Analog Devices

LT1007CJ8 - Low-Noise Precision Op Amp | Analog Devices

料号: LT1007CJ8 ✓ 量产中
10 µV Vdss 8-pin CERDIP Package 2 Hz Speed
最小起订量: 1 |

LT1007CJ8 概述

The Analog Devices LT1007CJ8 is a low-noise, high-speed precision operational amplifier with 2.5 nV/√Hz wideband noise, 10 µV offset voltage, 0.2 µV/°C drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. The device is packaged in an 8-pin CERDIP package and is intended for instrumentation, sensor-signal conditioning, and precision analog systems that require low input-referred noise and accurate DC behavior. The LT1007 family combines monolithic low-noise characteristics with a 60 MHz gain-bandwidth product on the decompensated LT1037 variant.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. The LT1007 belongs to the precision operational-amplifier hierarchy, where low input voltage noise, low offset drift, high rejection ratios, and predictable gain behavior are more important than maximum output-current capability. This makes the family suitable for conditioning low-level signals from strain gauges, precision sensors, audio circuits, laboratory instrumentation, and high-resolution measurement systems.

The LT1007 combines a 2.5 nV/√Hz noise density with a 2 Hz 1/f corner frequency and approximately 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. Its 10 µV offset voltage and 0.2 µV/°C drift support accurate DC measurements, while 130 dB common-mode rejection and 130 dB power-supply rejection reduce errors caused by common-mode voltages and imperfect supply rails. These characteristics are particularly valuable when the input signal is smaller than the unwanted offsets, noise, or supply ripple present in the measurement chain.

The series uses precision internal design techniques to achieve low noise and stable operation. The standard LT1007 is stable for closed-loop gains of 5 or higher, while the decompensated LT1037 provides higher gain-bandwidth-product performance and is also stable at gain 5 or above. Designers must account for this minimum stable gain when selecting feedback values. Decoupling close to the supply pins, maintaining clean ground returns, and avoiding long input traces are therefore central to preserving the intended noise performance.

Typical uses include low-level bridge and thermocouple amplification, precision current-to-voltage conversion, audio and instrumentation preamplifiers, low-level sensor interfaces, and laboratory measurement equipment. In these applications, the LT1007 can amplify weak signals close to its noise floor while rejecting common-mode interference and supply-related disturbance. The 8-pin CERDIP package also supports applications that benefit from a through-hole mechanical format rather than a surface-mount land pattern.

A key design consideration is that minimum gain stability differs from conventional unity-gain-stable amplifiers. Feedback configurations must provide a gain of at least 5, and input/output capacitance should be checked against the frequency-response and stability requirements in the manufacturer datasheet. Low-noise performance also depends on resistor selection, source impedance, grounding, supply bypassing, and shielding rather than the amplifier alone.

This product overview consolidates the LT1007CJ8 electrical characteristics, package information, drop-in-family alternatives, and practical application guidance. It supports faster engineering comparisons while directing detailed pin assignments, test conditions, and absolute-maximum ratings to the official Analog Devices LT1007 datasheet and product documentation.

直接替换替代料: LT1007CJ8 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LT1007CJ8 (相同外形与封装尺寸) ——差异在于 Package, Amplifier Type.

Analog Devices
Package: 8-pin CERDIP (CDIP)
对比 LT1007CJ8 →
Analog Devices
Package: 8-pin CERDIP, 0.300 inch (7.62 mm)
Amplifier Type: Precision operational amplifier
对比 LT1007CJ8 →

LT1037CJ8

✅ 直接替换 ⚠️ 规格未核验
Analog Devices
📦 8-pin CERDIP
Precision operational amplifier · 1 circuit · 60 MHz · 2.5 nV/√Hz · 4.5 nV/√Hz · 3.8 nV/√Hz · 60 nV peak-to-peak · 2 Hz

联系询价

查看数据手册 →

LT1007ACJ8

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin CERDIP
LT1007ACJ8 is the closely related grade and ordering variant of LT1007 in the same 8-pin CERDIP format; exact offset, temperature, and ordering limits must be compared before substitution.

📋 参考替代料(不在目录中)

LT1012CJ8

✅ 直接替换 ⚠️ 规格未核验
Analog Devices
📦 8-pin CERDIP
1-circuit precision operational amplifier · Internally compensated · ±20 V maximum · Picoampere class · 1,000,000 V/V · 5 mA · 1 mW on two Ni-Cad batteries

联系询价

查看数据手册 →

LT1013CJ8

✅ 直接替换 ⚠️ 规格未核验
Analog Devices
📦 8-pin CERDIP
兼容规格

联系询价

查看数据手册 →

LT1006CJ8

✅ 直接替换 ⚠️ 规格未核验
📦 8-pin CERDIP
LT1006 is a lower-noise precision single amplifier in the same 8-pin CERDIP format, but offset, drift, gain stability, and bandwidth differ from LT1007 and require circuit-level validation.

📋 参考替代料(不在目录中)

LT1007CJ8 最大额定值与电气特性

Amplifier Type Single operational amplifier
Number of Circuits 1 circuit
Wideband Input Noise Density 2.5 nV/√Hz
Guaranteed 10 Hz Noise Density 4.5 nV/√Hz
Guaranteed 1 kHz Noise Density 3.8 nV/√Hz
0.1 Hz to 10 Hz Noise 60 nV peak-to-peak typical
1/f Corner Frequency 2 Hz
Input Offset Voltage 10 µV
Input Offset Drift 0.2 µV/°C
Common-Mode Rejection Ratio 130 dB
Power-Supply Rejection Ratio 130 dB
LT1037 Gain-Bandwidth Product 60 MHz
Minimum Stable Closed-Loop Gain 5
Minimum Voltage Gain 2 million typical
封装 8-pin CERDIP
安装类型 Through-hole

LT1007CJ8 8-pin cerdip 引脚配置指南

LT1007CJ8(8-pin cerdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

LT1007CJ8 的 8-pin cerdip 封装引脚图

暂无详细引脚数据: LT1007CJ8.

请参阅 数据手册 以查看完整引脚配置。

典型应用

LT1007CJ8 适用于 6 应用s: Precision Bridge Amplifier, Thermocouple Signal Conditioning, Audio Instrumentation Preamp, Laboratory Voltage Measurement, Precision Current-to-Voltage Conversion, Low-Level Sensor Interface.

🏭

Precision Bridge Amplifier

The LT1007CJ8 fits low-level bridge measurement because its 2.5 nV/√Hz wideband noise and 10 µV offset voltage establish a low noise floor relative to many strain-gauge and resistive-sensor outputs. The 130 dB common-mode rejection helps suppress the relatively large common-mode voltage often present on bridge excitation while the small differential signal is amplified. Place the amplifier where the gain is at least 5 and route input and reference connections away from switching nodes. Resistor matching, excitation symmetry, grounding, and input filtering remain important because amplifier noise alone does not determine the complete measurement accuracy.

🌡️

Thermocouple Signal Conditioning

The LT1007CJ8 is useful for thermocouple and other millivolt-level signal paths because its 10 µV offset voltage and 0.2 µV/°C drift limit static error as temperature changes. The 2.5 nV/√Hz noise density supports low-level amplification where the thermocouple emf can be smaller than the contribution of a higher-noise amplifier. Use a minimum stable gain of 5 and account for thermoelectric junctions at the connector and PCB boundary. Cold-junction compensation, input protection, guarded grounding, and careful high-impedance layout are necessary to preserve the benefit of the amplifier's low offset and noise.

🎧

Audio Instrumentation Preamp

The LT1007CJ8 can serve in a low-noise audio preamplifier when signal integrity and minimum gain are compatible with the application. Its 2.5 nV/√Hz wideband noise density, 60 nV peak-to-peak 0.1 Hz to 10 Hz noise, and 2 Hz 1/f corner make it useful for high-gain microphone and laboratory audio paths. The LT1007 is stable for gains of 5 or higher, so conventional unity-gain microphone layouts may require a different family member. Keep input leads short, use low-value noise-appropriate feedback resistors, and isolate the amplifier from vibration, mains fields, and switching supply noise.

🔧

Laboratory Voltage Measurement

The LT1007CJ8 is appropriate for laboratory front ends that measure small voltages with demanding accuracy. Its 10 µV offset, 0.2 µV/°C drift, and 130 dB common-mode rejection reduce errors from input offset, temperature change, and common-mode voltage. The 130 dB power-supply rejection also helps when the available supply contains ripple. Configure the closed-loop gain at 5 or above and use a shielded, guarded layout to reduce leakage and thermoelectric effects. The amplifier should be calibrated with the complete front end so resistor tolerances, source impedance, reference quality, and acquisition-system offsets are represented in the final uncertainty.

⚡

Precision Current-to-Voltage Conversion

The LT1007CJ8 is useful for current-to-voltage conversion when the sensed current produces a signal near the amplifier's input-noise and offset limits. A transimpedance configuration can benefit from 2.5 nV/√Hz wideband noise and 10 µV input offset, while the high common-mode rejection reduces disturbance from supply and ground variations. Choose feedback resistance and gain carefully because very high transimpedance values interact with input and parasitic capacitance and can reduce stability. Confirm that the selected gain remains at least 5, and evaluate the complete input network, guarding, compensation, and settling behavior rather than relying on amplifier specifications alone.

🧩

Low-Level Sensor Interface

The LT1007CJ8 supports precision sensor interfaces for resistive, magnetic, optical, and other analog sensors whose output changes are small relative to common-mode voltage or supply variation. Its 130 dB common-mode rejection and 130 dB power-supply rejection help protect weak signals, while the low offset and drift reduce errors over time and temperature. The device's minimum stable gain of 5 must be included early in the signal-chain design. Use short guarded inputs, low-noise feedback components, clean references, and local supply bypassing; these implementation details often determine whether the amplifier achieves its datasheet-level performance in a complete instrument.

推荐产品汇总

LT1007ACJ8 Same-family ceramic-DIP precision amplifier 用于: Precision Bridge Amplifier, Thermocouple Signal Conditioning, Audio Instrumentation Preamp, Low-Level Sensor Interface LT1037CJ8 Analog Devices 用于: Precision Bridge Amplifier, Laboratory Voltage Measurement LT1012CJ8 Analog Devices 用于: Thermocouple Signal Conditioning, Precision Current-to-Voltage Conversion, Low-Level Sensor Interface LT1006CJ8 Lower-noise same-family ceramic-DIP option 用于: Audio Instrumentation Preamp, Precision Current-to-Voltage Conversion LT1013CJ8 Analog Devices 用于: Laboratory Voltage Measurement, Low-Level Sensor Interface
What are the key specifications of LT1007CJ8 that engineers should know?
The LT1007CJ8 is a precision, low-noise operational amplifier with 2.5 nV/√Hz wideband noise, 10 µV offset voltage, 0.2 µV/°C offset drift, 130 dB common-mode rejection, and 130 dB power-supply rejection. It is offered in an 8-pin CERDIP package. According to the Analog Devices LT1007 datasheet and product information, the family also provides guaranteed noise densities of 4.5 nV/√Hz at 10 Hz and 3.8 nV/√Hz at 1 kHz. These figures make the device relevant to instrumentation, sensor conditioning, and other applications in which input-referred noise and DC error must remain small relative to the measured signal.
Where can I download the LT1007CJ8 datasheet PDF?
The official LT1007CJ8 technical information is available from the Analog Devices LT1007 product page at https://www.analog.com/en/products/lt1007.html, where the manufacturer datasheet and supporting documentation can be selected. The LT1007CJ8 is the 8-pin CERDIP orderable variant of the LT1007/LT1037 family. Use the manufacturer pin-description table and electrical-characteristics tables when assigning the through-hole footprint, checking supply limits, selecting feedback components, and confirming operating-temperature limits.
Where can I find the LT1007CJ8 pinout?
Use the pin-description diagram in the Analog Devices LT1007 datasheet to determine the LT1007CJ8 pin assignments. The distributor listing identifies the orderable part as a single operational amplifier in an 8-pin CERDIP package, but the individual pin numbers and functions are not repeated on that page. Do not infer the pinout from an 8-pin drawing alone; confirm offset, null, output, supply, and compensation-pin assignments against the manufacturer document before laying out the PCB or wiring the device.
Is LT1007CJ8 suitable for low-level sensor signal conditioning?
The LT1007CJ8 is suitable for low-level sensor signal conditioning because its 2.5 nV/√Hz wideband noise, 10 µV offset voltage, and 130 dB common-mode rejection help preserve small signals during amplification. According to the Analog Devices LT1007 documentation, its 2 Hz 1/f corner also improves low-frequency noise behavior. The device is especially appropriate for precision bridges, strain gauges, thermocouples, and laboratory sensors where signal amplitude is comparable to the amplifier's own noise and offset.
What is the minimum stable gain of the LT1007CJ8?
The LT1007 is intended for closed-loop gains of 5 or greater. According to the Analog Devices product information, the decompensated LT1037 variant also has a 60 MHz gain-bandwidth product while remaining stable for gains of at least 5. This minimum-gain requirement distinguishes the device from a unity-gain-stable precision amplifier. Feedback ratios must therefore be selected carefully, and the stability and frequency-response details in the manufacturer datasheet should be checked before compensation or bandwidth optimization.
How much noise does the LT1007CJ8 have?
The LT1007CJ8 has 2.5 nV/√Hz wideband input-noise density, with guaranteed values of 4.5 nV/√Hz at 10 Hz and 3.8 nV/√Hz at 1 kHz. According to the Analog Devices LT1007 documentation, the family also has a 2 Hz 1/f corner and approximately 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. These characteristics support precision amplification, but total circuit noise also depends on source impedance, feedback resistors, bandwidth, grounding, and shielding.
What is the difference between LT1007CJ8 and LT1007CN8?
The principal documented distinction is the package construction: the LT1007CJ8 is listed as an 8-pin CERDIP part, while the LT1007CN8 uses an 8-pin plastic DIP package. Both orderable variants belong to the LT1007 precision low-noise amplifier family, but their connector and assembly details differ. Verify the exact pin functions, electrical limits, and ordering information in the manufacturer datasheet before treating either variant as a substitute for a specific PCB or socket.
LT1007CJ8 vs LT1037CJ8 — which is better for a fast precision amplifier?
The LT1037CJ8 is generally the better choice when higher closed-loop speed is the priority because the manufacturer highlights a 60 MHz gain-bandwidth product for the decompensated LT1037. The LT1007CJ8 remains appropriate when low noise and precision are the dominant requirements. Both require a minimum stable closed-loop gain of 5 according to the Analog Devices LT1007/LT1037 information. Select the device based on the required noise, gain-bandwidth interaction, stability, and available compensation rather than package alone.
When should I choose LT1007CJ8 over LT1007ACJ8?
Choose the LT1007CJ8 when the exact LT1007CJ8 ordering code, ceramic-DIP mechanical format, and specified LT1007 performance are required. The LT1007ACJ8 is a closely related member of the same 8-pin ceramic-DIP family, but its exact electrical limits and ordering differences must be checked in the manufacturer datasheet before substitution. For new designs, confirm gain stability, supply range, offset limits, noise guarantees, and operating-temperature grade rather than relying on the family name alone.
What can replace LT1007CJ8 without changing the PCB footprint?
A valid replacement must use the same 8-pin CERDIP footprint, preserve the LT1007 pin arrangement, and satisfy the circuit's gain, noise, offset, supply, and stability requirements. Candidates such as LT1037CJ8, LT1007ACJ8, LT1012CJ8, LT1013CJ8, and LT1006CJ8 belong to the same Analog Devices family and use the comparable ceramic-DIP format, but each has different speed, noise, offset, and gain-stability characteristics. Verify the exact alternative and its datasheet before marking the PCB as reusable.
Is there a cross-brand drop-in equivalent for LT1007CJ8?
No cross-brand drop-in equivalent is established by the available manufacturer and cross-reference information, so engineers should not substitute a competitor solely from a similar noise rating. The documented alternatives are from Analog Devices and use the related ceramic-DIP family format, while functional equivalence is not the same as guaranteed pin-to-pin replacement. Confirm the complete pin map, minimum stable gain, common-mode range, supply voltage, noise spectrum, offset drift, and temperature limits in the selected manufacturer datasheet.
Where can I buy LT1007CJ8 online?
Use the Request a Quote form on this page to request LT1007CJ8 availability, current unit pricing, minimum order quantity, and lead time. The exact current commercial terms should be confirmed at the time of quotation because availability and production schedules can change. Before requesting a shipment, specify the exact MPN LT1007CJ8, the required quantity, and whether the ceramic-DIP packaging and any date-code or traceability requirements must be retained.
What is the price of LT1007CJ8?
The current price for LT1007CJ8 should be requested through the Request a Quote form on this page. The form can provide the applicable unit terms for the requested quantity, along with current availability and lead time. For procurement, include the exact MPN, target quantity, delivery location, and any required traceability details. Do not treat a legacy or secondary-market reference as a firm quotation for the exact LT1007CJ8 orderable part.
Is LT1007CJ8 in stock and what is the lead time?
Current LT1007CJ8 stock, minimum order quantity, and lead time should be confirmed through the Request a Quote form on this page. Distributor availability can change independently of the manufacturer's lifecycle status, and a listing's presence does not establish a guaranteed allocation. When requesting a quotation, state the required quantity, production schedule, shipment destination, and whether partial delivery or obsolete-material traceability is acceptable.
Does LT1007CJ8 meet RoHS and REACH requirements?
The RoHS and REACH status of the exact LT1007CJ8 orderable part must be confirmed from the current Analog Devices product documentation or a supplier declaration. A family-level description of the LT1007/LT1037 series does not automatically establish the compliance status of every historical ceramic-DIP ordering code. Request the material-compliance statement for LT1007CJ8 before using it in a controlled production program, especially where the original component has an extended service history.

工程参考数据: LT1007CJ8 ——对比、设计指导和合规信息。

选型指南

Choose the LT1007CJ8 when the design needs a single, low-noise precision amplifier with 2.5 nV/√Hz wideband noise, 10 µV offset, low drift, and 130 dB common-mode and power-supply rejection. Its 8-pin CERDIP format is useful where a through-hole package is preferred and the circuit can operate with a closed-loop gain of at least 5. Choose the LT1037CJ8 when the same family footprint is needed but the 60 MHz gain-bandwidth product is more important than the standard LT1007 configuration. Consider the LT1007ACJ8 only after confirming the exact ordering-grade differences. LT1012CJ8 favors lower-power operation, LT1013CJ8 provides two amplifiers in one package, and LT1006CJ8 is a lower-noise family option with different offset and stability trade-offs. For every alternative, verify pin assignments, supply range, common-mode limits, temperature grade, noise, drift, and gain stability before approving a substitution.

与替代料对比

参数 本产品 LT1037CJ8 LT1007ACJ8 LT1012CJ8 LT1013CJ8 LT1006CJ8
Package 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Circuit Configuration Single amplifier Single amplifier Single amplifier Single amplifier Dual amplifier Single amplifier

关键差异点

  • Very low wideband input noise (对比 LT1013CJ8)
  • Strong DC rejection and stability (对比 LT1012CJ8)
  • Higher-speed option in the same ceramic-DIP family (对比 LT1007CJ8)

设计说明

Do not treat the LT1007 as a unity-gain-stable amplifier. The manufacturer specifies stability for closed-loop gains of 5 or greater, so verify the feedback ratio before committing the PCB. The LT1037 variant is also decompensated and remains stable at gain 5 or above. For inverting or differential circuits, calculate the noise gain rather than relying only on the signal gain, and confirm bandwidth and stability using the applicable manufacturer curves.

Preserve low-noise performance by placing input and compensation networks close to the appropriate device pins and by keeping sensitive input traces short. Avoid routing inputs alongside switching-regulator traces, relay contacts, high-current motor lines, or clock and data edges. Use a continuous ground reference beneath sensitive analog sections, provide local supply bypassing, and avoid creating ground-current paths through input return conductors.

The low 2.5 nV/√Hz noise density is valuable only if the rest of the signal chain does not add more noise. Select feedback resistors with suitable thermal noise and temperature coefficients, minimize source impedance where practical, and apply gain of at least 5. For very high source impedances, account for bias-current errors and resistor-generated noise. For long or high-impedance nodes, use guarding and consider the 60 nV peak-to-peak 0.1 Hz to 10 Hz family noise when evaluating drift performance.

Estimated: the LT1007CJ8 dissipation can be calculated as P = (VIN - VOUT) × IOUT plus the supply current contribution. If VIN is 15 V, VOUT is 5 V, and IOUT is 10 mA, the estimated pass-element dissipation is 0.10 W before bias current. Check this against the device's package thermal limits, ambient temperature, and socket or PCB thermal resistance. The amplifier's low-noise performance does not remove the need for temperature-rise and stability analysis.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The exact compliance declarations for LT1007CJ8 require confirmation from the current Analog Devices product documentation or a supplier compliance statement. AEC-Q100 qualification is not applicable to this general-purpose instrumentation amplifier.

相关搜索

LT1007CJ8 datasheet LT1007CJ8 datasheet pdf LT1007CJ8 pinout LT1007CJ8 equivalent LT1007CJ8 replacement LT1007CJ8 cross reference LT1007CJ8 price LT1007CJ8 stock Analog Devices LT1007CJ8 LT1007 2.5 nV/Hz amplifier LT1007 8 pin CERDIP LT1007CJ8 vs LT1037CJ8

相关元器件 & 术语

Analog Devices LT1007CJ8 LT1037CJ8 LT1007ACJ8 LT1012CJ8 LT1013CJ8 LT1006CJ8 operational amplifier precision amplifier low-noise amplifier instrumentation amplifier signal conditioner voltage noise density input offset voltage input offset drift common-mode rejection ratio power-supply rejection ratio gain-bandwidth product minimum stable gain 8-pin CERDIP through-hole package bridge sensor thermocouple transimpedance amplifier RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情