LT1007CJ8 - Low-Noise Precision Op Amp | Analog Devices
Référence : LT1007CJ8 ✓ ActifLT1007CJ8 Présentation
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input voltage noise, low offset drift, high rejection ratios, and predictable gain behavior are more important than maximum output-current capability. This makes the family suitable for conditioning low-level signals from strain gauges, precision sensors, audio circuits, laboratory instrumentation, and high-resolution measurement systems.
The LT1007 combines a 2.5 nV/√Hz noise density with a 2 Hz 1/f corner frequency and approximately 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. Its 10 µV offset voltage and 0.2 µV/°C drift support accurate DC measurements, while 130 dB common-mode rejection and 130 dB power-supply rejection reduce errors caused by common-mode voltages and imperfect supply rails. These characteristics are particularly valuable when the input signal is smaller than the unwanted offsets, noise, or supply ripple present in the measurement chain.
The series uses precision internal design techniques to achieve low noise and stable operation. The standard LT1007 is stable for closed-loop gains of 5 or higher, while the decompensated LT1037 provides higher gain-bandwidth-product performance and is also stable at gain 5 or above. Designers must account for this minimum stable gain when selecting feedback values. Decoupling close to the supply pins, maintaining clean ground returns, and avoiding long input traces are therefore central to preserving the intended noise performance.
Typical uses include low-level bridge and thermocouple amplification, precision current-to-voltage conversion, audio and instrumentation preamplifiers, low-level sensor interfaces, and laboratory measurement equipment. In these applications, the LT1007 can amplify weak signals close to its noise floor while rejecting common-mode interference and supply-related disturbance. The 8-pin CERDIP package also supports applications that benefit from a through-hole mechanical format rather than a surface-mount land pattern.
A key design consideration is that minimum gain stability differs from conventional unity-gain-stable amplifiers. Feedback configurations must provide a gain of at least 5, and input/output capacitance should be checked against the frequency-response and stability requirements in the manufacturer datasheet. Low-noise performance also depends on resistor selection, source impedance, grounding, supply bypassing, and shielding rather than the amplifier alone.
This product overview consolidates the LT1007CJ8 electrical characteristics, package information, drop-in-family alternatives, and practical application guidance. It supports faster engineering comparisons while directing detailed pin assignments, test conditions, and absolute-maximum ratings to the official Analog Devices LT1007 datasheet and product documentation.
Alternatives de remplacement direct pour LT1007CJ8 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LT1007CJ8 (même facteur de forme et même empreinte) — différant par Package, Amplifier Type.
LT1037CJ8
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LT1007ACJ8
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LT1012CJ8
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LT1013CJ8
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LT1006CJ8
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LT1007CJ8 Valeurs maximales et caractéristiques électriques
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Wideband Input Noise Density | 2.5 nV/√Hz |
| Guaranteed 10 Hz Noise Density | 4.5 nV/√Hz |
| Guaranteed 1 kHz Noise Density | 3.8 nV/√Hz |
| 0.1 Hz to 10 Hz Noise | 60 nV peak-to-peak typical |
| 1/f Corner Frequency | 2 Hz |
| Input Offset Voltage | 10 µV |
| Input Offset Drift | 0.2 µV/°C |
| Common-Mode Rejection Ratio | 130 dB |
| Power-Supply Rejection Ratio | 130 dB |
| LT1037 Gain-Bandwidth Product | 60 MHz |
| Minimum Stable Closed-Loop Gain | 5 |
| Minimum Voltage Gain | 2 million typical |
| Boîtier | 8-pin CERDIP |
| Type de montage | Through-hole |
Guide de configuration des broches du LT1007CJ8 8-pin cerdip
Configuration des broches du LT1007CJ8 (boîtier 8-pin cerdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LT1007CJ8.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LT1007CJ8 convient pour 6 applications: Precision Bridge Amplifier, Thermocouple Signal Conditioning, Audio Instrumentation Preamp, Laboratory Voltage Measurement, Precision Current-to-Voltage Conversion, Low-Level Sensor Interface.
Precision Bridge Amplifier
The LT1007CJ8 fits low-level bridge measurement because its 2.5 nV/√Hz wideband noise and 10 µV offset voltage establish a low noise floor relative to many strain-gauge and resistive-sensor outputs. The 130 dB common-mode rejection helps suppress the relatively large common-mode voltage often present on bridge excitation while the small differential signal is amplified. Place the amplifier where the gain is at least 5 and route input and reference connections away from switching nodes. Resistor matching, excitation symmetry, grounding, and input filtering remain important because amplifier noise alone does not determine the complete measurement accuracy.
Recommandé
Thermocouple Signal Conditioning
The LT1007CJ8 is useful for thermocouple and other millivolt-level signal paths because its 10 µV offset voltage and 0.2 µV/°C drift limit static error as temperature changes. The 2.5 nV/√Hz noise density supports low-level amplification where the thermocouple emf can be smaller than the contribution of a higher-noise amplifier. Use a minimum stable gain of 5 and account for thermoelectric junctions at the connector and PCB boundary. Cold-junction compensation, input protection, guarded grounding, and careful high-impedance layout are necessary to preserve the benefit of the amplifier's low offset and noise.
Recommandé
Audio Instrumentation Preamp
The LT1007CJ8 can serve in a low-noise audio preamplifier when signal integrity and minimum gain are compatible with the application. Its 2.5 nV/√Hz wideband noise density, 60 nV peak-to-peak 0.1 Hz to 10 Hz noise, and 2 Hz 1/f corner make it useful for high-gain microphone and laboratory audio paths. The LT1007 is stable for gains of 5 or higher, so conventional unity-gain microphone layouts may require a different family member. Keep input leads short, use low-value noise-appropriate feedback resistors, and isolate the amplifier from vibration, mains fields, and switching supply noise.
Recommandé
Laboratory Voltage Measurement
The LT1007CJ8 is appropriate for laboratory front ends that measure small voltages with demanding accuracy. Its 10 µV offset, 0.2 µV/°C drift, and 130 dB common-mode rejection reduce errors from input offset, temperature change, and common-mode voltage. The 130 dB power-supply rejection also helps when the available supply contains ripple. Configure the closed-loop gain at 5 or above and use a shielded, guarded layout to reduce leakage and thermoelectric effects. The amplifier should be calibrated with the complete front end so resistor tolerances, source impedance, reference quality, and acquisition-system offsets are represented in the final uncertainty.
Recommandé
Precision Current-to-Voltage Conversion
The LT1007CJ8 is useful for current-to-voltage conversion when the sensed current produces a signal near the amplifier's input-noise and offset limits. A transimpedance configuration can benefit from 2.5 nV/√Hz wideband noise and 10 µV input offset, while the high common-mode rejection reduces disturbance from supply and ground variations. Choose feedback resistance and gain carefully because very high transimpedance values interact with input and parasitic capacitance and can reduce stability. Confirm that the selected gain remains at least 5, and evaluate the complete input network, guarding, compensation, and settling behavior rather than relying on amplifier specifications alone.
Recommandé
Low-Level Sensor Interface
The LT1007CJ8 supports precision sensor interfaces for resistive, magnetic, optical, and other analog sensors whose output changes are small relative to common-mode voltage or supply variation. Its 130 dB common-mode rejection and 130 dB power-supply rejection help protect weak signals, while the low offset and drift reduce errors over time and temperature. The device's minimum stable gain of 5 must be included early in the signal-chain design. Use short guarded inputs, low-noise feedback components, clean references, and local supply bypassing; these implementation details often determine whether the amplifier achieves its datasheet-level performance in a complete instrument.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LT1007CJ8 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LT1037CJ8 | LT1007ACJ8 | LT1012CJ8 | LT1013CJ8 | LT1006CJ8 |
|---|---|---|---|---|---|---|
| Package | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Circuit Configuration | Single amplifier | Single amplifier | Single amplifier | Single amplifier | Dual amplifier | Single amplifier |
Principaux différenciateurs
- Very low wideband input noise (vs LT1013CJ8)
- Strong DC rejection and stability (vs LT1012CJ8)
- Higher-speed option in the same ceramic-DIP family (vs LT1007CJ8)
Notes de conception
Do not treat the LT1007 as a unity-gain-stable amplifier. The manufacturer specifies stability for closed-loop gains of 5 or greater, so verify the feedback ratio before committing the PCB. The LT1037 variant is also decompensated and remains stable at gain 5 or above. For inverting or differential circuits, calculate the noise gain rather than relying only on the signal gain, and confirm bandwidth and stability using the applicable manufacturer curves.
Preserve low-noise performance by placing input and compensation networks close to the appropriate device pins and by keeping sensitive input traces short. Avoid routing inputs alongside switching-regulator traces, relay contacts, high-current motor lines, or clock and data edges. Use a continuous ground reference beneath sensitive analog sections, provide local supply bypassing, and avoid creating ground-current paths through input return conductors.
The low 2.5 nV/√Hz noise density is valuable only if the rest of the signal chain does not add more noise. Select feedback resistors with suitable thermal noise and temperature coefficients, minimize source impedance where practical, and apply gain of at least 5. For very high source impedances, account for bias-current errors and resistor-generated noise. For long or high-impedance nodes, use guarding and consider the 60 nV peak-to-peak 0.1 Hz to 10 Hz family noise when evaluating drift performance.
Estimated: the LT1007CJ8 dissipation can be calculated as P = (VIN - VOUT) × IOUT plus the supply current contribution. If VIN is 15 V, VOUT is 5 V, and IOUT is 10 mA, the estimated pass-element dissipation is 0.10 W before bias current. Check this against the device's package thermal limits, ambient temperature, and socket or PCB thermal resistance. The amplifier's low-noise performance does not remove the need for temperature-rise and stability analysis.
Informations de conformité
The exact compliance declarations for LT1007CJ8 require confirmation from the current Analog Devices product documentation or a supplier compliance statement. AEC-Q100 qualification is not applicable to this general-purpose instrumentation amplifier.