LM358AWPT - Low-Power Dual Op Amp | STMicroelectronics | TSSOP-8
Référence : LM358AWPT ✓ ActifLM358AWPT Présentation
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual operational amplifier contains two amplifier sections that share common supply and ground connections but can process separate signals. In the broader semiconductor hierarchy, the LM358 belongs to the operational-amplifier class, then to amplifier ICs, analog ICs, and ultimately the wider integrated-circuit and semiconductor categories.
The LM358AWPT is identified by STMicroelectronics as a low-power dual operational amplifier. Its two-circuit configuration reduces component count and board area when two related analog functions must be implemented. The 8-pin TSSOP package supports automated assembly while preserving a compact outline. The listed 40 mA output-current capability also makes the device relevant to designs that require more drive than a minimum-footprint micropower amplifier.
Each amplifier section can support common analog signal-processing tasks such as voltage amplification, impedance buffering, comparators, current-sensing interfaces, and active-feedback control. Because the two channels share package-level power pins, their operating supply is common even when they perform unrelated functions. PCB designers should still route input, output, supply, and ground connections carefully to minimize coupling between the two channels and to preserve signal integrity near the device.
Typical applications include industrial sensor interfaces, low-voltage control loops, audio and communications equipment, battery-powered instrumentation, and general-purpose analog signal conditioning. In a feedback controller, one channel might amplify a sensor signal while the other buffers a reference or drives an error amplifier. In a sensing circuit, the dual organization can reduce the number of packages needed compared with separate single-channel amplifiers.
The principal design consideration is supply compatibility. Confirm the minimum and maximum operating voltages, input common-mode range, output swing, input bias current, noise, slew rate, and stability requirements in the STMicroelectronics manufacturer datasheet before using the device with a selected system rail. Decoupling capacitors, grounding, output-load limits, and any reactive load compensation should follow the application guidance in that datasheet.
This product page organizes the LM358AWPT information around verified product identity, package details, directly compatible replacement options, application guidance, and PCB-level design considerations. It also distinguishes exact drop-in candidates from broader LM358 comparisons so that engineers can assess footprint, function, and operating-limit compatibility before authorizing a substitution.
Alternatives de remplacement direct pour LM358AWPT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM358AWPT (même facteur de forme et même empreinte) — différant par Amplifier Type, Package.
LM358AWYPT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM358APT
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LM358PT
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LM358AQUPT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM358AYPT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LM358AWPT Valeurs maximales et caractéristiques électriques
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Output Current Capability | 40 mA |
| Power Class | Low power |
| Package Type | 8-pin TSSOP |
| Total Pin Count | 8 pins |
| Type de montage | Surface mount |
Configuration des broches de LM358AWPT
| Broche 1 | OUT1 — Output of amplifier channel 1 |
| Broche 2 | IN1− — Inverting input of amplifier channel 1 |
| Broche 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Broche 4 | V− — Negative supply connection |
| Broche 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Broche 6 | IN2− — Inverting input of amplifier channel 2 |
| Broche 7 | OUT2 — Output of amplifier channel 2 |
| Broche 8 | V+ — Positive supply connection |
Applications typiques
LM358AWPT convient pour 6 applications: Industrial Sensor Signal Conditioning, Battery-Powered Instrumentation, Audio Preamp and Output Buffering, Communications Interface Buffering, Active Feedback Control, Test and Measurement Front Ends.
Industrial Sensor Signal Conditioning
The LM358AWPT fits sensor-amplification and conditioning stages that require two channels in one compact 8-pin TSSOP package. One section can amplify a sensor output while the other provides buffering or reference amplification, reducing the number of separate amplifier packages and associated board area. Its listed 40 mA output-current capability also provides useful drive margin for moderate loads. Before finalizing the design, confirm that the selected sensor output lies within the input common-mode range and that the required gain and accuracy satisfy the electrical limits in the STMicroelectronics manufacturer datasheet. Place bypass capacitance close to pins 8 and 4 and keep high-impedance input traces short to reduce susceptibility to noise and parasitic loading.
Recommandé
Battery-Powered Instrumentation
The LM358AWPT is appropriate for low-voltage instrumentation in which two low-power amplifier sections are useful on a common supply rail. A channel can condition a transducer signal while the second channel buffers an intermediate node, creates an adjustable reference, or forms part of an error-feedback loop. The 8-pin TSSOP footprint is particularly useful where a through-hole dual-op-amp package would consume excessive board area. Because low-power operation does not automatically mean unrestricted input or output ranges, verify supply current, input common-mode limits, output swing, and quiescent behavior against the expected battery operating region. Stable power-ground routing and local supply bypass are essential when both channels operate near low signal amplitudes.
Recommandé
Audio Preamp and Output Buffering
The two channels in the LM358AWPT can support separate stages in a low-frequency audio preamplifier, such as input amplification followed by gain or impedance buffering. The device must be assessed for the audio band of interest, output swing on the chosen supply, capacitive-load behavior, and noise performance using the STMicroelectronics manufacturer datasheet. Its listed 40 mA output-current capability is useful when driving the next stage through a coupling network, but it does not remove the need to observe maximum output-current and voltage limits. Keep the two amplifier paths physically separated enough to limit feedback through shared supply impedance, and place the supply bypass capacitor where it can suppress coupling from both channels effectively.
Recommandé
Communications Interface Buffering
The LM358AWPT can be used in communications equipment for impedance conversion, gain adjustment, and active feedback around line-driver or receiver stages. Its dual-channel organization permits one amplifier to condition the forward signal path while the other supports feedback, monitoring, or a second polarity. The 8-pin TSSOP package supports compact surface-mount assemblies, while the two channels share common supply pins that require careful decoupling. Confirm that the signal amplitude remains inside the input common-mode range and that the output can meet the load's voltage and current requirements. Route sensitive input traces away from output and high-current return paths, and use a continuous ground reference to minimize channel-to-channel coupling and data errors.
Recommandé
Active Feedback Control
The LM358AWPT can implement error amplification in an active feedback control loop when its bandwidth, slew rate, input common-mode range, and output swing are adequate for the loop. One channel can compare a feedback signal with a reference, while the other can buffer the reference or drive an additional analog stage. The device's two amplifier channels and compact 8-pin TSSOP package make it a practical fit for dual-loop industrial and control boards. Stability analysis must account for the sensor path, compensation method, load, and supply impedance. In particular, confirm operating limits from the STMicroelectronics manufacturer datasheet and place the bypass capacitor close to the package to prevent supply feedback from degrading loop stability.
Recommandé
Test and Measurement Front Ends
The LM358AWPT is suitable for compact test and measurement front ends that need signal amplification and buffering within the same 8-pin TSSOP package. One channel can amplify a probe or sensor output, while the other can buffer it for an ADC, comparator, or instrument input stage. The general-purpose architecture also supports offset-null and feedback-network layouts when precision requirements permit. Validate the full measurement chain against the manufacturer's offset-voltage, bias-current, noise, bandwidth, and common-mode specifications rather than relying on nominal gain alone. Use short guarded input traces, a low-impedance ground return, and local supply bypassing to preserve measurement integrity and minimize channel coupling.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM358AWPT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM358AWYPT | LM358APT | LM358PT | LM358AQUPT | LM358AYPT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Power Class | Low power | Low power | Low power | Low power | Low power | Low power |
Principaux différenciateurs
- Combines two amplifier channels in one compact surface-mount package (vs LM324ANSR)
- Maintains the same TSSOP footprint across STMicroelectronics LM358A ordering variants (vs LM358AWYPT)
- Uses the standard dual-op-amp pin arrangement for straightforward PCB implementation (vs LM358PT)
Notes de conception
Place the supply bypass capacitor immediately between pins 8 and 4, with a short ground return and minimal loop area. Route the two amplifier channels to avoid sharing long input or output paths, because the channels use common supply pins even though their signal inputs and outputs are independent. Use the manufacturer application guidance for the recommended capacitance and ESR range.
Do not select a generic LM358 replacement from the device name alone. Confirm that the substitute has an 8-pin TSSOP land pattern, the same pin assignments, adequate supply-voltage range, acceptable input common-mode range, and the required output-current capability. Generic cross-reference pages may include DIP and SOIC devices, which do not match this TSSOP footprint.
Keep high-impedance inputs short and guard them against nearby outputs, clock lines, inductors, and switching nodes. If either channel drives a capacitive load, verify stability in the STMicroelectronics manufacturer datasheet and add isolation resistance close to the output when required. Separate sensitive ground returns from output-current paths to reduce channel-to-channel coupling.
Check the complete supply operating region rather than only nominal rail voltage. Confirm minimum input voltage for correct operation, maximum supply voltage, output swing, quiescent current, and output-current limits. If both channels can operate near the output-current capability of 40 mA, calculate the worst-case power dissipation and provide copper area and layout conditions consistent with the package thermal data.
Informations de conformité
Compliance status is not stated in the product records used for this page. Check the current STMicroelectronics product documentation and declaration before using the LM358AWPT in a regulated production design.