-rail or split-rail analog sections, and the internally compensated architecture simplifies stable closed-loop implementation. For instrumentation designs, preserve signal integrity by keeping high-impedance input routes short, using adequate bypass capacitance, and avoiding shared copper paths with switching or digital return currents.
Recommandé
Active Filter and Waveform Conditioning
The LM2904N/NOPB is useful for two-stage active filters, waveform conditioners, and gain blocks operating at low or moderate frequencies. Its approximately 1 MHz gain-bandwidth product provides useful design margin for many audio, control, and instrumentation bandwidths, while the dual package reduces component count. Select feedback resistors and capacitors against the closed-loop bandwidth and stability requirements, and ensure that the signal remains inside the amplifier's input and output common-mode limits.
Recommandé
Power Supply Feedback and Monitoring
The LM2904N/NOPB can monitor a supply rail, amplify a feedback error, or drive a low-current control signal in a power-control system. The 26 V maximum supply rating is relevant for industrial rails, while split-supply operation permits comparison and signal-conditioning circuits around ground. Because it is a general-purpose amplifier rather than a dedicated supervisor or precision reference, verify offset behavior, output drive, and input common-mode limits against the monitoring thresholds before deployment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2904N/NOPB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2904B | LM2904N | LM2904N | LM2904N |
|---|---|---|---|---|---|
| Package | 8-PDIP | 8-PDIP | 8-Mini DIP | 8-PDIP | 8-PDIP |
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi | NXP Semiconductors |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual |
| General-Purpose Application | Standard dual operational amplifier | Standard dual operational amplifier | Standard dual operational amplifier | General-purpose dual operational amplifier | General-purpose dual operational amplifier |
Principaux différenciateurs
- Two independent general-purpose amplifiers in one through-hole package (vs Single-amplifier alternatives)
- Single-supply and split-supply operating flexibility (vs Rail-to-rail precision amplifiers)
- Through-hole integration in the 8-PDIP format (vs STMicroelectronics LM2904N)
Notes de conception
Place the power-supply bypass capacitor immediately between pins 8 and 4, with the capacitor and IC close to the device. Keep the high-current return path away from sensitive input and feedback traces. For single-supply operation, connect the bypass return directly to the appropriate ground reference and avoid routing analog input return through digital or switching-current paths.
Keep the inverting-input node physically short because feedback resistance and stray capacitance can alter gain and stability. Use a small isolation resistor close to the amplifier input when driving high-capacitance loads or sampling nodes. Avoid long unshielded traces from high-impedance sensors, and maintain a clean analog ground reference to reduce offset coupling.
Do not assume that every LM2904-family marking is interchangeable. Verify the exact manufacturer, package dimensions, pin numbering, supply rating, common-mode range, output swing, input offset, and bias current. The LM2904N/NOPB is a Texas Instruments 8-PDIP device; a similarly named part from another manufacturer may use a related but different DIP package and may have different electrical limits.
Informations de conformité
The LM2904-N product family is identified as a general-purpose dual operational amplifier. Automotive qualification and specific environmental compliance declarations are not established by the listed information.