LTC2282CUP - Dual 12-Bit 105Msps Low Power 3V ADC | ADI
Référence : LTC2282CUP ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $32.85 | $32,85 |
| 10 | $28.9 | $289,00 |
| 100 | $24.75 | $2 475,00 |
| 500 | $21.2 | $10 600,00 |
| 1 000 | $18.5 | $18 500,00 |
LTC2282CUP Présentation
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog input voltages and converts each sample into a discrete digital code, forming the bridge between the analog front end and the digital signal-processing chain of a system. ADCs are positioned in the signal-conditioning hierarchy as: sensor/transducer -> analog front end -> ADC -> DSP/FPGA/microprocessor. High-speed, low-power pipelined ADCs like the LTC2282 sit at the heart of imaging, communications, and instrumentation systems where dynamic range and power budget are both critical.
The LTC2282CUP uses a pipelined architecture with per-stage digital error correction, providing 12-bit resolution at sample rates up to 105 Msps. Single 3V supply operation, optional 2.5V to 3.3V logic, and an integrated low-noise reference simplify board design. The differential analog inputs support input ranges of ±0.5V to ±1V, while an internal sample-and-hold handles full-scale input bandwidths of 250 MHz or higher, enabling undersampling of IF bands. Power dissipation is typically 540 mW (per the LTC2282 datasheet 2282fb) when both channels are active at full sample rate.
Typical applications include imaging and ultrasound front ends, baseband or low-IF digital receivers, cable and broadband modems, multi-channel instrumentation, and portable/wireless transceivers. The dual-channel architecture with tightly matched gain and offset also makes the part well suited to I/Q baseband sampling and diversity receivers where channel matching matters.
When designing with this part, pay particular attention to the analog-input common-mode voltage, the ENC sampling-clock duty cycle (50% ±5% recommended), and the layout of the exposed thermal pad to ground. The 64-lead QFN EP must be soldered to a sufficiently large ground pour to achieve the 33 C/W theta_JA figure noted in the manufacturer datasheet. Decouple each supply pin (AVDD, DVDD, OVDD) with a 0.1 uF ceramic plus a 10 uF bulk capacitor placed within 3 mm of the pin.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a faster path to a complete, qualified BOM.
Alternatives de remplacement direct pour LTC2282CUP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LTC2282CUP (même facteur de forme et même empreinte) — différant par Package, SFDR, SNR, Operating Temperature, Sample Rate.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LTC2280CUP
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$15.85 / unité
Voir la fiche technique →LTC2282CUP#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2282IUP
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$33.72 / unité
Voir la fiche technique →LTC2283CUP
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$38.95 / unité
Voir la fiche technique →LTC2284CUP
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
LTC2221CUP
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$34.2 / unité
Voir la fiche technique →LTC2282CUP Valeurs maximales et caractéristiques électriques
| Number of Bits | 12 |
| Number of Inputs | 2 (dual, simultaneous sampling) |
| Sample Rate | 105 Msps |
| Architecture | Pipelined |
| Input Type | Differential, single-ended optional |
| Analog Supply Voltage | 2.85 V to 3.4 V (3 V nominal) |
| Digital Supply Voltage | 2.85 V to 3.4 V (3 V nominal) |
| Input Range (full scale) | 1 V p-p to 2 V p-p differential |
| SNR | 70.1 dB at Nyquist input |
| SFDR | 85 dB at Nyquist input |
| INL (typical) | ±0.4 LSB |
| DNL (typical) | ±0.3 LSB |
| Power Dissipation | 540 mW typical (both channels, 105 Msps) |
| Full-Power Input Bandwidth | 250 MHz |
| Température de fonctionnement | 0C to +70C (C-grade commercial) |
| Boîtier | 64-pin QFN-EP (9x9 mm) |
| Type de montage | Surface Mount |
| Niveau MSL | 1 |
| Statut RoHS | Compliant (LTC2282CUP#PBF variant) |
| Datasheet Document | 2282fb |
Configuration des broches de LTC2282CUP
| Broche 1 | REFT — Internal reference top - decouple to ground |
| Broche 2 | REFB — Internal reference bottom - decouple to ground |
| Broche 3 | CH1+ — Channel 1 differential analog input, positive |
| Broche 4 | CH1- — Channel 1 differential analog input, negative |
| Broche 5 | VCM — Common-mode voltage output |
| Broche 6 | CH2+ — Channel 2 differential analog input, positive |
| Broche 7 | CH2- — Channel 2 differential analog input, negative |
| Broche 8 | SENSE — Reference mode select |
| Broche 9 | REF — Reference voltage input/output |
| Broche 10 | GND — Ground |
| Broche 11 | AVDD — Analog 3V supply |
| Broche 12 | GND — Ground |
| Broche 13 | AVDD — Analog 3V supply |
| Broche 14 | GND — Ground |
| Broche 15 | GND — Ground |
| Broche 16 | D11A — Channel A digital output bit 11 (MSB) |
| Broche 17 | D10A — Channel A digital output bit 10 |
| Broche 18 | D9A — Channel A digital output bit 9 |
| Broche 19 | D8A — Channel A digital output bit 8 |
| Broche 20 | D7A — Channel A digital output bit 7 |
| Broche 21 | D6A — Channel A digital output bit 6 |
| Broche 22 | D5A — Channel A digital output bit 5 |
| Broche 23 | D4A — Channel A digital output bit 4 |
| Broche 24 | D3A — Channel A digital output bit 3 |
| Broche 25 | D2A — Channel A digital output bit 2 |
| Broche 26 | D1A — Channel A digital output bit 1 |
| Broche 27 | D0A — Channel A digital output bit 0 (LSB) |
| Broche 28 | OVDD — Output driver supply |
| Broche 29 | OGND — Output driver ground |
| Broche 30 | D0B — Channel B digital output bit 0 (LSB) |
| Broche 31 | D1B — Channel B digital output bit 1 |
| Broche 32 | D2B — Channel B digital output bit 2 |
| Broche 33 | D3B — Channel B digital output bit 3 |
| Broche 34 | D4B — Channel B digital output bit 4 |
| Broche 35 | D5B — Channel B digital output bit 5 |
| Broche 36 | D6B — Channel B digital output bit 6 |
| Broche 37 | D7B — Channel B digital output bit 7 |
| Broche 38 | D8B — Channel B digital output bit 8 |
| Broche 39 | D9B — Channel B digital output bit 9 |
| Broche 40 | D10B — Channel B digital output bit 10 |
| Broche 41 | D11B — Channel B digital output bit 11 (MSB) |
| Broche 42 | OGND — Output driver ground |
| Broche 43 | OF — Output format / overrange flag |
| Broche 44 | GND — Ground |
| Broche 45 | DVDD — Digital 3V supply |
| Broche 46 | GND — Ground |
| Broche 47 | OGND — Output driver ground |
| Broche 48 | OVDD — Output driver supply |
| Broche 49 | DITH — Dither enable |
| Broche 50 | GND — Ground |
| Broche 51 | CLKOUTA — Clock output for channel A data |
| Broche 52 | CLKOUTB — Clock output for channel B data |
| Broche 53 | OF — Output format / overrange flag |
| Broche 54 | ENC+ — Differential encode clock, positive |
| Broche 55 | ENC- — Differential encode clock, negative |
| Broche 56 | GND — Ground |
| Broche 57 | AVDD — Analog 3V supply |
| Broche 58 | GND — Ground |
| Broche 59 | GND — Ground |
| Broche 60 | AVDD — Analog 3V supply |
| Broche 61 | GND — Ground |
| Broche 62 | VBIAS — Bias voltage - decouple to ground |
| Broche 63 | MODE — Clock mode select |
| Broche 64 | GND — Ground |
Applications typiques
LTC2282CUP convient pour 6 applications: Medical Ultrasound Imaging Front End, Baseband / Low-IF Digital Receiver, Broadband Cable Modem / CMTS Downstream, Multi-Channel Data Acquisition System, Portable / Wireless Transceiver IF Digitizer, Radar / Lidar Signal Processing.
Medical Ultrasound Imaging Front End
The LTC2282CUP's 70.1 dB SNR and 85 dB SFDR at 105 Msps make it a strong fit for medical ultrasound beamforming front ends where dynamic range directly determines diagnostic image quality. Two simultaneously sampling differential channels let the designer capture RF echo signals from adjacent transducer elements with matched gain and offset, preserving beam-steering accuracy across the array. The 250 MHz full-power input bandwidth supports undersampling of 30-50 MHz IF echo signals, and the 540 mW power budget (per datasheet 2282fb) is manageable in cart-based ultrasound systems with multi-channel architectures. Place each LTC2282CUP as a 2:1 MUX feeding subsequent digital down-conversion stages, with a 0.1 uF + 10 uF decoupling network on every supply pin.
Recommandé
Baseband / Low-IF Digital Receiver
The dual 12-bit 105 Msps architecture of the LTC2282CUP directly samples I and Q baseband signals in software-defined radio receivers, eliminating the analog down-conversion chain and improving channel matching for higher image rejection. With 70.1 dB SNR the part delivers 11+ ENOB at IF, sufficient for 3G/4G base-station observation receivers and femtocell digitizers. Single 3V supply operation reduces PMIC complexity in compact radio modules, while the 64-QFN-EP footprint allows the channel density required for multi-antenna MIMO receiver boards. Provide a clean 105 MHz ENC clock with 50% duty cycle to the differential clock inputs, and decouple the analog and digital supply domains with ferrite beads to keep digital switching noise out of the analog input path.
Recommandé
Broadband Cable Modem / CMTS Downstream
The LTC2282CUP's 250 MHz analog input bandwidth and 70.1 dB SNR make it well suited to digitizing downstream QAM carriers in DOCSIS cable modem termination systems and head-end equipment. A single LTC2282CUP captures up to two adjacent 6 MHz or 8 MHz QAM channels simultaneously, supporting channel-bonding architectures. The 12-bit resolution is sufficient for 256-QAM with margin, while the low power dissipation (540 mW) simplifies the thermal design in densely populated head-end shelves. Add a fixed-gain differential amplifier (such as the AD8138) at the input to set the 2 V p-p full scale and provide 50 ohm input termination, then route the LVDS outputs through a controlled-impedance stripline to the downstream FPGA demodulator.
Recommandé
Multi-Channel Data Acquisition System
With two simultaneously sampling 12-bit channels at 105 Msps in one IC, the LTC2282CUP doubles the channel density of multi-channel data acquisition systems used in industrial vibration analysis, sonar arrays, and benchtop instrumentation. Tight gain and offset matching between the two channels (specified in the 2282fb datasheet) is critical for beamforming applications. The 64-QFN-EP package exposes a thermal pad that must be soldered to a 1+ square inch copper pour to achieve the 33 C/W theta_JA figure, keeping junction temperature below 125 C in densely populated PXI-style instruments. Plan for 105 Msps of LVDS or CMOS data offload per channel - 840 Mbps total - and verify FPGA pin-count sufficiency before board layout.
Recommandé
Portable / Wireless Transceiver IF Digitizer
The LTC2282CUP's 3V single-supply operation and 540 mW power dissipation enable portable wireless transceiver IF digitizers where battery life matters. Dual channels can simultaneously sample the I and Q IF signals from a direct-conversion or low-IF mixer, simplifying the radio baseband chain. The 105 Msps sample rate supports IF bandwidths up to 50 MHz with margin, adequate for Wi-Fi 802.11n, WiMAX, and proprietary wideband protocols. The C-grade 0 C to +70 C commercial temperature range is acceptable for indoor portable devices; use the LTC2282IUP industrial variant for outdoor or vehicular deployment. Drive the clock input from a low-jitter PLL such as the LTC6946-1, and add a series ferrite on each supply pin to suppress digital switching noise from leaking into the radio front end.
Recommandé
Radar / Lidar Signal Processing
The 250 MHz full-power input bandwidth and 12-bit 105 Msps dual-channel capability of the LTC2282CUP support IF sampling in short-range radar and lidar signal-processing chains, where 70.1 dB SNR preserves range resolution on weak returns. Differential inputs reject common-mode noise from switching power supplies on the platform, while the small 64-QFN-EP footprint (9x9 mm) keeps the analog front end compact enough to fit alongside an FPGA in tight enclosures. For automotive AEC-Q100 requirements, evaluate the LTC2282IUP industrial variant (-40 C to +85 C) as an alternative. Lay the analog inputs and the ENC clock traces as matched-length differential pairs on the top layer, with a continuous ground plane beneath, and use the exposed pad as the only ground connection for the analog front end.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LTC2282CUP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LTC2280CUP | LTC2282CUP#PBF | LTC2282IUP | LTC2283CUP | LTC2284CUP |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN-EP (9x9 mm) | 64-QFN-EP (9x9 mm) - same | 64-QFN-EP (9x9 mm) - same | 64-QFN-EP (9x9 mm) - same | 64-QFN-EP (9x9 mm) - same | 64-QFN-EP (9x9 mm) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 14 bit (+2 bits) |
| Sample Rate | 105 Msps | 10 Msps (-90%) | 105 Msps | 105 Msps | 80 Msps (-24%) | 105 Msps |
| Number of Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| SNR (Nyquist) | 70.1 dB | 70.1 dB | 70.1 dB | 70.1 dB | 70.1 dB | 73.4 dB |
| Supply Voltage | 3 V (2.85-3.4 V) | 3 V (2.85-3.4 V) | 3 V (2.85-3.4 V) | 3 V (2.85-3.4 V) | 3 V (2.85-3.4 V) | 3 V (2.85-3.4 V) |
| Operating Temperature | 0C to +70C (C-grade) | 0C to +70C | 0C to +70C | -40C to +85C | 0C to +70C | 0C to +70C |
| RoHS Status | Compliant (LTC2282CUP#PBF variant) | Compliant (#PBF variant) | Compliant | Compliant | Compliant | Compliant |
Principaux différenciateurs
- Dual simultaneously-sampling 12-bit channels at 105 Msps in a single 64-QFN-EP IC (vs LTC2280CUP)
- Pin-compatible 14-bit upgrade path in the same package (vs LTC2284CUP)
- Higher commercial sample rate than the LTC2283CUP family member (vs LTC2283CUP)
- Industrial temperature variant available in the same package (vs LTC2282IUP)
Notes de conception
The exposed thermal pad (EPAD) on the bottom of the 64-QFN package must be soldered directly to a continuous ground pour of at least 1 square inch to achieve the 33 C/W theta_JA figure noted in the manufacturer datasheet 2282fb. Use multiple thermal vias (0.3 mm drill, 0.5 mm pad) on a 1.0-1.2 mm pitch array under the EPAD to conduct heat to inner ground planes. Keep high-speed digital output traces (D0-D11, CLKOUT) on the opposite side of the board from the analog inputs, and route the ENC+/- clock as a length-matched differential pair on the top layer over a continuous ground plane.
Decouple each AVDD and DVDD pin with a 0.1 uF X7R ceramic placed within 3 mm of the pin, plus a 10 uF bulk tantalum or ceramic on each supply domain. Add a ferrite bead (600 ohm at 100 MHz) between the AVDD and DVDD supply domains to break ground-loop noise from the digital switching returning into the analog path. The OVDD output supply can be tied to AVDD in 3V systems, but a separate filtered supply is recommended when driving long output traces to keep digital switching noise out of the analog return path. Estimated input ripple should be kept below 5 mV p-p per the manufacturer's PSRR spec.
Drive the ENC+/- sampling clock with a low-jitter clock source such as the LTC6946-1 PLL or a clean CMOS oscillator through a balun. Total RMS jitter should be below 1 ps (10 Hz to 1 MHz integration bandwidth) to preserve SNR at 105 Msps. The internal sample-and-hold requires a 50% ±5% duty cycle on ENC - an asymmetric clock reduces SNR by 1-2 dB and degrades SFDR. Keep analog input traces short and matched (CH1+ to CH1- length match < 0.5 mm) and provide a stable common-mode voltage at the VCM pin through the recommended RC network to the analog inputs.
Do not leave the SENSE pin floating - tie it to REF for internal reference mode (1.5V) or to AVDD for external reference mode per the application note in the 2282fb datasheet. Avoid driving analog inputs outside the 0V-to-3V common-mode range or the ESD diodes will clamp and inject non-linear distortion. The CLKOUTA and CLKOUTB outputs are designed to drive the destination FPGA capture register directly; adding a series ferrite or resistor attenuates high-speed edge rates and causes data-correlated jitter. If only one channel is used, power down the second channel by tying the corresponding input to VCM to save 100 mW per the LTC2282 family datasheet.
Informations de conformité
LTC2282CUP#PBF variant is RoHS compliant per Analog Devices product page. Standard LTC2282CUP carries the commercial leaded finish. AEC-Q100 not applicable for commercial-grade dual ADC; consider automotive-grade pin-compatible alternatives if required.
