LT1102CJ8 - 10/100 Gain Precision Amplifier | Analog Devices
Référence : LT1102CJ8 ✗ Fin de vieLT1102CJ8 Présentation
An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals superimposed on larger common-mode voltages. Its internal topology amplifies the difference between two inputs while rejecting shared voltage and noise. The LT1102 belongs to the instrumentation-amplifier hierarchy within the broader amplifier and analog signal-processing categories, and its JFET input stage is suited to high-impedance sources.
The device provides gain accuracy of 0.01% and non-linearity of 3 ppm, eliminating the need for an external gain-setting resistor. According to the Analog Devices LT1102 product information, input bias and offset currents are below 10 pA, while offset voltage is approximately 180 µV. A gain-bandwidth product of 3.5 MHz and slew rate of 30 V/µs support accurate response to rapidly changing input signals.
The fixed-gain architecture simplifies instrumentation front ends by moving gain selection inside the package. It is particularly useful when a system needs repeatable gain accuracy with minimal external components. Users should still account for input and output bandwidth, common-mode range, output swing, and noise when designing a complete analog signal chain.
Typical uses include high-impedance sensor interfaces, bridge-amplifier signal conditioning, biomedical instrumentation, laboratory measurement systems, and industrial acquisition electronics. The JFET inputs are particularly relevant when source leakage or bias-current error would otherwise compromise a precision measurement.
Layout should keep sensitive input traces short, provide a stable reference return, and place input compensation or filtering components close to the device. Where the source impedance is high, parasitic capacitance and leakage can create settling errors even when the amplifier itself has a fast slew rate.
This page combines the manufacturer specifications, package information, comparison points, and engineering-oriented selection guidance. It also distinguishes confirmed alternatives from unverified cross-reference listings so engineers can assess replacement risk before modifying a PCB.
Alternatives de remplacement direct pour LT1102CJ8 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
LT1102ACN8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1102CN8
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1102CJ8 Valeurs maximales et caractéristiques électriques
| Product Type | Instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Input Stage | JFET input |
| Available Fixed Gains | 10 or 100 |
| Gain Accuracy | 0.01% |
| Non-Linearity | 3 ppm |
| Maximum Input Bias Current | Less than 10 pA |
| Maximum Input Offset Current | Less than 10 pA |
| Offset Voltage | 180 µV |
| Gain-Bandwidth Product | 3.5 MHz |
| Slew Rate | 30 V/µs |
| Boîtier | 8-CDIP (0.300 in, 7.62 mm) |
| Terminal Count | 8 terminals |
| Type de montage | Through-hole |
| Temperature Grade | Commercial |
Guide de configuration des broches du LT1102CJ8 8-cdip (0.300 in, 7.62 mm)
Configuration des broches du LT1102CJ8 (boîtier 8-cdip (0.300 in, 7.62 mm)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LT1102CJ8.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LT1102CJ8 convient pour 6 applications: High-Impedance Sensor Signal Conditioning, Strain Gauge and Bridge Measurement, Biomedical and Electrochemical Measurement, Laboratory Data Acquisition, Industrial Process Monitoring, Precision Waveform and Transient Capture.
High-Impedance Sensor Signal Conditioning
The LT1102CJ8 is suitable for conditioning weak differential sensor outputs while limiting bias-current error. Its JFET input stage provides bias and offset currents below 10 pA, while the internal fixed gain of 10 or 100 avoids an external gain-setting resistor. The 0.01% gain accuracy and 3 ppm non-linearity help preserve the integrity of measurements from high-impedance probes, chemical sensors, and precision resistive bridges. The 3.5 MHz gain-bandwidth product also supports acquisition bandwidth beyond static voltmeter use, although source capacitance and sensor settling time must be included in the overall system response.
Recommandé
Strain Gauge and Bridge Measurement
The LT1102CJ8 can amplify the small differential voltage generated by a resistive strain-gauge bridge while rejecting the larger common-mode excitation voltage. Its sub-10-pA input currents reduce errors when long leads or high-impedance bridge nodes increase sensitivity to leakage. Fixed internal gain provides repeatable 10 or 100 multiplication with 0.01% gain accuracy, avoiding resistor-calibration uncertainty associated with many external gain networks. For practical bridge designs, place the amplifier close to the bridge, maintain symmetric input routing, and confirm that the selected gain remains stable within the device's operating limits and output-swing constraints.
Recommandé
Biomedical and Electrochemical Measurement
The LT1102CJ8 is appropriate for low-level biomedical and electrochemical signals where source leakage can create measurement errors comparable to the signal itself. JFET inputs with bias and offset currents below 10 pA help preserve the integrity of high-impedance electrode measurements, while 180 µV offset voltage establishes the basic input-referred accuracy. The 30 V/µs slew rate and 3.5 MHz gain-bandwidth product support faster waveforms than a purely precision DC amplifier. Designers should still account for electrode polarization, patient protection requirements, guarding, leakage paths, and the instrumentation amplifier's common-mode and output-voltage limits.
Recommandé
Laboratory Data Acquisition
The LT1102CJ8 supports laboratory measurement front ends that need both accurate gain and useful signal bandwidth. Its internal gains of 10 or 100, 0.01% gain accuracy, and 3 ppm non-linearity provide repeatable scaling without an external gain resistor. A 3.5 MHz gain-bandwidth product and 30 V/µs slew rate allow the amplifier to process rapidly changing signals, subject to the selected gain and output limits. The device is particularly useful for buffering moderate-impedance transducers, diagnostic probes, and compact instrumentation systems. Keep input filtering outside the fast-signal path unless noise control is required, and use a low-noise reference supply to preserve the available measurement fidelity.
Recommandé
Industrial Process Monitoring
The LT1102CJ8 can condition low-level process signals when sensor leads, grounding, and common-mode voltage make simple differential input stages inadequate. Its instrumentation-amplifier architecture rejects shared voltage, while JFET input currents below 10 pA limit errors caused by leakage into high-impedance transducers. Fixed gain and 0.01% accuracy simplify calibration, and the 30 V/µs slew rate provides headroom for transient process events. In an industrial implementation, keep sensitive traces away from switching nodes and power converters, provide a clean return path, and confirm that the 8-CDIP package has adequate spacing for voltage isolation and service requirements.
Recommandé
Precision Waveform and Transient Capture
The LT1102CJ8 is useful when a measurement chain needs more bandwidth than ordinary precision DC instrumentation amplifiers provide. Its 3.5 MHz gain-bandwidth product supports wider-band signal capture, while the 30 V/µs slew rate reduces large-signal rise-time distortion. The fixed internal gain of 10 or 100 allows designers to avoid external gain-setting resistors and retain 0.01% gain accuracy with 3 ppm non-linearity. Input bias currents below 10 pA benefit high-impedance sources. Care is required when the selected gain closes the usable bandwidth, and the output must remain inside its voltage swing range during transient peaks.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LT1102CJ8 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LT1102ACN8#PBF | LT1102CN8 |
|---|---|---|---|
| Package | 8-CDIP (0.300 in, 7.62 mm) | 8-pin ceramic DIP | 8-pin ceramic DIP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier |
| Fixed Gain Options | 10 or 100 | 10 or 100; exact ordering-code gain requires confirmation | 10 or 100; exact ordering-code gain requires confirmation |
| Gain Accuracy | 0.01% | 0.01% for the LT1102 family | 0.01% for the LT1102 family |
| Non-Linearity | 3 ppm | 3 ppm for the LT1102 family | 3 ppm for the LT1102 family |
| Gain-Bandwidth Product | 3.5 MHz | 3.5 MHz for the LT1102 family | 3.5 MHz for the LT1102 family |
| Slew Rate | 30 V/µs | 30 V/µs for the LT1102 family | 30 V/µs for the LT1102 family |
Principaux différenciateurs
- Accurate gain implemented internally (vs LT1102CN8)
- Very low input leakage for precision sources (vs LT1102ACN8#PBF)
- Fast large-signal response (vs LT1102CN8)
- Compact instrumentation function in eight pins (vs LT1102ACN8#PBF)
Notes de conception
Route the two differential inputs as a closely matched pair and keep them short, away from switching nodes and high-current return paths. Instrumentation-amplifier input bias-current error depends on source impedance, so unequal lead lengths, leakage through PCB contamination, and nearby power circuitry can degrade accuracy. Place any input filtering capacitors close to the relevant input pins, and use a continuous ground reference beneath the analog signal path.
Do not assume that every LT1102 ordering suffix is interchangeable without checking the selected fixed gain and pinout. The CJ8, CN8, and ACN8#PBF identifiers refer to related 8-pin family variants, but package construction, gain selection, and ordering temperature grade can differ. Verify the gain configuration and all eight connections in the manufacturer pin-description table before substituting a part on an existing PCB.
Account for the gain-dependent bandwidth and the 30 V/µs slew rate when defining the expected measurement bandwidth. A 3.5 MHz gain-bandwidth product does not imply the same closed-loop bandwidth at every internal gain setting. Also check output swing against transient peaks. Source capacitance, probe capacitance, and long input wiring can introduce settling behavior that is separate from the amplifier's specified gain-bandwidth product.
Use a clean, low-noise supply and confirm the LT1102CJ8's operating and absolute-maximum voltage limits in the manufacturer datasheet. Decoupling capacitors should be placed near the device's supply pins, with short return paths and an appropriate ground plane. Because the available product information does not state the supply range or quiescent current, these values must not be inferred when designing the power tree.
Informations de conformité
The verified product information identifies a commercial-grade instrumentation amplifier but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the identified commercial-grade LT1102CJ8 ordering configuration.